INSTALLATION INSTRUCTIONS Polaris™ Universal Projector Mount Model: MAG-PRO/MAG-PRO-W NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada Phone: 1.800.368.9700 Fax: 1.800.832.4888 Other Locations Phone: (001).714.632.7100 Fax: (001).714.632.
MAG-PRO/MAG-PRO-W Contents Weight Limit...................................................................................................................................................................... 2 Warning Statements......................................................................................................................................................... 2 Installation Tools...............................................................................................................
MAG-PRO/MAG-PRO-W Installation Tools The following tools may be required depending upon your particular installation. They are not included. 2 1 Tape Measure Pencil Phillips Tip Screwdriver M3 Security Wrench (Supplied) M5 Security Wrench (Supplied) Protective Eyewear Ladder Parts List Make sure your Premier Mounts product has the following hardware and components before beginning installation.
MAG-PRO/MAG-PRO-W Features Congratulations on the purchase of your new Premier Mounts Polaris™ Universal Projector Mount. Your MAG-PRO/MAG-PRO-W Mount may be secured to a1-½˝ NPT. The Polaris™ features our exclusive MagnaGuide™ Technology which assists the installer for quicker installation times and peace of mind. Please read these installation instructions once thoroughly before attempting to install your Premier Mounts product.
MAG-PRO/MAG-PRO-W Attaching the MAG-PRO/MAG-PRO-W Mount to the Projector Locate the mounting points on the bottom of the projector (see arrows to the right). Proceed to the “Attaching the Projector Plate” section. Attaching the Projector Plate Selecting the Mounting Hardware Insert a small straw or toothpick into the threaded inserts found on the bottom or top of the projector. ®® Use a pencil to mark the depth of the threaded insert on the small straw or toothpick.
MAG-PRO/MAG-PRO-W Multiple Mounting Point Installation Step 1 Locate the projector’s mounting points. ®® Position an appropriate number of mounting legs on the projector. The four mounting legs come pre-installed. If there are less than four thread inserts on the projector, remove the appropriate number of mounting legs. The number and placement of mounting points on projectors varies between projector manufacturers.
MAG-PRO/MAG-PRO-W Step 3 If the mounting legs need to be leveled, rotate the leveling barrels to level the mounting bracket. ®® To raise the mounting legs, rotate the leveling barrel clock-wise. To lower the mounting leg, rotate the leveling barrel counter clock-wise. Raise or lower each of the mounting legs, by rotating the leveling barrels, until all of the mounting legs are at an equal height. • Lower the mounting leg by rotating the leveling barrel counter-clockwise.
MAG-PRO/MAG-PRO-W Step 5 Position the legs accordingly for best configuration. ®® ¯¯ You may raise or lower each leg independently by turning the leveling barrels. Secure the legs to the projector plate by screwing M6 x 12mm security screws into the M6 square nut (do not overtighten) on the mounting legs. Verify the position of the integrated sliding M6 square nut in the mounting leg relative to a nearby slot on the Projector Plate.
MAG-PRO/MAG-PRO-W Single Mounting Point Installation A single ¼-20 x 5/16″ screw must be used to attach the Projector Plate to the projector if your projector has only one mounting point. Do not overtighten the ¼-20 x 5/16″ screw. Proceed to the “Installing the MAG-PRO/MAG-PRO-W Mount” section. Installing the MAG-PRO/MAG-PRO-W Mount Step 1 The Polaris™ MAG-PRO/MAG-PRO-W may be attached to 1-½˝ standard threaded pipe (NPT), or one of Premier Mounts adjustable-height ceiling adapters.
MAG-PRO/MAG-PRO-W Step 2 Secure the MAG-PRO/MAG-PRO-W by tightening ®® the set screw with the M3 security Allen wrench (supplied). Route any cables up through the 1-½˝ NPT and into the ceiling structure. If the PP-FCTA Ceiling Mount is to be used, the CLS must first be threaded into the MAG-PRO/MAG-PRO-W. For further installation instructions, please refer to the PP-FCTA installation manual. Set Screw M3 Security Wrench Step 3 Slowly raise the projector toward the upper assembly.
MAG-PRO/MAG-PRO-W MAG-PRO/MAG-PRO-W Mount Adjustment Step 1 After the projector has been installed, you may need to adjust it. To adjust the projector: Loosen the M5 set screw using the M5 Allen wrench (both sides). ®® Adjust the projector to the correct position. Firmly grasp the projector in both hands, and tilt either forward or backward to adjust the level. -OR- M5 Set Screw ¯¯ Firmly grasp the projector in both hands and rotate side to side for orientation adjustment.
MAG-PRO/MAG-PRO-W Technical Specifications All measurements are in inches [millimeters]. Page 12 Visit the Premier Mounts website at http://www.mounts.
MAG-PRO/MAG-PRO-W Warranty PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product. The limited warranty is valid only for the original purchaser of the product. What Premier Mounts Will Do At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is defective.
