P4263TP Portrait Tilting Mount for 42″ to 63″ Flat-Panels INSTALLATION INSTRUCTIONS CREATING POSITIVE CUSTOMER EXPERIENCES 9531-210-021-01
P4263TP Contents Weight Limit............................................................................................................................................................................................................ 2 Warning Statements............................................................................................................................................................................................... 2 Installation Tools.............................................
P4263TP Installation Tools The following tools may be required, dependent upon your particular installation. These tools are not provided by Premier Mounts, but you can purchase them at your local hardware store.
P4263TP Parts List (cont’d) Mounting Hardware M4 x 16mm Screw (Qty 6) M8 x 16mm Screw (Qty 6) M4 x 25mm Screw (Qty 6) M8 x 25mm Screw (Qty 6) M4 x 30mm Screw (Qty 6) M8 x 30mm Screw (Qty 6) M5 x 16mm Screw (Qty 6) M8 x 45mm Screw (Qty 6) M5 x 25mm Screw (Qty 6) M8 x 70mm Screw (Qty 4) M5 x 30mm Screw (Qty 6) M6 x 16mm Screw (Qty 6) M6 x 25mm Screw (Qty 6) M6 x 30mm Screw (Qty 6) M6 x 45mm Screw (Qty 6) Page 4 Visit the Premier Mounts website at http://www.premiermounts.
P4263TP Features Leveling Screws Allows for leveling adjustments of the flat panel after mounting. Cable/Electrical Cut Out A large cut out on the wall plate allows for easy cable access and power distribution installations. Directional Mounting Arrow Directional Mounting Arrow lets you know which edge is up. Adjustable Tilt 8° of continuous tilt for the perfect viewing angle. Low Profile Design Holds the flat panel less than 1″ from the wall.
P4263TP Installing the Wall Plate Introduction Directional Mounting Arrow The Directional Mounting Arrow stamped into the top of the P4263TP wall mount indicates which edge is the top. Mounting Safety Two people are recommended to for the installation of this mount. Determining the Mounting Surface If you will be installing your P4263TP mount to wood studs, proceed to the “Wood Stud Installation” section.
P4263TP Installing the Wall Plate (cont’d) Step 3 Drill a “pilot hole” in the center of the upper right mark using a ¼″ drill bit and power drill. Only use a ¼″ drill bit when drilling the pilot holes. Step 4 ➊➊ Place the wall plate against the wall and align it with ➋➋ the pilot hole. Insert one (1) 5/16″ x 3″ lag bolt and one (1) 5/16″ washer into the upper right mounting hole and tighten using a socket wrench and ½″ socket. Do not overtighten the lag bolt. Step 5 ➊➊ Level the wall plate.
P4263TP Installing the Wall Plate (cont’d) Step 7 ➊➊ Insert one (1) ➋➋ /16″ x 3″ lag bolt and one (1) 5/16″ washer into each pilot hole Tighten all lag bolts using a socket wrench and ½″ socket. 5 Do not overtighten the lag bolts when attaching the mount to the wall. Improper installation may result in personal injury or property damage. Proceed to the “Installing the Mounting Bracket” section. Concrete Installation The supplied 5/16″ concrete wedge anchors must be used for concrete installation.
P4263TP Installing the Wall Plate (cont’d) Step 3 ➊➊ Insert a concrete wedge anchor into each hole. ➋➋ ➌➌ If necessary, lightly tap each concrete wedge anchor into place with a hammer. Remove the nuts and washers from all four (4) concrete wedge anchors. Replace the washers which you removed from the concrete wedge anchors with the 5/16″ washers shown in the parts list on Page 3. Step 4 ➊➊ Place the wall plate against the wall over the ➋➋ threaded shafts of the concrete wedge anchors.
Installing the Wall Plate (cont’d) P4263TP Step 2 ➊➊ Place the wall plate against the wall in the desired ➋➋ ➍➍ ➎➎ ➏➏ viewing location. Adjust the wall plate to match the locations of the steel studs. Level the wall plate. Use a pencil and mark 2 upper and 2 lower locations where you will be drilling holes for the steel stud anchors. Set the wall plate to one side in a safe location. Step 3 ➊➊ Use a power drill and ➋➋ 7 /16″ drill bit to drill a hole at each of the marks.
P4263TP Installing the Wall Plate (cont’d) Step 5 ➊➊ Align the wall plate over the steel stud anchor sleeves. ➋➋ Insert a steel stud anchor screw and a / ″ washer into 5 ➌➌ 16 each steel stud anchor sleeve. Use a Phillips screwdriver and tighten each steel stud anchor screw until it is just snug. Do not overtighten the steel stud anchor screws. Do not use a power drill to tighten the steel stud anchor screws. Proceed to the “Installing the Mounting Bracket” section.
P4263TP Installing the Mounting Bracket (cont’d) Universal Washer Installation Premier Mounts’ Universal Washers are designed to accommodate the various M4, M5, M6 and M8 hole sizes required by flat panels. Do not place excessive pressure on the back of the flat panel, as this may damage your flat panel. The Universal Washer must be installed between the head of the mounting screw and the mounting bracket as shown.
P4263TP Installing the Mounting Bracket (cont’d) Locking and Leveling Screw Installation Leveling Screw Installation You must install the leveling screws before you attach the mounting bracket to the back of the flat panel. The leveling screws consists of two (2) M6 x 250mm screws. Thread one (1) leveling screw into the top mounting hole on each of the mounting brackets. Make sure the leveling screw is securely threaded into the mounting tab before proceeding.
P4263TP Lock-It™ Security Barrel Installation (Optional) Optional security configurations include: - PCB-CSL1 (sold separately) - Padlock (Combination or Keyed; commercially available) Mounting Tab Please read the following directions to install the security barrel: the locking screw from the mounting ➊➊ Remove bracket. the locking screw into and through the ➋➋ Place security barrel (see illustration below). the locking screw and security barrel into ➌➌ Re-insert the mounting bracket.
P4263TP Attaching the Mounting Bracket to the Flat Panel This section assumes that you have read and understood these sections: ●● Selecting the Proper Mounting Hardware ●● Universal Washer Installation ●● Universal Spacer Installation ➊➊ Place your flat panel screen-side down on a soft, flat ➋➋ ➌➌ ➍➍ surface. Identify the number and location of the thread inserts on the back of your flat panel. Align the holes on each mounting bracket with the thread inserts on the back of your flat panel.
Mounting Bracket Adjustments P4263TP Leveling Screw Adjustment If your flat panel is tilted too far to one side, the leveling screws will allow you to compensate for this tilt by adjusting the screws with a screwdriver. ➊➊ Loosen both locking screws. ➋➋ Adjust the tilt of your flat panel. ➌➌ Tighten both locking screws. M6 x 30mm Leveling Screw (1 per Bracket) Caution! It is possible to dislodge your flat panel while you level your flat panel. Use extreme caution until you tighten the locking screws.
P4263TP Utilizing the Security Barrel Your P4263TP Mount includes one (1) Security Barrel which can provide additional theft deterrence for your flat panel. PCB-CSL1 Security Cable Thread the cable through the hole on the security barrel. Attach the PCB-CSL1 locking mechansim and secure it using the supplied key. Padlock Place the locking hook through the hole of the security barrel. Snap lock and locking hook together.
P4263TP Warranty PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product. The limited warranty is valid only for the original purchaser of the product. What Premier Mounts Will Do At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is defective.
