> Primare A30.
> Preface COPYRIGHT AND ACKNOWLEDGMENTS Copyright © 2001 Primare Systems AB. All rights reserved. Primare Systems AB Idavägen 17D Warning: To prevent fire or shock hazard, do not expose this unit to rain or moisture. Dangerous voltages inside. Do not open the cabinet. There are no user serviceable parts inside. Repairs should be carried out by qualified service personnel only.
> Contents Introduction Connecting the A30.1 Integrated Amplifier W E L C O M E T O T H E A 3 0 . 1 I N T E G R AT E D B A C K P A N E L C O N N E C T I O N S ........................... (7 P O W E R C O N N E C T I O N ........................................ (8 O U T P U T S ................................................................... (8 I N P U T S ....................................................................... (8 A M P L I F I E R .............................................
> Preface iv §0 Preface 4 14/5/01, 2:00 pm
> Introduction Welcome to the Primare A30.1 Integrated Amplifier! This chapter introduces you to its key features, and explains how you can take advantage of its superb sound as the key component in your hi-fi system. W E L C O M E T O T H E A 3 0 . 1 I N T E G R AT E D A M P L I F I E R The A30.1 is an integrated preamplifier and power amplifier with extraordinary performance for its price. High-performance power amplifier The A30.
> Introduction T E C H N I C A L S P E C I F I C AT I O N Output power per channel 2 x 100W into 8Ω, 2 x 180W into 4Ω Speaker terminals 4 –16Ω Output impedance <0.06Ω DC offset <3mV Balanced inputs 560mV Line inputs 280mV Tape outputs 280mV Frequency response <10Hz – 100kHz, -3dB THD <0.07% at full power Signal-to-noise, line -100dB (A-weighted) Mains 100/115/230V Power consumption 600W max Peak current ±40A Dimensions (WxDxH) 430 x 375 x 100mm Weight 15.
> Using the A30.1 Integrated Amplifier This chapter explains how to operate the A30.1 Integrated Amplifier, using either the front panel controls or the C30 Remote Control. F R O N T PA N E L C O N T R O L S ]A The source switch selects one of the six sources. All the functions of the A30.1 Integrated Amplifier can be accessed using the ]B The MONITOR button selects the tape monitor.
> Using the A30.1 Integrated Amplifier SWITCHING ON AND OFF CHANGING THE VOLUME To switch on The A30.1 allows you to vary the volume from 0 (silence) to 79 (maximum • Use the switch under the left-hand edge of the front panel. volume). During normal operation you can leave the A30.1 switched on and in To change the volume standby.
Using the A30.1 Integrated Amplifier CHANGING THE PHASE The phase button on the front panel can be used to change the phase from 0° < When the monitor output is selected an indicator is shown above the MONITOR button on the front panel display. (non-inverted) to 180° (inverted), to restore absolute phase on source materials The MONITOR button has no effect when the TA source is selected, and the that have been recorded with the incorrect phase. monitor indicator will flash to indicate the error.
> Using the A30.
> Connecting the A30.1 Integrated Amplifier This chapter explains how to connect the A30.1 to the other components in your system, using the connections on the back panel. B A C K PA N E L C O N N E C T I O N S ]A ]B RIGHT SPEAKER – PRE-OUT RIGHT BALANCED INPUT 1 L R ]C BALANCED INPUT 2 R L CD TUNER ]D AUX TAPE1 TAPE1 OUT TAPE OUT PRE-OUT LEFT + LEFT SPEAKER + – GROUND ]E ]F ]G ]H ]I ]A Right loudspeaker outputs. ]E Left preamplifier output. ]H Tape outputs.
> Connecting the A30.1 Integrated Amplifier POWER CONNECTION Warning: Before connecting power check that the required supply voltage, indicated on the back panel, corresponds to your local AC supply. If a different voltage is stated on the type plate do not connect the amplifier to the mains power, and seek advice from your dealer. Connect the mains power using the enclosed mains cable. Note: Always disconnect the amplifier from the mains power before connecting or disconnecting any of the cables.
> Index A O V audio inputs ............................................ 8 outputs ............................................... 7, 8 volume, changing .................................... 4 audio outputs ..................................... 7, 8 loudspeakers ................................. 7, 8 VOLUME CONTROL ................................ 3 preamplifier ................................... 7, 8 B back panel connections ............................ 7 balance, changing ......................
> Index 10 §4 Index 10 14/5/01, 2:00 pm
