INSTALLATION INSTRUCTIONS Rotary Tilt Mount Model: RTM-L NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada – Phone: 800-368-9700 Fax: 800-832-4888 EUROPE Swallow House, Shilton Industrial Estate, Shilton, Coventry, England CV79JY Phone: +44 (0) 2476 614700 Fax: +44 (0) 2476 614710 Other Locations – Phone: (001)-714-632-7100; Fax: (001)-714-632-1044 ©Premier Mounts 2008 9531-009-011-03 AUSTRALIA, NEW ZEALAND, OCEANIA (DISTRIBUTOR) P.O.
RTM-L Table of Contents Warning Statements Parts List Installation Tools Thread Depth Indicator Mount Installation Universal Mounting Bracket Installation Display Orientation Tilt Positioning Optional Configurations Technical Specifications Security Pack (Optional) Warranty 2 3 3 6 7 8 10 10 11 11 12 13 Warning Statements PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS SHOULD BE READ AND COMPLETELY UNDERSTOOD.
RTM-L Parts List This wall mount is shipped with all proper installation hardware and components. Make sure that none of these parts are missing and/or damaged before beginning installation. If there are parts missing and/or damaged, please stop the installation and contact Premier Mounts (800-368-9700).
RTM-L M4 x 16 (Qty 8) M6 x 20 (Qty 8) (Qty 8) M4 x 25 (Qty 8) M6 x 30 M5 x 12 (Qty 8) M6 x 45 M5 x 16 (Qty 8) M8 x 20 M5 x 20 M5 x 25 (Qty 8) M8 x 25 (Qty 8) (Qty 8) M8 x 30 (Qty 8) (Qty 8) M8 x 35 M8 x 45 M8 x 70 Page 4 (Qty 8) (Qty 8) M5 x 50 M6 x 16 (Qty 8) (Qty 8) (Qty 8) (Qty 4) Installation Instructions
RTM-L The nylon spacers may be stacked to achieve proper spacing.
RTM-L Thread Depth Indicator 1. Insert the thread depth indicator (supplied) through the thread inserts found on the back of the flat panel to make sure the inserts measure the same full depth and mark it (Figure 1). 2. Locate the correct diameter screw for the thread insert. Compare your marking to the screws (supplied). 3. If your selected screw is longer than the marking on the thread depth indicator, DO NOT USE this screw. 4. The screw length must not bypass the marking.
RTM-L Mount Installation The installation instructions that are contained in this manual refer only to the RTM-L. The installation instructions for the various bases that are used with the RTM-L will be included with those products. Prior to installing the RTM-L, the mounting configuration must already be assembled (base, support poles, etc.). Mounting Block Set Screws Cradle Support Poles 1. Slide the mounting block over and down the support poles. Installation Instructions 2.
RTM-L Universal Mounting Bracket Assembly 1. 2. Place the universal bracket bar and the universal brackets on a flat surface. Slide the universal brackets onto the universal bracket bar (as shown below) with the set screws facing up. At this time, do not tighten the set screws that are located on the universal bracket. If you havean un-even mounting surface, or a recessed mounting point, place the appropriately sized nylon washer between the display and the universal mounting brackets (page 5). 3.
RTM-L 6. Lower the universal bracket bar and display into the cradle (as to the left). The circular portion of the universal bracket bar must rest inside the nylon sleeve. If seated improperly, the operation of the RTM-S will be hindered and the nylon sleeve will become damaged. Nylon Sleeve Knurl Knob Mounting Points (a knurl knob may be placed in either mounting hole M6 x 12mm Security Head and M6 Lock Washer Mounting Points (a security screw may be placed in either mounting hole). 7. 8. 9.
RTM-L Display Orientation The RTM-L will allow the user to adjust the display a full 360°. BEFORE ROTATING THE RTM-L, MAKE SURE THAT THE M6 KNURL KNOB IS SECURELY FASTENED TO THE RTM-L. ALSO, PLEASE MAKE SURE YOU ALLOW ENOUGH CABLE AND WIRE CLEARANCE FOR FULL ROTATION. 1. To adjust the RTM-L, rotate the display either clockwise or counter-clockwise. 2. Tilt Positioning Tighten the two Phillips head locking screws. The RTM-L is shipped with the hand crank in the storage position.
RTM-L Optional Configurations PSD-TS PSD-BW PSD-EB Technical Specifications All measurements are in inches (mm).
RTM-L Lock-It™ Security Hardware Pack The RTM-L is shipped with a safety knurl knob already installed. If the user decides to incorporate the optional security hardware, the following steps will show the user how to effectively remove the safety knurl knob and install the optional Lock-It™ hardware kit. The M6 security head screw will be installed after the RTM-L has been fully assembled. Installation of the M6 security head screw prior to completing assembly will not allow the RTM-L to function properly.
RTM-L Warranty PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product. The limited warranty is valid only for the original purchaser of the product. What Premier Mounts Will Do At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is defective.
