V10 *INFMANU4437*
SAFETY GUIDELINES WARNING! An authorized Pride Provider or qualified technician must perform the initial setup of this scooter and must perform all of the procedures in this manual. The symbols below are used throughout this owner's manual and on the scooter to identify warnings and important information. It is very important for you to read them and understand them completely. WARNING! Indicates a potentially hazardous condition/situation.
CONTENTS I. INTRODUCTION .......................................................................................................................4 II. SAFETY ........................................................................................................................................5 III. YOUR SCOOTER ......................................................................................................................19 IV. BATTERIES AND CHARGING ...............................................
I. INTRODUCTION SAFETY Welcome to Pride Mobility Products (Pride). The product you have purchased combines state-of the-art components with safety, comfort, and styling in mind. We are confident the design features will provide you with the conveniences you expect during your daily activities. Understanding how to safely operate and care for this product should bring you years of trouble free operation and service.
II. SAFETY PRODUCT SAFETY SYMBOLS The symbols below are used on the scooter to identify warnings, mandatory actions, and prohibited actions. It is very important for you to read and understand them completely. Pinch/Crush points created during assembly. Corrosive chemicals contained in battery. EMI/RFI- This product has been tested and passed at an immunity level of 20 V/m. Explosive conditions exist! Read and follow the information in the owner’s manual. Do not remove anti-tip wheels.
II. SAFETY Do not place the scooter in freewheel mode on a decline or incline. Unlocked and in freewheel mode. Place unit on level ground and stand to one side when changing from drive mode to freewheel mode or freewheel mode to drive mode. Locked and in drive mode. Battery posts, terminals, and related accessories contain lead and lead compounds. Wear goggle and gloves when handling batteries and wash hands after handling.
II. SAFETY Do not use a cell phone, walkie/talkie, laptop, or other radio transmitter while operating. Avoid exposure to rain, snow, ice, salt, or standing water whenever possible. Maintain and store in a clean and dry condition. Removal of grounding prong can create electrical hazard. If necessary, properly install an approved 3-pronged adapter to an electrical outlet having 2-pronged plug access. Do not connect an extension cord to the AC/DC converter or the battery charger.
II. SAFETY Keep your hands away from the tires when driving. Be aware that loose fitting clothing can become caught in drive tires. Battery charger for indoor use only. Disposal and recycling - Contact your authorized Pride Provider for information on proper disposal and recycling of your Pride product and its packaging. Indicates tie-down points on the scooter. 8 www.pridemobility.
II. SAFETY GENERAL MANDATORY! Do not operate your new scooter for the first time without completely reading and understanding this owner’s manual. Your scooter is a state-of-the-art life-enhancement device designed to increase mobility. Pride provides an extensive variety of products to best fit the individual needs of the scooter user.
II. SAFETY Perform the following inspections prior to using your scooter: Check for proper tire inflation. Maintain but do not exceed the psi/bar/kPa air pressure rating indicated on each tire if equipped with pneumatic tires. Check all electrical connections. Make sure they are tight and not corroded. Check all harness connections. Make sure they are secured properly. Check the brakes. Check battery charge. Ensure the manual freewheel lever is in drive mode before sitting on the Travel Scooter.
II. SAFETY When climbing an incline, try to keep your scooter moving. If you must stop, start up again slowly, and then accelerate cautiously. When driving down an incline, do so by setting the speed adjustment dial to the slowest setting and driving in the forward direction only. If your scooter starts to move down the incline faster than you anticipated or desired, allow it to come to a complete stop by releasing the throttle control lever.
II. SAFETY Figure 1. Normal Driving Position Figure 2. Increased Stability Driving Position CORNERING INFORMATION Excessively high cornering speeds can create the possibility of tipping.
II. SAFETY PUBLIC STREETS AND ROADWAYS WARNING! You should not operate your scooter on public streets and roadways. Be aware that it may be difficult for traffic to see you when you are seated on your scooter. Obey all local pedestrian traffic rules. Wait until your path is clear of traffic, and then proceed with extreme caution. STATIONARY OBSTACLES (STEPS, CURBS, ETC.) WARNING! Do not drive near raised surfaces, unprotected ledges, and/or drop-offs (curbs, porches, stairs, etc.).
II. SAFETY FREEWHEEL MODE Your scooter is equipped with a manual freewheel lever that, when engaged, allows the scooter to be pushed. For more information about how to place your scooter into and out of freewheel mode, see III. “Your Scooter.” WARNING! When your scooter is in freewheel mode, the braking system is disengaged. Disengage the drive motors only on a level surface. Ensure the key is removed from the key switch. Stand to the side of the scooter to engage or disengage freewheel mode.
II. SAFETY LIFT/ELEVATION PRODUCTS If you will be transporting your scooter during travel, you may find it necessary to use a vehicle-mounted lift system or elevation product to aid in transportation. Pride recommends that you closely review the warnings, instructions, specifications, and safety information set forth by the manufacturer of the lift/ elevation product before using that product. WARNING! Not all lift systems/elevation products are rated for use with an occupied mobility device.
II. SAFETY MOTOR VEHICLE TRANSPORT Pride recommends that you do not remain seated in your scooter while traveling in a motor vehicle. The scooter should be stowed in the trunk of a car or in the back of a truck or van with the batteries removed and/or properly secured. In addition, all removable scooter parts, including the armrests, seat, and shroud should be removed and/or properly secured during motor vehicle transport.
II. SAFETY POSITIONING BELTS Your authorized Pride Provider, therapist(s), and other healthcare professionals are responsible for determining your requirement for a positioning belt in order to operate your scooter safely. WARNING! If you require a positioning belt to safely operate your scooter, make sure it is fastened securely. PRESCRIPTION DRUGS/PHYSICAL LIMITATIONS The scooter user must exercise care and common sense when operating his/her scooter.
II. SAFETY ELECTROMAGNETIC AND RADIO FREQUENCY INTERFERENCE (EMI/RFI) WARNING! Laboratory tests have shown that electromagnetic and radio frequency waves can have an adverse effect on the performance of electrically-powered mobility vehicles.
III. YOUR SCOOTER TILLER CONSOLE The tiller console houses all of the controls needed to drive your scooter, including the speed adjustment dial, key switch, battery condition meter, status LED, horn buttons, turn signal buttons, accessory switches, and the throttle control lever. See figure 4. Please note that some of the features listed in this section are optional items available only on certain models in the Victory product line.
III. YOUR SCOOTER Status LED The status LED alerts you to electrical problems that may occur with the scooter. The LED remains constantly lit while your scooter is on. If your scooter develops an electrical problem, the status LED will flash a code. See VIII. “Basic Troubleshooting” for flash codes. Horn Buttons These buttons activate a warning horn. Your scooter must be powered up for the horn to be operational. Do not hesitate to use the warning horn when doing so may prevent accident or injury.
III. YOUR SCOOTER Throttle Control Lever This lever allows you to control the forward speed and the reverse speed of your scooter up to the maximum speed you preset with the speed adjustment dial. To Move Forward, use either of the following: Use your left thumb to push the left side of the throttle control lever. Use your right hand fingers to pull back on the right side of the throttle control lever.
III. YOUR SCOOTER REAR COMPONENTS The batteries, anti-tip wheels, motor/transaxle assembly, main circuit breaker (reset button), and the manual freewheel lever are located on your scooter as shown. See figure 7. BATTERY BATTERY MANUAL FREEWHEEL LEVER MOTOR/TRANSAXLE ASSEMBLY ANTI-TIP WHEELS Figure 7. Rear Components Batteries The batteries store electrical energy that powers your scooter. See IV. “Batteries and Charging ” for information on how to charge your scooter batteries.
III. YOUR SCOOTER Main Circuit Breaker (Reset Button) When the voltage in the batteries becomes low or your scooter is heavily strained because of excessive loads, the main circuit breaker may trip to protect the motor and electronics from damage. When the breaker trips, the entire electrical system shuts down. See figure 8. The reset button pops out when the breaker trips. Allow a minute or so for the electronics to “rest.” Push in the reset button to reset the breaker.
III. YOUR SCOOTER SECURING THE SCOOTER Always secure the scooter in a forward-facing position in the vehicle. Attach the four tie-down straps to the designated securement points. See figures 9, 9A, and 9B. Tighten the straps to sufficiently remove all slack. Never attach tie-downs to adjustable, moving, or removable parts of the scooter such as armrests, shrouds, and wheels. These items should be removed.
IV. BATTERIES AND CHARGING BATTERIES AND CHARGING Your scooter requires two long-lasting, 12-volt, deep-cycle batteries that are sealed and maintenance free. They are recharged by an off-board charging system. Charge your scooter’s batteries prior to using it for the first time. Keep the batteries fully charged to keep your scooter running smoothly. READING YOUR BATTERY VOLTAGE The battery condition meter on the tiller console indicates the approximate strength of your batteries using a color code.
IV. BATTERIES AND CHARGING Follow these easy steps to change your batteries safely: 1. Position the front of your scooter close to a standard electrical outlet. 2. Remove the key from the key switch. 3. Make sure that the manual freewheel lever is in the drive position. 4. Plug the 3-pin charger power cord into the off-board charger port. See figures 5 and 11. 5. Extend the charger power cord and plug it into the electrical outlet. We recommend that you charge the batteries for at least 8 to 14 hours. 6.
IV. BATTERIES AND CHARGING How often must I charge the batteries? Two major factors must be considered when deciding how often to charge your scooter’s batteries: All day scooter use on a daily basis. Infrequent or sporadic scooter use. With these considerations in mind, you can determine how often and for how long you should charge your scooter’s batteries. We designed the off-board charger so that it will not overcharge your scooter’s batteries.
IV. BATTERIES AND CHARGING What type and size of battery should I use? We recommend deep-cycle batteries that are sealed and maintenance free. Both AGM and Gel-Cell are deepcycle batteries that are similar in performance. Do not use wet-cell batteries, which have removable caps. WARNING! Corrosive chemicals are contained in batteries. Use only AGM or GelCell batteries to reduce the risk of leakage or explosive conditions. NOTE: Sealed batteries are not serviceable. Do not remove the caps.
IV. BATTERIES AND CHARGING BATTERY TERMINALS UNDER BOOTS BATTERY HARNESS CONNECTIONS Figure 12. Battery Removal/Installation Figure 13. Battery Wiring Diagram NOTE: If you encounter a damaged or cracked battery, immediately enclose it in a plastic bag. Contact your local waste disposal agency or your authorized Pride Provider for instructions on disposal and battery recycling, which is our recommended course of action.
IV. BATTERIES AND CHARGING Follow these steps to properly break in your scooter’s new batteries for maximum efficiency and service life: 1. Fully recharge any new battery prior to its initial use. This charging cycle brings the battery up to about 88% of its peak performance level. 2. Operate your new scooter in familiar and safe areas.
V. OPERATION BEFORE GETTING ONTO YOUR SCOOTER Have you fully charged the batteries? See IV. “Batteries and Charging.” Is the manual freewheel lever in the drive (rearward) position? Never leave the manual freewheel lever pushed forward unless you are manually pushing your scooter. GETTING ONTO YOUR SCOOTER 1. Make certain that the key is removed from the key switch. WARNING! Never attempt to get onto or off of your scooter without first removing the key from the key switch.
V. OPERATION Set the speed adjustment dial to your desired speed. Push or pull the appropriate side of the throttle control lever. The electromechanical disc park brake automatically disengages and the scooter accelerates smoothly to the speed you preselected with the speed adjustment dial. Pull on the left handgrip to steer your scooter to the left. Pull on the right handgrip to steer your scooter to the right. Move the tiller to the center position to drive straight ahead.
VI. COMFORT ADJUSTMENTS TILLER ANGLE ADJUSTMENT WARNING! Remove the key from the key switch before adjusting the tiller or the seat. Never attempt to adjust the tiller or the seat while the scooter is in motion. Your scooter is equipped with an adjustable pivoting tiller. 1. While supporting the tiller, turn the tiller adjustment knob counterclockwise to loosen the tiller. See figure 15. 2. Move the tiller to a comfortable position. 3.
VI. COMFORT ADJUSTMENTS SEAT ROTATION ADJUSTMENT The seat rotation lever will secure the seat into several positions. 1. Push forward on the seat rotation lever to disengage the seat. See figure 18. 2. Rotate the seat to the desired position. 3. Release the lever to secure the seat into place. FRONT-TO-BACK SEAT ADJUSTMENT You can reposition the seat forward or rearward to adjust the distance between the seat and the tiller. 1. Move the seat sliding lever located at the lower left side of the seat outward.
VI. COMFORT ADJUSTMENTS POWER SEAT ADJUSTMENT Your scooter may be equipped with a power seat. The power seat actuator is designed to raise or lower the seat with minimal effort on the part of the operator. The power seat switch is located on the tiller console. WARNING! The power seat is intended for operation only while your scooter is stationary and on a level surface. Its purpose is to aid you in reaching objects. Drive your scooter only with the power seat in the lowest position.
VII. DISASSEMBLY AND ASSEMBLY DISASSEMBLY You can disassemble the scooter into several pieces: the seat, the front section, the rear section, the battery shroud (if equipped), the basket, and the batteries or battery boxes. See figure 20. No tools are required to disassemble or assemble your scooter, but keep in mind that the disassembled sections of the scooter take up more floor space than the assembled unit.
VII. DISASSEMBLY AND ASSEMBLY Frame Separation 1. Arrange the front wheel(s) in a straight forward-facing position. 2. Lower the tiller and tighten the tiller adjustment knob. FRAME RELEASE LEVER NOTE: The pivoting tiller is equipped with a mechanism that will lock the front wheels in place when the tiller is completely lowered and secured. 3. Grasp and lift up on the frame release lever. See figure 22. 4. Lift the front section up until the frame hooks of the front section separate from the rear section.
VIII. BASIC TROUBLESHOOTING Any electromechanical device occasionally requires some troubleshooting. However, most of the problems that may arise can usually be solved with a bit of thought and common sense. Many of these problems occur because the batteries are not fully charged or because the batteries are worn down and can no longer hold a charge. DIAGNOSTIC FAULT CODES The diagnostic fault codes for your scooter are designed to help you perform basic troubleshooting quickly and easily.
VIII. BASIC TROUBLESHOOTING What if my scooter does not move when I engage the throttle control lever? When the manual freewheel lever is pushed forward, the brakes are disengaged and all power to the motor/transaxle assembly is cut. Push rearward on the manual freewheel lever, turn the scooter off, and then turn the scooter on to return to normal scooter operation.
IX. CARE AND MAINTENANCE Your scooter requires a minimal amount of care and maintenance. If you do not feel confident in your ability to perform the maintenance listed below, you may schedule inspection and maintenance at your authorized Pride Provider. The following areas require periodic inspection and/or care and maintenance. TIRE PRESSURE If equipped with pneumatic tires, always maintain the psi/bar/kPa air pressure rating indicated on each tire.
IX. CARE AND MAINTENANCE WHEEL REPLACEMENT If your scooter is equipped with pneumatic tires and you have a flat tire, you can have the tube replaced. If your scooter is equipped with a solid tire insert, either the solid insert or the entire wheel must be replaced depending on the model. Contact your authorized Pride Provider for information regarding replacement wheels for your scooter.
IX. CARE AND MAINTENANCE FUSE REPLACEMENT In the event a fuse should cease to work: 1. Remove the fuse by pulling it out of its slot. 2. Examine the fuse to be sure it is blown. See figures 25 and 25A. 3. Insert a new fuse of the same rating. WARNING! The replacement fuse must exactly match the rating of the fuse being replaced. Failure to use properly rated fuses may cause damage to the electrical system. Figure 25. Working Fuse Figure 25A.
APPENDIX I - SPECIFICATIONS V10 SPECIFICATIONS Model Number SC610V Maximum Allowable Incline 6° (10.5%) Maximum Obstacle Climbing Ability 2 in. (5 cm) Overall Length3 46 in. (116.8 cm) Overall Width3 22.25 in. (56.5 cm) Total Weight Without Batteries6 131 lbs. (59.4 kg) Heaviest Piece When Disassembled Front Section: 53.5 lbs. (24.27 kg) Turning Radius3 42 in. (106.68 cm) Speed (Maximum)1 5.5 mph (8.85 km/h) Range Per Charge1, 2 1 15.5 miles (25 km) Ground Clearance3 4 in. (10.
APPENDIX I - SPECIFICATIONS 39.5 - 42 in. (100.3 - 106.7 cm) 15.25 - 17.75 in. (38.7 - 45.1 cm) 16.5 - 19 in. (42 - 48.25 cm) 4 in. (10.16 cm) 46 in. (116.8 cm) 17 in. (43.18 cm) 18 in. (45.72 cm) Turning Radius 42 in. (106.68 cm) 22.25 in. (56.5 cm) Figure 26. Victory 10 Dimensions 44 www.pridemobility.
APPENDIX I - SPECIFICATIONS V10 PS SPECIFICATIONS Model Number SC610VPS Maximum Allowable Incline 8° (14.1%) Maximum Obstacle Climbing Ability 2 in. (5 cm) Overall Length3 46 in. (116.8 cm) Overall Width3 22.25 in. (56.5 cm) Total Weight Without Batteries6 135.5 lbs. (61.68 kg) Heaviest Piece When Disassembled Front Section 63.5 lbs.(28.9 kg) Turning Radius3 42 in. (106.68 cm) Speed (Maximum) 1 5.5 mph (8.85 km/h) Range Per Charge1,2 1 2 3 4 5 6 15.
APPENDIX I - SPECIFICATIONS 42 - 51.5 in. (106.65 - 130.8 cm) 17 - 23 in. (43.18 - 58.4 cm) 17.25 - 23.25 in. (43.8 - 59.1 cm) 4 in. (10.16 cm) 46 in. (116.8 cm) 17 in. (43.18 cm) 18 in. (45.72 cm) Turning Radius 42 in. (106.68 cm) 22.25 in. (56.5 cm) Figure 27. V10 PS Dimensions 46 www.pridemobility.
SAFETY GUIDELINES WARNING! An authorized Pride Provider or qualified technician must perform the initial setup of this scooter and must perform all of the procedures in this manual. The symbols below are used throughout this owner's manual and on the scooter to identify warnings and important information. It is very important for you to read them and understand them completely. WARNING! Indicates a potentially hazardous condition/situation.
V10 *INFMANU4437*
