Data Sheet

ENGINEERING DATA SHEET
Primacoustic is a division of Radial Engineering Ltd. • 1588 Kebet Way Port Coquitlam, BC V3C 5M5 • Tel: [phone] Fax: [phone]
www.primacoustic.com • [e-mail] • Primacoustic Engineering Data Sheet • Part #R870 2200 00 • Copyright © 2016 • Subject to change without notice.
Push-On Impaler:
Surface Impaler:
Surface Impalers™ are designed to provide the installer with a simple,
quick, and effective method of mounting Broadway™ glass wool panels
onto walls without causing serious surface defacement. Primacoustic
Surface Impalers allow the installer to simply pull the panel down onto
the Impaler clip quickly and efciently, while allowing for some levelling
adjustability after the panel is installed.
The Surface Impaler features four sharp darts that penetrate the panel and
secure it in place. To ensure panels do not get dislodged after installation,
applying a dab of construction adhesive to the center of the Impaler during
the mounting process adds a level of security and reduces opportunity
for tampering. Impalers are installed using typical sheetrock anchors and
screws.
suRFAce iMPAleR
ORDER NUMBER Push-On: F101-1003-00 Surface: F101-1000-00
MATERIAL 20 gauge galvanized steel
DIMENSIONS 3” (76mm) x 4” (102mm)
ATTACHMENT POINTS 2 (Use appropriate fastener for wall surface)
MAX LOAD LIMIT 12 lbs. (5.4 kg.) Dependant on wall fastener
NUMBER PER BOX 24 per box
SPECIFICATIONS:
3” (77mm)
4” (102mm)
Push-on Impalers™ are designed to provide the installer with a simple,
quick and effective method of mounting Broadway™ glass wool panels
onto walls without causing serious surface defacement. Primacoustic
Push-On Impalers allow the installer to push the Broadway panel straight
onto the Impaler clip, making it easier to align panels in clusters or side by
side with accuracy.
The Push-On Impaler features a series of sharp protruding darts that
penetrate the panel and secure it in place. To ensure panels do not get
dislodged after installation, applying a dab of construction adhesive to the
center of the Impaler during the mounting process adds a level of security
and reduces opportunity for tampering. Impalers are installed using typical
sheetrock anchors and screws.
PusH-On iMPAleR
3” (77mm)
4” (102mm)
Order No. Description HEIGHT WIDTH DEPTH
No. of
Impalers
Needed*
F121-1212-xx Scatter Blocks 12” (305mm) 12” (305mm) 1” (25mm) 1
F102-2424-xx Control Cubes 24” (610mm) 24” (610mm) 2” (51mm) 2
F122-2424-xx Control Cubes 24” (610mm) 24” (610mm) 2” (51mm) 2
F121-1248-xx Control Columns 12” (305mm) 48” (1219mm) 1” (25mm) 2
F122-1248-xx Control Columns 12” (305mm) 48” (1219mm) 2” (51mm) 2
F123-1248-xx Control Columns 12” (305mm) 48” (1219mm) 3” (76mm) 2
F121-2448-xx Broadband Panels 24” (610mm) 48” (1219mm) 1” (25mm) 4
F102-2448-xx Broadband Panels 24” (610mm) 48” (1219mm) 2” (51mm) 4
F122-2448-xx Broadband Panels 24” (610mm) 48” (1219mm) 2” (51mm) 4
F103-2448-xx Broadband Panels 24” (610mm) 48” (1219mm) 3” (76mm) 5
F123-2448-xx Broadband Panels 24” (610mm) 48” (1219mm) 3” (76mm) 5
F103-2448-xx Broadband Panels 24” (610mm) 48” (1219mm) 3” (76mm) 5
F123-2448-xx Broadband Panels 24” (610mm) 48” (1219mm) 3” (76mm) 5
RECOMMENDED MINIMUM NUMBER OF IMPALERS PER PANEL:*
*Primacoustic recommends a certain number of impalers per panel as the minimum required for
safe installation based on panel depth and weight. For additional security, you may wish to increase
these numbers per panel and also combine with construction adhesive.
12” x 12” 24” x 24” 12” x 48” 24” x 48”
4” (102mm)
4” (102mm)
Flush mount impaler
clips should be located
approximately 4 inches
(102mm) or more from
the panel edges.