Product Manual

PRINCE MANUFACTURING CORPORATION/WORLD HEADQUARTERS • P.O. BOX 7000 • NORTH SIOUX CITY, SOUTH DAKOTA 57049-7000
URL: www.princehyd.com • E-MAIL: [e-mail] • PHONE [phone] • FAX [phone]
O.E.M. CUSTOMER SERVICE: [phone] • FAX [phone] DISTRIBUTOR CUSTOMER SERVICE: PHONE [phone] • FAX [phone]
P23
PUMPS AND MOTORS
CATP 01-04-09-02
AEM SERIES ROLLER MOTOR – LOW SPEED – HIGH TORQUE
The Prince AEM Series Motors
incorporate the roller principle of
operation offering higher torque
than the ADM and extended life
in heavy-duty continuous high
torque operation along with
modular, compact construction.
Although dimensionally small,
this mo t o r i s c a pa b l e o f
providing considerable power
over a wide speed range and
is instantly reversible by simply
reversing the direction of the
hydraulic uid ow. The needs
of many applications requiring
high starting, stall and running
torque combined with slow
speed are met by this motor.
Feature
• Fully reversible simply by
reversing the direction of
hydraulic uid ow.
• Alternative port positioning
for versatility of installation.
(see next page).
• Optional shaft congurations.
(specials possible).
• Modular construction for
economical servicing and
repair, also permits
special adaptations.
Filtration
10 micron or ner. (Per ISO
cleanliness code level 17/14.
It is not recommended to operate at
a condition requiring both maximum
torque and speed. Splined shafts
are recommended in application
operating at above 2500 in-lbs.
continuous torque or under conditions
of frequent reversal.
Maximum Axial Thrust Load on Shaft 1000 lbs.
0
Intermittent operation = 10% Operation of every minute
TEMP: NORMAL OPERATING 80
0
F TO 140
0
F, MAX 185
0
F
Maximum inlet pressure 2,500 psi for motors in series
Maximum back pressure 1,000 psi
OIL: Mineral based hydraulic uid 100-200 SUS @ operating temperature.
AEM SERIES
Ordering
Code
MOTOR TYPE:
AEM
MOTOR SIZE:
75
100
150
200
250
300
400
MOUNTING:
2 Hole Flange – 2
4 Hole Flange – 4
SHAFT TYPE:
Standard 1” Key R
1” Splined S
1” Tapered T
1” w/Cross-hole U
PORTS:
P – 1/2 NPTF
(Standard)
O – 7/8 x 14 SAE
O-Ring Port
T – Manifold Port Face
(See Next Page)
END PLATE:
(Blank for Standard)
X – Drain Port
(if required)
AEM MOTORS ONLY
To assure optimum motor life, run motor for approximately one hour at
30% of rated pressure before application of full load.
CROSS REFERENCE
CHARLYNN “S” Series
WHITE “RS” Series
ROSS-TRW “MG/MF” Series
DANFOSS “DS” Series
CONT INT
0
CONT INT
0
CONT INT
0
75 75.1 4.6 1700 2400 119 167 800 1000 16.0
100 100.1 6.1 1600 2300 112 160 650 800 16.4
150 150.2 9.2 1500 2200 105 153 400 500 17.2
200 200.2 12.2 1400 2000 98 139 300 400 18.0
250 250.3 15.3 1300 1800 91 125 250 325 18.7
300 300.3 18.4 1200 1600 84 111 200 250 19.5
400 400.4 24.4 1200 1400 84 97 125 160 21.1
AEM
DISPLACEMENT
CC/REV CU.IN/REV
MAXIMUM
PRESSURE
PSI Kgf/CM
2
WT.*
MAXIMUM
SPEED
RPM