TABLE OF CONTENTS PRECAUTIONS ............................................................................................................................... 2 INSTALLATION...................................................................................................................................... 2 POWER CONNECTION............................................................................................................................ 2 MAINTENANCE.................................................
Precautions Installation 1.Do not cover or block the ventilation ports on the rear of the monitor. 2.Do not install the monitor close to heat sources such as radiators or air ducts, or in a location exposed to direct sunlight, excessive dust, mechanical vibration,or shock. Power connection 1.Use the correct power cord for your local voltage. 2.Use an accessible outlet close to the monitor. 3.Do not allow anything to rest on the power cable. 4.Only use the power adapter attached to the monitor. 5.
Getting Started Package contents Before beginning, ensure that the carton contains the following items: 1.LCD Monitor 2.Power cord (The plug may vary according to the electrical standard for your area) 3.Video Signal Cable (Analog, D-SUB Cable) 4.Audio cable (optional) 5.CD-ROM (Contains the driver of the monitor, this user’s manual and other information) 6.
Installation of First Use 1.The installation of the monitor is very simple. What you need to do is to take the monitor from the packing box and remove all the packing materials. And then put the monitor on the desk carefully; fold the monitor base, so that the monitor can stand on the desk properly. Next, adjust the monitor to a desired position according to the seat and other factors. Identifying parts and controls 1.The LED indicator and control buttons as following 2.
Setup 1.Connecting video (Note: Before connecting computer, ensure the resolution and refresh rate of the computer do not exceed the following settings - resolution: 1280*1024, refresh rate: 75Hz.) 1.1 Turn off your computer 1.2 Connect the video signal cable to the VGA port of your PC, tighten the screws on the connector onto the computer 1.3 Connect the other end of video signal cable to the VGA-IN port at the back of the monitor, tighten the screws on the connector onto the monitor 2.Connecting power 2.
Customizing your Monitor The On Screen Display (OSD) system provides a full range of customizable tools to optimize your display. Important: While full customization is available, we strongly recommend using the Auto Adjustment function, which are preset to fully optimize your monitor’s performance. Simply presses the buttons simultaneously to engage the Auto Adjustment. It is also recommended that you execute the function following any change made to your display from your computer.
OSD Icon List Icon Functions Detail Optimize the picture performance automatically (you may also press _ and _ buttons simultaneously, while the OSD menu is not shown, to activate the function) Auto Adjustment Adjust the luminance level of the screen Brightness Adjust the contrast level (black to white ratio) of the screen Contrast Adjust the sharpness of the screen Sharpness Adjust the monitor internal sampling clock rate Clock Adjust the monitor internal signal phase Phase Shift the position
Adjust the position of OSD menu on the screen. OSD Menu Position Select between Standard and Advanced power saving modes. See addendum for details. Power Saving Mode Fulfill EPA Energy Star power management requirement Standard Activate monitor Life-Extension function Advanced Reset monitor parameters back to factory preset values.
Troubleshooting Symptom Check Items 1.No picture 2.LED indicator (at the right side of the monitor) is not lit 1. Check if the monitor is turned on (press the button again). 2. Check if the power cord is properly connected to the monitor and power outlet. 3 .Check if there is electricity coming from the power outlet (use another device to check for power). 1.No picture 2.LED indicator (at the right side of the monitor) is orange 1 Check if your computer is turned on.
Technical Features and Specifications Item Description LCD Display 17" TFT active matrix panel Display Size 337.92(H) x 270.336(V) mm Pixel Pitch 0.264(H) x 0.264(V) mm Resolution Maximum SXGA 1280 x 1024 @75Hz Recommended SXGA 1280 x 1024 @60Hz Max. Display Color 16.2M colors Brightness 300 cd/m2 (typ.) Contrast Ratio 500¡G1 (typ.) Viewing Angle (CR_5) L/R 160o (typ.) U/D 160o (typ.) Response Time (Tr+Tf) 12 ms (typ.) Signal Input D-sub 15 pin Analog Horizontal: 31.
Interface Frequency 1.The following frequency range is the working period. If the entered mode between below period but not match the frequency of supported timing, display optimization would not be assured. If the entered mode is out of the working period, the display will be blanking (just show “Input Signal Out Of Range”) then go to power saving. 2.
Supported timing list 1.If the selected timing is NOT included in table below, this LCD monitor will use the most suitable available timing. Resolution Pixel Clock H Frequency H Total H BP H Width H Size H Frequency 640X350@50Hz 25.175M 31.469KHz 800 48 96 4.000 50.030Hz 640X350@60Hz 25.175M 31.469KHz 800 48 96 4.000 59.941Hz 640X350@70Hz 25.175M 31.469KHz 800 48 96 4.000 70.087Hz 720X350@50Hz 28.322M 31.469KHz 900 54 108 4.000 50.030Hz 720X350@60Hz 28.322M 31.
Resolution Pixel Clock H Frequency H Total H BP H Width H Size H Frequency 1152X864@60Hz 80.000M 54.054KHz 1480 192 96 4.000 59.270Hz 1152X864@70Hz 94.499M 63.851KHz 1480 200 96 4.000 70.012Hz 1152X864@75Hz 108.000M 67.500KHz 1600 256 128 4.000 75.000Hz 1152X870@75Hz 100.000M 68.681KHz 1456 144 128 4.000 75.061Hz 1152X900@66Hz 92.940M 61.795KHz 1504 194 128 4.000 65.950Hz 1152X900@76.2Hz 105.590M 71.732KHz 1472 208 96 4.000 76.068Hz 1152X900@76.
Addendum Advanced Power Saving Mode 1.Background The traditional monitors have the function of electricity-saving dormancy. But the interval of dormancy is difficult to decide. If the interval is long, the purpose of saving electricity can not be achieved. While the interval is short, your computer and LCD monitor would be dormant often. When the LCD monitor becomes dormant, the back lights will be turned off immediately.
5.l How to engage the Monitor Life-Extension function? You may simply use the OSD control to activate the Monitor Life-Extension function. 1. Press the Menu 2. Press or 3. Press the Menu 4. Press or 5. Press the Menu 6. Press or 7. Press the Menu button to activate the OSD menu button to select the Power Saving Mode icon. button to confirm the selection button to select the “Advanced” option in the Power Saving Mode function. button to confirm the selection button to select the Exit icon.
Regulations FCC compliance 1.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 2.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
TCO’99 Congratulations! You have just purchased a TCO’99 approved and labeled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products.
Environmental requirements Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants are chemically related to another group of environmental toxins, PCBs.
