INSTALLATION INSTRUCTIONS Fine Tune Projector Mount Model: FTP / FTPW NORTH AMERICA EUROPE AUSTRALIA AND OCEANIA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada Phone: 1.800.368.9700 Fax: 1.800.832.4888 Other Locations Phone: (001).714.632.7100 Fax: (001).714.632.
Fine Tune Projector Mount Contents Weight Limit. ............................................................................................................................................................. 2 Warning Statements. ................................................................................................................................................ 2 Installation Tools. ...................................................................................................................
Fine Tune Projector Mount Installation Tools The following tools may be required, dependent upon your particular installation. These tools are not provided by Premier Mounts, but you can purchase them at your local hardware store.
Fine Tune Projector Mount Parts List (cont’d) Mounting Hardware Lock-It™ Security Hardware Pack Your Premier Mounts Fine Tune Projector Mount comes with the option of using Lock-It™ Security Screws. Simply replace any of the Phillips head screws with the corresponding sized Lock-It™ Security Screws and tighten using the appropriate size Allen wrench. When you see the graphics below associated with a step, you have the option of using the standard mounting hardware or the Lock-It Security hardware.
Fine Tune Projector Mount Features Multiple Mounting Options You can install your Fine Tune Projector mount to 1½˝ NPT pipe or a ceiling stud. Lock-It™ Security Hardware Protect your projector by installing specialized hardware at critical mounting points. Mounting Legs Both long and short mounting legs, combined with the numerous Universal Projector Plate Mounting Slots, allow for near infinite mount configurations.
Fine Tune Projector Mount Installing the Fine Tune Projector Mount Introduction The Fine Tune Projector Mount may be secured to either a 1½˝ standard threaded pipe (NPT), a Premier Mounts optional ceiling adapter, or a single ceiling stud. If using an optional Premier Mounts adapter, please refer to the installation instructions that come with each adapter on the proper installation of that product.
Fine Tune Projector Mount Installing the Fine Tune Projector Mount (cont’d) Step 2 Attach a 6˝ or longer socket wrench extension onto a socket wrench. Insert the end of the socket wrench extension into the center of the Installation Disk, then insert the Installation Disk into the underside of the FTP Dome. Note the arrow inscribed inside of the FTP Dome.
Fine Tune Projector Mount Installing the Fine Tune Projector Mount (cont’d) Wood Stud Installation Step 1 Use a stud finder to locate a ceiling stud closest to your desired installation location. Identify the center of the ceiling stud. Use a pencil to mark the location of the ceiling stud center. CeStud nte r Step 2 Place the Installation Disk against the ceiling with the mounting holes aligned with the center of the ceiling stud.
Fine Tune Projector Mount Installing the Fine Tune Projector Mount (cont’d) Step 4 Insert the Installation Disk into the underside of the FTP Dome. Note the arrow inscribed inside of the FTP Dome; make sure that it is pointed in the same direction that your projector will be pointed. Inscribed Arrow FTP Dome as Viewed from Below Step 5 Insert one (1) #14 x 3˝ screw through each of the holes in the bottom of the Installation Disk and into the pilot holes.
Fine Tune Projector Mount Attaching the Universal Projector Plate Selecting the Mounting Hardware Insert a small straw or toothpick into the thread inserts found on the bottom or top of the projector. Use a pencil to mark the depth of the thread insert on the small straw or toothpick , as shown in Figure 1. Insert the small straw or toothpick into the remaining thread inserts to compare and verify their depth. Locate the correct diameter screw for the thread insert.
Fine Tune Projector Mount Attaching the Universal Projector Plate (cont’d) Multiple Mount Point Installation Step 1 Locate the projector’s mount points. Position an appropriate number of mounting legs on the projector. You can use any combination of three (3) or more long mounting legs and short mounting legs, depending on the number and location of the thread inserts on your projector. The number and placement of mount points on projectors varies between projector manufacturers.
Fine Tune Projector Mount Attaching the Universal Projector Plate (cont’d) Step 3 Raise or lower each of the mounting legs, by rotating the leveling barrels, until all of the mounting legs are at an equal height. • Lower the mounting leg by rotating the leveling barrel counter-clockwise. • Raise the mounting legs by rotating the leveling barrel clockwise. Step 4 Identify the projector’s approximate front-to-back center of gravity.
Fine Tune Projector Mount Attaching the Universal Projector Plate (cont’d) Step 6 Tighten the mounting screws to the projector. Do not overtighten the mounting screws. Step 7 Attach the Universal Projector Plate to each of the mounting legs by inserting and tightening one (1) M6 x 12mm screw through the Universal Projector Plate into the M6 square nut on each of the mounting legs. Do not overtighten the mounting screws. You can use either the standard Phillips head or Lock-It™ security hardware.
Fine Tune Projector Mount Securing the Quick Set Base You had the option of installing Lock-It™ security hardware during several of the previous steps. You may also exchange the screws which secure the Universal Projector Plate to the Quick Set Base. Remove the four (4) Phillips head M6 x 8mm screws which secure the Quick Set Base to the Universal Projector Plate. Replace each M6 x 8mm Phillips head screw with one (1) M6 x 8mm Security screw. Tighten all screws.
Fine Tune Projector Mount Alignment & Fine-Tuning Yaw Yaw can be adjusted up to 20° left and 20° right from center. Adjust the projector’s yaw by turning control ... ...clockwise to pivot the front to the right. ...counter-clockwise to pivot the front to the left. Each full revolution of the control adjusts the yaw by 4°. Pitch Pitch can be adjusted 15° down and 5° up from level. Adjust the projector’s pitch by spinning control ... ...right to pitch the front down. ...left to pitch the front up.
Fine Tune Projector Mount Locking in the Adjustments After you have finalized your yaw, pitch, and roll adjustments, you can lock them in to prevent them from being accidentally changed. FTP Support Sphere Finger-tighten the M5 x 16mm Phillips screw until it makes firm contact with the FTP Support Sphere. Use a Phillips head screwdriver to tighten the M5 x 16mm Phillips screw on the side of the FTP Dome to lock the yaw, roll and pitch adjustments.
Fine Tune Projector Mount Technical Specifications All measurements are in inches. Installation Instructions Visit the Premier Mounts website at http://www.mounts.
Fine Tune Projector Mount Warranty PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product. The limited warranty is valid only for the original purchaser of the product.
