Electric Fireplace Heater User Manual Model#: Royal Slim36 (BI36), Royal Slim42 (BI42), Royal Slim50(BI50), Royal Slim60 (BI60), Royal Slim74 (BI74), Royal Slim84 (BI84), Royal Slim100(BI100) NO VENTING REQUIRED AC120V 60 Hz 1500 Watts WARNING CAUTION Do Not Return This Item If you have any questions about assembly or operation or missing parts, or product is damagedof this product, please contact us feel free. E-mail: service@velayhome.
Table of Contents Important Instructions ................................................................................................................................ 1 Unpacking And Testing Appliance .............................................................................................. 2 Grounding Appliance .................................................................................................................... 2 Packing List ...........................................................
IMPORTANT: It is important to read these instructions carefully before using the appliance for the first time. Keep the instructions safe so that you can refer to them later if necessary. Important Instructions When using electrical appliances basic precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: Read all instructions before using this heater. 1. This heater is hot when in use. To avoid burning, do not touch hot surface.
⚫ Unpacking And Testing Appliance Remove all parts and hardware from the carton and place them on a clean, soft, dry surface. Check the parts list to make sure no parts are missing. If parts are missing, please contact technical support for replacement. Prior to installing the appliance, test to make sure the appliance operates properly by plugging the power supply cord into a conveniently located 110-120 Volt grounded outlet. NOTE: Dispose of plastic bag, as it may cause choking hazard with young children.
Installation WARNING: Find a safe location and build a suitable hole for fireplace. Minimum clearance from the ceiling and the mantel must be at least 8 inches (200mm); minimum clearance from the front must be at least 3 feet (900mm). Choose a location near an outlet so an extension cord is not required. ⚫ Dimension Front Side Top MODEL SIZE BI42 BI50 BI60 BI74 BI84 A(Inch) 44.02” 52.26” 62.26” 76.13” 86.43” B(Inch) 17.72” 17.72” 17.72” 17.72” 17.72” C(Inch) 42.05” 49.96” 59.96” 74.
Take model BI50 as an example. Prepare a wall with a framed opening of 50.3 inches (1277.5mm) wide 16.2’’(412mm) high. Make sure the width of the woodblock on both sides used to fix the fireplace is 3’’(76mm). Make sure that the revealed woodblock width on both sides is about 1 1/2’’(37.5mm) after finishing the plasterboard. Measure the depth ‘D’ from the plasterboard surface to the woodblock and write it down.
Before installing the in-wall fireplace, please read the following steps carefully. ⚫ Wall-Mounted Fireplace Style 1．Remove the four silver-colored screws (ST4*8-screw) on the top, and take off the wall bracket. 2．Use the screwdriver to drill the wall. 3. Use a hammer to put the screws into the wall together with the wall bracket. ST4*8 Screws Wall bracket Step 1 Step 2 Step 3 4. Lift the fireplace and put it onto the bracket, then lock the 4 silver screws on the top.
⚫ Recessed Fireplace Style 1. Remove the wall bracket first.Take off the 4 silver screws (ST4*8-screw) on the top and then take off the wall bracket from the fireplace. 2. Take off the 2 silver screws (ST4*8-screw) on the left side and right side, then pull out the front glass panel from the fireplace. Step 1 Step 2 3. Put the fireplace into the hole, then fix the 2 silver screws( ST4*40-screw) as the photo from the inside of the fireplace. 4.
Operation Plug the power cord into a 110-120 Volt 15 Amp outlet. Make sure the outlet is in good condition and that the plug is not loose. NEVER exceed the maximum amperage for the circuit. DO NOT plug other appliances into the same circuit. ⚫ Temperature Limiting Control This heater is equipped with a Temperature Limiting Control. Should the heater reach an unsafe temperature(212°F / 100°C), the heater will automatically turn OFF. To reset: 1. Unplug the power cord from the outlet 2.
The touch display panel is shown by LED's on the front bottom right of the appliance. The LED's will appear on the bottom of the fireplace control panel. WARNING: Do not move or remove the mesh trim panel, when the appliance is plugged in and operating. This will cause the remote control and touch panel to no longer function.
⚫ Remote Control Battery Information This remote control uses two AAA batteries (Not included). Instructions for battery installation are on the Remote Control battery compartment. NEVER dispose of batteries in fire. Failure to observe this precaution may result in an explosion. Dispose of batteries at your local hazardous material processing center.
Safety Instructions ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ Only use the appliance in accordance with the instructions in this manual! It cannot be used for any other purpose. Never operate the appliance when the appliance itself or the main cable show any signs of damage. In order to avoid overheating, do not cover the heater. Be responsible when handling the packing material. Warning: plastic wrapping may be lethal to children. Do not place the appliance next to a socket.
Care and Maintenance ⚫ Cleaning instruction ALWAYS turn the heater OFF and unplug the power cord from the outlet before cleaning, performing maintenance, or moving this fireplace. Failure to do so could result in electric shock, fire, or personal injury. NEVER immerse in water or spray with water. Doing so could result in electric shock, fire, or personal injury. Glass: 1 Use a good quality glass cleaner sprayed onto the cloth or towel. Dry thoroughly with a paper towel or lint-free cloth.
Trouble shooting 1. Q: Unit does not heat? A: 1. Turn on the heater to see if the heater will work continuously. 2. If not, unplug the unit for a whole night. And then turn it on again. 3. If still not, contact service team for help 2. Q: Why is there no flame effect? A:1. Make sure the unit is plugged into a power outlet. 2. Check if the main power on the right side of the fire place is turned on. 3. Switch the flame color by the remote or touch screen to check whether there is flame effect. 4.
Limited Warranty ⚫ This warrants to the original purchaser that this product is free from defects in material and workmanship as of the date of purchase and that it will, under normal use and proper care, remain so for one year from the date of purchase. ⚫ Missing or initially defective parts will be replaced free of charge during the period of this limited warranty. If parts are unavailable, comparable replacement of refund will be given.
