IPM-700 Series iPad™ Wall Mount INSTALLATION INSTRUCTIONS IPM-700 IPM-710 IPM-720 IPM-730 CREATING POSITIVE CUSTOMER EXPERIENCES 9531-056-081-00
IPM-700 Series Contents Warning Statements.................................................................................................................................................. 2 Installation Tools........................................................................................................................................................ 3 Parts List.........................................................................................................................................
IPM-700 Series Installation Tools The following tools may be required depending on your installation. 3/16" Drill Bit Level Electronic Stud Finder 3/16" Concrete Drill Bit Hand Held Drill 2 1 Pencil Phillips Tip Screwdriver Tape Measure Hammer Drywall Saw Parts List Make sure none of the Premier Mounts parts are missing and/or damaged before beginning installation. If there are, stop the installation and call Premier Mounts at (800) 368-9700.
IPM-700 Series Features The IPM-700 Series of secure wall mounting frames is perfect for turning the iPad™ into a compact interactive display for digital signage or control. This decorative and easy-to-install wall mount prevents unauthorized access and does not obstruct reception to WiFi networks.
IPM-700 Series Installing to a Wall Are you installing the IPM-700 to a wood stud, or drywall or concrete? If Wood Stud, continue to the “Wood Stud Installation” section below. THIS SIDE UP X If Drywall or Concrete, go to the “Drywall or Concrete Installation” section on page 6.
IPM-700 Series Installing to a Wall (cont’d) Drywall or Concrete Installation THIS SIDE UP Are you installing the IPM-700 with a GB-INWAVP GearBox™ on a drywall surface? X X CUT THIS LINE IF USING GB-INWAVP CUT THIS LINE IF USING GB-INWAVP If Yes, go to the “With GB-INWAVP” section on page 7. CL CUT THIS LINE IF USING GB-INWAVP If No, continue to the “Without GB-INWAVP” section below. CUT THIS LINE IF USING GB-INWAVP X Do not use the IPM-700 Series with GB-INWAVP on concrete.
IPM-700 Series Installing to a Wall (cont’d) With GB-INWAVP If you are using the IPM-700 Series with Premier Mounts’ In-Wall A/V and Power GearBox™ (GB-INWAVP) (sold separately), install the GB-INWAVP first. Then install the IPM-700 Series mount over it for easy cable and accessory management. These instructions are for drywall installations only.
IPM-700 Series Installing to a Wall (cont’d) Step 2 ➊➊ Cut a hole in the paper template where it says “CUT ➌➌ THIS SIDE UP X X CUT THIS LINE IF USING GB-INWAVP CUT THIS LINE IF USING GB-INWAVP ➋➋ THIS LINE”. Cut or punch out the corner screw holes on the paper template (marked “X”) (Figure 1). Place the paper template at the desired location between the studs (Figure 2). You may install the back plate and GB-INWAVP in portrait or landscape orientation.
IPM-700 Series Installing to a Wall (cont’d) Step 3 Use a drywall saw to remove the drywall in the area you marked in step 2 (Figure 3). Avoid cutting electrical wires, water pipes, or gas lines. Remove a small piece of drywall and use a flashlight to look around for these hazards in the area in which you will be cutting. Once you have located any hazards, proceed to carefully remove the rest of the drywall.
IPM-700 Series Installing to a Wall (cont’d) Step 6 ➊➊ Insert one (1) in-wall clamp through the T-notch and ➋➋ pull it forward. Fasten with one (1) 6-32 x 2˝ pan head screw. Do not overtighten the 6-32 x 2˝ pan head screw. Note the proper orientation for the in-wall clamp. ➌➌ Repeat steps 1 and 2 for the remaining in-wall clamp. Continue to the “Outlet Box Installation” section on page 11.
IPM-700 Series Installing to a Wall (cont’d) Outlet Box Installation Installation of electrical power to your GB-INWAVP should be performed by a qualified professional electrician. Improper installation and handling of live electrical wires can result in property damage and severe personal injury. The 110 volt duplex receptacle, flexible aluminum conduit, and electrical wiring are not included with your GB-INWAVP.
IPM-700 Series Installing to a Wall (cont’d) Installing the IPM-700 Series Over the GB-INWAVP ➊➊ Drill pilot holes at the marked locations using a 3/16" drill bit. ➋➋ Insert four (4) #10 screw anchors into the four holes in the wall (Figure 1). If necessary, use a hammer to lightly tap each screw anchor into the wall. ➌➌ Place the back plate against the wall, making sure the corner screw holes align with the screw anchors.
IPM-700 Series Installing the iPad™ If you are using an iPad2™, attach two (2) rubber edge trims to the long tabs of the back plate as shown (Figure 1). Then attach four (4) adhesive-backed bumpers to the notches on the back plate (Figure 2). ➊➊ Place the iPad™ on the back plate by easing it ➋➋ ➌➌ against the top brackets, then the bottom brackets (Figure 3). Center the iPad™ on the back plate.
IPM-700 Series Attaching the Cover ➊➊ Use your fingers to pre-install two (2) M3 x 12mm set screws to the bottom of the front plate (Figure 1). ➋➋ Hook the front plate over the top of the back plate, ➌➌ then ease it over the bottom of the back plate (Figure 2). Use the M1.5 Allen wrench to tighten the set screws. ➊➊ ➋➋ Figure 1 M3 x 12mm Set Screw Figure 2 Technical Specifications All measurements are in inches [millimeters]. 7.94 202 6.16 156 5.00 127 5.91 150 7.85 199 12.12 308 10.00 6.
IPM-700 Series IPM-700 Series Warranty PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product. The limited warranty is valid only for the original purchaser of the product.
