3 & 4 Wheel Scooters Owners Manual Exeter, PA St. Catharines, ON 1-800-800-8586 www.pridemobility.
S A F E T Y G U I D E L I N E S Read and follow all of the instructions in this manual before you attempt to operate your scooter for the first time. If you are unable to understand any of this information or require additional assistance for set-up, contact your local Pride Provider or call the Pride Tech Service Department at 1-800-800-8586. The following symbols are used throughout this Owners Manual to identify warnings and cautions.
C O N T E N T S I. INTRODUCTION ........................................................................................................................ 5 II. SAFETY ......................................................................................................................................... 6 III. EMI/RFI .......................................................................................................................................... 9 IV. SPECIFICATIONS .............................
C O P Y R I G H T Pride cannot be held responsible for any damage or injury incurred due to improper or unsafe use of a Shuttle Scooter. Nor can Pride be held responsible for any damage or injury incurred during or resulting from attempts to follow the instructions and recommendations set forth in this owner's manual or in any of the instructions displayed on or accompanying the product itself.
I . I N T RO D U C T I O N Welcome to Pride Mobility Products Corporation (Pride). Congratulations on the purchase of your new Shuttle Scooter. The Shuttle design combines the most advanced state-of-the-art components with modern, attractive styling. We are certain that the design features and trouble-free operation of your new Shuttle Scooter will add convenience to your daily living. At Pride, your safety is important to us.
I I . S A F E T Y As you begin to use your Shuttle during your daily activities, you will encounter situations that, at first, may require some practice to negotiate on your scooter. Simply take your time as you operate your Shuttle and you will soon be in full and confident control as you maneuver through doorways, on and off of elevators, up and down ramps, and over moderate terrain. DOORS n Determine if the door opens toward or away from you.
I I . S A F E T Y These tests were conducted with the Shuttles seat in the highest position and adjusted backward on the seat base to its farthest rearward position. Use this information as a guideline. Your Shuttles ability to travel up inclines is affected by your weight, your scooters speed, your angle of approach to the incline, and your scooter setup. n When you approach an incline, it is best to lean forward. See figures 3 and 4.
I I . S A F E T Y SAFETY PRECAUTIONS n Do not operate your new Shuttle for the first time without completely reading and understanding this owners manual. n Do not carry passengers on your Shuttle. n Do not leave the key in the switch when your Shuttle is unattended. n Make certain that the seat is locked into place and that the key is removed from the key switch before getting on or off of your Shuttle. Make certain that the seat is in a locked position when you are operating your Shuttle.
I I I . E M I / R F I EMI/RFI WARNINGS Laboratory tests performed by the Food and Drug Administration (FDA) have shown that radio waves can cause unintended motion of electric scooters. Radio waves are a form of electromagnetic energy (EM). When electromagnetic energy adversely affects the operation of an electrical device, that adverse effect is called Electromagnetic Interference (EMI) or Radio Frequency Interference (RFI).
I I I . E M I / R F I What is the FDA doing about the problem? The FDA has written to the manufacturers of electric scooters and requested that those manufacturers test their new models of scooters to be certain that they provide a reasonable degree of resistance against EMI/ RFI. The FDA has stated that all newly manufactured models of electric scooters should have a resistance level of at least 20 V/m.
I V. Model Numbers Length Width Tires Weight Capacity Battery Type (Batteries not included) Horsepow er Charger Speed (Maximum) Maximum Grade Range Turning Radius Body Colors Seating S P E C I F I C AT I O N S Shuttle 3: SC100 Shuttle 4: SC140 Shuttle 3: 46.5 in. Shuttle 4: 47.5 in. 24in. Type: Pneumatic Front: 3.5 in. x 10 in. Rear: 3.5 in. x 10 in. 300 lbs. Maximum Two 12-volt, 32 AH, U-1 type, SLA (sealed lead-acid) 1.1 hp (peak) Onboard 3-amp charger Variable up to 5.
I V. S P E C I F I C AT I O N S 13" 9" 85˚ 34.5" - 36.5" 16.5"- 18.5"" 4.5" FIGURE 5. SHUTTLE DIMENSIONS 46.5" 3 Wheel Shuttle 18" 47.
V. D E S C R I P T I O N Your Shuttle is a motorized electric scooter designed to enhance your personal mobility. Your Shuttle is an indoor/outdoor scooter that was designed to travel primarily on smooth surfaces such as sidewalks, roads, parking lots, floors, and driveways. For easy transportation or storage, you can disassemble your Shuttle into five components. See figure 6. FRONT SECTION SEAT REAR SECTION BATTERY BOXES FIGURE 6.
V. D E S C R I P T I O N Do not expose the control console assembly to moisture. In the event that the console does become exposed to moisture, do not attempt to operate your Shuttle until the control console assembly has thoroughly dried. Key Switch n Fully insert the key into the key switch to power up (turn on) your Shuttle. n Pull the key out to power down (turn off) your Shuttle.
V. D E S C R I P T I O N REAR SECTION The onboard battery charger (not shown), the charger cord, the battery charger fuse (not shown), the batteries, the electronic controller assembly, the main circuit breaker, the manual freewheel lever, the anti-tip wheels, and the motor/transaxle assembly are located on the rear section of your Shuttle. See figures 8 and 8A.
V. D E S C R I P T I O N Electronic Controller Assembly (not shown) The electronic controller assembly is located behind the batteries and at the forward left corner of the Shuttles rear section. This assembly receives electrical signals from the control console assembly controls and sends power to the motor, the brakes, and the optional lighting system.
VI. BATTERIES AND CHARGING Your Shuttle uses two long-lasting, 12-volt, deep-cycle batteries that are sealed and maintenance-free. They are recharged by an onboard 3-amp charging system designed for ease of use and convenience. n Charge your Shuttles batteries prior to using it for the first time. n Keeping your batteries fully charged is one of the best ways to keep your Shuttle running trouble-free. Follow these easy steps to charge your batteries safely: 1.
VI. BATTERIES AND CHARGING With these considerations in mind, you can determine just how often and for how long you should charge your Shuttles batteries. We designed the onboard charger so that it will not overcharge your scooters batteries (do not charge them for more than 24 consecutive hours). However, you may encounter some problems if you do not charge your batteries often enough and if you do not charge them on a regular basis.
VI. BATTERIES AND CHARGING To change a battery in your Shuttle: 1. Remove the seat. See figure 14. 2. Unstrap the batteries from the floorboard. 3. Remove the top of the battery case. 4. Disconnect the battery cables from the battery terminals. See figure 9. 5. Remove the old battery. 6. Place a new battery in the battery well. 7. Connect the red battery cable to the positive (+) battery terminal. 8. Connect the black battery cable to the negative (-) battery terminal. 9.
VI. BATTERIES AND CHARGING 5. Fully recharge the batteries again. 6. After four or five charging cycles, the batteries will be able to receive a charge of 100% of their peak performance level and will be able to last for an extended period of time. How can I ensure maximum battery life? Fully charged deep-cycle batteries will provide reliable performance and extended battery life. Keep your Shuttles batteries fully charged whenever possible.
V I I . O P E R AT I O N GETTING ON YOUR SHUTTLE 1. Make certain that the key is removed from the key switch. 2. Stand at the side of your Shuttle. 3. Push down on the seat lock lever and rotate the seat until it is facing you. 4. Make certain that the seat is locked securely in position. 5. Position yourself comfortably and securely in the seat. 6. Push down on the seat lock lever and rotate the seat until you are facing forward. 7. Make certain that the seat is locked securely in position. 8.
V I I . O P E R AT I O N GETTING OFF OF YOUR SHUTTLE 1. Bring your Shuttle to a complete stop. 2. Make certain that the key is removed from the key switch. 3. Push down on the seat lock lever and rotate the seat until you are facing toward the side of your Shuttle. 4. Make certain that seat is locked securely in position. 5. Carefully and safely get out of the seat and stand to the side of your Shuttle. 6.
V I I I . C O M F O RT A D J U S T M E N T S TILLER ANGLE ADJUSTMENT WARNING! Remove the key before adjusting the tiller. Never attempt to adjust the tiller while the shuttle is in motion. You can adjust the tiller to three positions. The tiller adjustment lever locks the tiller in place. See figure 10. 1. Squeeze the tiller lock lever. 2. Reposition the tiller to one of the three possible settings. The tiller may be lowered to the center of the floorboard and locked in place for storage. See IX.
V I I I . C O M F O RT A D J U S T M E N T S FRONT-TO-BACK SEAT ADJUSTMENT You can reposition the Shuttles seat forward or rearward to adjust the distance between the seat and the tiller. See figure 12. 1. Remove the seat from your Shuttle. See figure 14 2. Remove the four bolts that fasten the seat to the seat platform. 3. Align the seat platform with the desired set of holes on the seat. 4. Reinstall the four bolts securely.
IX. D I S A S S E M B LY A N D A S S E M B LY The Shuttle 3 (three-wheel) and the Shuttle 4 (four-wheel) are identical in disassembly and assembly. No tools are required. Always disassemble or assemble your Shuttle on a level, dry surface with sufficient room for you to work and move around your scooter. Keep in mind that the disassembled sections of the Shuttle will take up more floor space than the assembled Shuttle. DISASSEMBLY 1. Remove the key from the key switch. See V. Description. 2.
IX. D I S A S S E M B LY A N D A S S E M B LY FIGURE 14. SEAT REMOVAL FIGURE 15. BATTERY HARNESS FIGURE 16. BATTERY REMOVAL / REPLACEMENT FIGURE 17. TILLERS LOWEST POSITION UNLOCKED POSITION FIGURE 18. FRAME LOCK LEVER FIGURE 19. FRAME SEPARATION FIGURE 20. FRONT-TO-REAR CABLE CONNECTOR 26 FIGURE 21.
X . O P T I O NA L AC C E S S O R I E S OPTIONAL ACCESSORIES For information concerning these accessories, see your authorized Pride provider or call at (570) 655-5574.
X I . BA S I C T R O U B L E S H O OT I N G Any electromechanical device will occasionally require some troubleshooting. However, most of the problems that may arise can usually be solved with a bit of thought and common sense. Many of these problems occur because the batteries are not fully charged or because the batteries are worn down and can no longer hold a charge. What if all the systems on my Shuttle seem to be dead? n Make certain that the key is fully inserted in the key switch.
XII. CARE AND MAINTENANCE Your Shuttle requires a minimal amount of care and maintenance. If you do not feel confident in your ability to perform the maintenance listed below, you may schedule inspection and maintenance at your authorized Pride provider. The following areas require periodic inspection and/or care and maintenance. TIRE PRESSURE: n For optimum scooter performance we recommend that the tire pressure be maintained at 30 psi.
XII. CARE AND MAINTENANCE AXLE BEARINGS AND THE MOTOR/TRANSAXLE ASSEMBLY: n These items are all prelubricated, sealed, and require no subsequent lubrication. TO REPLACE THE MOTOR BRUSHES: 1. Disassemble the Shuttle. 2. Place the rear frame assembly on something that will support it. 3. Remove the four Phillips-head screws from the rear shroud. 4. Use a small right angle screwdriver to unscrew the top motor brush cap. See fgure 22. 5. Remove the motor brush. 6. Examine the motor brush.
X I I I . W A R R A N T Y THREE-YEAR LIMITED WARRANTY Structural frame components; including platform, fork, seat post, and frame. Drive train; including transaxle, motor, and brake. First year: 100% replacement of parts cost Second year: 67% replacement of parts cost Third year: 50% replacement of parts cost THREE-YEAR WARRANTY EXCEPTIONS Transaxle: In cases where there is an increase in the operational noise level, the warranty will not apply.
X I I I . W A R R A N T Y There is no other express warranty. Implied warranties, including those of merchantability and fitness for a particular purpose, are limited to one (1) year from the date of original purchase and to the extent permitted by law. Any and all implied warranties are excluded. This is the exclusive remedy. Liabilities for consequential damages under any and all warranties are excluded.
N OTES Shuttle 33
N OTES 34 Shuttle
