WARNING: THIS APPLIANCE IS FOR OUTDOOR USE ONLY! This manual should remain with the parties responsible for operation. Table of Contents Section 1: General Description 1.1 Receiving Checklist 1.2 Product Dimensions 1.3 Product Contents 1.4 Safely Moving Unit Section 2: Safety Instructions Section 3: Installation Details 3.1 Gas Requirements 3.2 Internal View of Components Section 4: Operation 4.1 Ignition 4.
Section 1 General Description 1.1 Receiving Checklist Upon receiving fire feature from transportation carrier 1) Inspect the crate/pallet for damage 2) Check that PO/BOL paperwork matches paperwork on crate/pallet 3) Open top of crate/pallet and inspect unit for damage *If damaged, please notify carrier immediately and sign “damaged” or do not receive. Please also notify Prism Hardscapes office immediately via email at warranty@prismhardscapes.com 1.
Overall Diameter Overall Height Pan Diameter Burner Weight 80" 18" 56" 24” 6-Spoke Burner 600lbs
1.
1.
Section 2 Safety Instructions WARNING Before installing this product, read and follow all warning notices and instructions provided. Failure to do so may result in serious injury, property damage and/or death. For additional product reference and copies of these instructions, visit our website at prismhardsacapes.com This product must be installed and serviced by a contractor or qualified installer who is licensed and/or certified within the jurisdiction where the product will reside.
Prism Hardscapes strongly recommends the installation of Carbon Monoxide detectors within reach of this appliance and in any adjacent occupied spaces. CALIFORNIA PROPOSITION 65 This product can expose you to Chromium, which is known in the state of California to cause cancer, birth defects or other reproductive harm. (for more information, go to: www.p65warnings.ca.gov) WARNING This appliance may produce carbon monoxide which has no odor.
Section 3 Installation Details 3.1 Gas Requirements The fire table should be placed on a flat and level surface. It will arrive with the burner and burner plate set inside the unit. Burner hardware has been installed at the factory but will need to be checked for proper tightness after transportation. Refer to the corresponding section below for set‐up on your unit. All units must have clearance to combustible surface of 4ft on sides & 6ft from the top.
Make sure the foundation is flat and level prior to placement. Units using propane gas will come with a burner, orifice, flex hose and regulator that will attach to the propane tank. This gas hose will need to go from the tank to the burner. The hose should connect from the key valve within the unit, through a vent underneath and to the propane tank.
Section 4 Operation 4.1 Ignition Refer to the section below according to which ignition system you purchased. An initial burner test should be done prior to filling the pan with media (rocks/glass/etc.) 4.1.1 Manual Light You will need a fireplace lighter, do not use a match or cigarette lighter as they are much shorter and will light the fuel too close to the burner which may result in serious injury. Ignite your fireplace lighter and hold the tip close to the burner.
operation. Push knob inward and turn counter clockwise all the way back to the 12:00 starting position. If the knob does not turn the system off, contact your gas professional to replace gas valve. Only use factory approved parts for replacement. Once burner lights, immediately remove your hand and allow burner to operate for a few minutes before turning the knob all the way back to the 12:00/off position. You are now ready to place the fire media onto the burner pan.
Section 5 Troubleshooting Refer to the section below according to which Gas Type you purchased. BURNER WILL NOT LIGHT Possible Cause Air in Gas Line How to Fix If newly installed, it may take several attempts to purge air from line. Debris in Gas Line Confirm gas line is clear and free of obstruction (insulation, dirt, excess pipe sealer, water etc.). Clearing line of debris may require help from a professional.
Excessive Flame Blockage Separate and spread media (rocks or glass) evenly to allow flames to spread and pass‐through media more evenly. Improper Air/Fuel Mixture Remove any foreign items or other combustible materials from unit & check for proper orifice sizing. BURNER FLAME IS TOO HIGH OR TOO LOW Possible Cause Incorrect Gas Supply Pressure How to Fix Propane Gas Units: Inspect propane tank and hose, one or both may need to be refilled or replaced. Natural Gas Units: Contact local gas company.
Section 6 Warranty Prism Hardscapes LLC offers a 2‐year limited warranty against manufacturer defects. Prism Hardscapes will repair or replace product which has been proven to be defective in workmanship and/or material. If unit is confirmed defective and is not repairable by a qualified Prism Hardscapes representative, the unit will be replaced FOB PRISM HARDSCAPES facility.
