INSTALLATION INSTRUCTIONS MVW55 Video Wall Frame EUROPE NORTH AMERICA 1321 S. State College Blvd. Fullerton, CA 92831 USA USA and Canada Phone: 1.800.368.9700 Fax: 1.800.832.4888 Other Locations Phone: (001).714.632.7100 Fax: (001).714.632.
MVW55 Contents Contents........................................................................................................................................................................... 2 Warning Statements......................................................................................................................................................... 2 Installation Tools.........................................................................................................................
MVW55 Installation Tools The following tools may be required depending upon your particular installation. They are not included. Rigging Hardware #2 Phillips Tip Screwdriver Ladder M6 Allen Wrench Tape Measure Level Heavy-Duty Steel Tube Long Enough to Hang MVW55(s) Parts List Make sure your Premier Mounts product has the following hardware and components before beginning installation. If there are parts missing and/or damaged, stop the installation and call Premier Mounts at (800) 368-9700.
MVW55 Features The MVW55 Video Wall Frame is designed for mounting the NEC X551UN to Premier Mounts’ dual-pole carts and stands, or flying them from above. They can be installed in either portrait or landscape orientation. Quick-release buttons make it easier than ever to install the displays, which can be attached to the front and/or back of the MVW55. You can join multiple MVW55s horizontally and/or vertically to create a video wall.
MVW55 Installing the MVW55 Introduction The Premier Mounts MVW55 Video Wall Frame is designed for use with Premier Mounts’ dual-pole carts and stands, as well as for flying from above. You may use one MVW55 as a standalone mount, or multiple MVW55s to create a video wall display. Please read through the safety instructions before installation. Are you mounting the MVW55 to a cart or stand, or flying from above? If dual-pole cart or stand, continue to Cart Or Stand Installation below.
MVW55 Step 2 Full View Top/Bottom View Side View The arrows show where the M8 x 16mm pan Phillips screws can go from inside to fasten MVW55s together. Figure 1 If you are fastening multiple MVW55s, use the M8 x 16mm pan Phillips screws provided to fasten them together from inside the frames (Figure 1). To safely install rows of multiple MVW55s, fasten them first in individual rows, then insert the tubing of the dual-pole cart or stand into each row. After that, fasten the rows together (Figure 2).
MVW55 Step 3 1) Slide the MVW55 to the desired height on the dual-pole cart or stand. 2) Insert four (4) M8 x 10mm set screws into the MVW55 screw holes near the tubing (see drawing). 3) Tighten the screws against the MVW55 and tubing. Tubing of Cart or Stand Back-View Close Up of MVW55 Step 4 When installing the NEC X551UN, attach four (4) universal spacers, four (4) 6mm quick-release buttons and four (4) M6 x 30mm pan Phillips screws to the display’s back mounting holes.
MVW55 Flying Installation Illustrations show only some of the installation configurations possible with the MVW55s. Step 1 Figure 1 If flying the MVW55(s), insert a heavy-duty steel tube (not included) into the frames’ upper 2” circular cutouts (Figure 1). Appropriate tubing and rigging hardware must be used to support a minimum of 4 times the combined weight of all the flat-panel displays and MVW55s used. The steel tube must be long enough to span the entire width of the frame(s) (Figure 2).
MVW55 Step 2 Full View Side View Top/Bottom View The arrows show where the M8 x 16mm pan Phillips screws can go from inside to fasten MVW55s together. Figure 1 If you are fastening multiple MVW55s, use the M8 x 16mm pan Phillips screws provided to fasten them together from inside the frames (Figure 1). To safely install rows of multiple MVW55s, fasten them first in individual rows, then fasten the rows together. After that, insert the heavy-duty plastic tube (Figure 2).
MVW55 Step 3 Front-View Close Up of MVW55 1) Slide the MVW55 to the desired position against the tube. 2) Insert two (2) M8 x 10mm set screws into the corner screw holes above the tube (Figure 1). 3) Tighten the screws against the MVW55 and the tube. 4) Inside the MVW55, wrap and secure rigging/flying hardware (not included) around the tube (Figure 2).
MVW55 Step 6 1) Use the rigging/flying hardware to safely suspend the MVW55(s) overhead. 2) To set the tilt angle, attach additional cables to the bottom of the frames and pull to the desired angle (see drawing). Rigging/Flying Hardware Re-check all hardware and installation for proper tightness and security. Pull additional cables at the bottom of the frames to adjust the tilt. Technical Specifications All measurements are in inches [mm]. 2x 47.88 3.36 16.07 A 400 2x 15.75 A 2x 27.05 5.7 16.
MVW55 Warranty PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product. The limited warranty is valid only for the original purchaser of the product. What Premier Mounts Will Do At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is defective.
