Product Manual

PRINCE MANUFACTURING CORPORATION/WORLD HEADQUARTERS • P.O. BOX 7000 • NORTH SIOUX CITY, SOUTH DAKOTA 57049-7000
URL: www.princehyd.com • E-MAIL: [e-mail] • PHONE [phone] • FAX [phone]
O.E.M. CUSTOMER SERVICE: [phone] • FAX [phone] DISTRIBUTOR CUSTOMER SERVICE: PHONE [phone] • FAX [phone]
P21
PUMPS AND MOTORS
CATP 01-04-09-02
ADM SERIES GEROTOR MOTOR – LOW SPEED – HIGH TORQUE
The Prince ADM Series of
high-torque, low speed motors
incorporates the orbiting
gerotor principle for dependable
operation over a wide range
of ap p lications . Altho u gh
dime n s i o nally s mall, t h is
motor is capable of providing
considerable power over a wide
speed range and is instantly
reversible by simply reversing
the direction of the hydraulic
uid ow. The needs of many
applications requiring high
starting, stall and running torque
combined with slow speed are
met by this motor.
Feature
• Fully reversible simply by
reversing the direction of
hydraulic uid ow.
• Alternative port positioning
for versatility of installation.
(see next page).
• Optional shaft congurations.
(see next page).
• Modular construction for
economical servicing and
repair, also permits
special adaptations.
Filtration
10 micron or ner. (Per ISO clean-
liness code level 17/14.
APPLICATIONS
Use the ADM Series for light to medium duty applications such as grain
augers and elevators, salt and sand spreaders, car wash and sweeper
brushes, conveyors, winches, scissor lifts, and many other. To assure
optimum motor life, run motor for approximately one hour at 30% of rated
pressure before application of full load.
It is not recommended to operate at
a condition requiring both maximum
torque and speed. Splined shafts are
recommended in application operating at
above 2500 in-lbs. continuous torque or
under conditions of frequent reversal.
CROSS REFERENCE
CHARLYNN “H” Series
DANFOSS “DH” Series
Maximum Axial Thrust Load on Shaft 1000 lbs.
0
Intermittent operation = 10% Operation of every minute
TEMP: NORMAL OPERATING 80
0
F TO 140
0
F, MAX 185
0
F
Maximum inlet pressure 2,500 psi for motors in series
Maximum back pressure 1,000 psi
OIL: Mineral based hydraulic uid 100-200 SUS @ operating temperature.
ADM SERIES
Ordering
Code
MOTOR TYPE:
ADM
MOTOR SIZE:
50
75
100
150
200
250
300
400
MOUNTING:
2 Hole Flange – 2
4 Hole Flange – 4
SHAFT TYPE:
Standard 1* Key R
1” Splined S
1” Tapered T
1” w/Cross-hole U
PORTS:
P – 1/2 NPTF
(Standard)
O – 7/8 x 14 SAE
O-Ring Port
T – Manifold Port Face
(See Next Page)
END PLATE:
(Blank for Standard)
X – Drain Port
(if required)
ADM MOTORS ONLY
CONT INT
0
CONT INT
0
CONT INT
0
50 49.1 3.0 1400 2200 98 153 800 1000 12.8
75 76.6 4.7 1400 2100 98 146 750 950 13.1
100 99.6 6.1 1300 2000 91 139 600 750 13.4
150 153.2 9.3 1200 1900 84 132 400 500 14.0
200 199.2 12.2 1200 1800 84 125 300 400 14.5
250 252.8 15.3 1100 1700 77 118 250 325 15.0
300 293.2 17.9 1000 1600 70 111 200 250 15.5
400 398.4 24.4 900 1300 63 90 125 160 16.7
ADM
DISPLACEMENT
CC/REV CU.IN/REV
MAXIMUM
PRESSURE
PSI Kgf/CM
2
WT.*
MAXIMUM
SPEED
RPM