LMVSP Installation Guide Release Pop Out Ultra Slim Portrait Mount www.mounts.com | North America 800.368.9700 | International +1-714-632-7100 1321 S. State College Blvd.
LMVSP Maximum Flat Panel Weight: 100 lb. / 45.35 kg.
LMVSP Installation Guide Wood Stud Installation 1 You must secure the mount to two (2) wall studs with four (4) lag bolts (2 lag bolts for each stud found). X 1) Use a stud finder to determine the wall studs in the vicinity of the mount. 2) Use a pencil to mark each of the wall studs. X 2 Two people are recommended for this step; one person to level the mount and another person to mark the wall stud location. 1) Place the mount against the wall in the desired viewing location.
LMVSP Installation Guide 3 Drill a “pilot hole” on the upper right mark using a M6 or 1/4” drill bit and power drill. X X 4 1) Place the mount against the wall and align it with the pilot hole. 2) Insert one (1) 5/16” x 3˝ lag bolt and one (1) 5/16”washer into the upper right pilot hole. 3) Use a socket wrench and a 13mm or 1/2” socket to tighten the lag bolt. Do not over tighten the lag bolt. Page 4 www.mounts.com | North America 800.368.
LMVSP Installation Guide 5 1) Level the mount using a leveler 2) Use a pencil to mark the remaining three (3) mounting locations of each wall studs. 6 Drill a “pilot hole” on each of the marks with a power drill and a M6 or 1/4″ drill bit. www.mounts.com | North America 800.368.
LMVSP Installation Guide 7 1) Insert one (1) 5/16” x 3″ lag bolt and one (1) 5/16” washer into each pilot hole 2) Tighten all lag bolts using a socket wrench and 13mm or 1/2” socket. Do not over tighten the lag bolts when attaching the mount to the wall. Improper installation may result in personal injury or property damage. 8 Page 6 Concrete wall Installation 1) Place the mount against the wall in the desired viewing location. 2) Use a pencil to mark the upper right mounting location www.
LMVSP Installation Guide 9 10 11 Use a drill and M8 or 5/16” concrete drill bit to drill a pilot hole. 1) Insert a concrete wedge anchor into the hole. Lightly tap the concrete wedge anchor into place with a hammer. 2) Remove the nut and washer from the concrete wedge anchor. 1) Place the LMVSP against the wall over the threaded shaft of the concrete wedge anchor. 2) Replace the washer which you removed from the concrete wedge anchor with the 5/16” washer.
LMVSP Installation Guide 12 1) Level the LMVSP using a leveler 2) Mark up the remaining three (3) mounting locations. 3) Remove the LMVSP 13 Use a drill and M8 or 5/16” concrete drill bit to drill three (3) pilot holes. 14 1) Insert the concrete wedge anchors into each hole. Lightly tap each concrete wedge anchors into place with a hammer. 2) Remove the nuts and washers from the concrete wedge anchors. Page 8 www.mounts.com | North America 800.368.
LMVSP Installation Guide 15 1) Place the LMVSP against the wall over the threaded shafts of the concrete wedge anchors. 2) Replace the washers which you removed from the concrete wedge anchors with the 5/16” washers. 3) Attach the nuts and 5/16” washers to the concrete wedge anchors and tighten using a socket wrench and a M10 socket.
LMVSP Installation Guide This spacer is shown for illustration purposes only. Your spacer may look different depending on the display model you are installing. 1) Once your LMVSP is mounted in the desired location and is level, align your spacer to the top left or right (depending on your install direction) corner register tabs of your mount. You may use commercially available hardware to secure the spacer to the wall during installation (depending on the wall material).
LMVSP Installation Guide Selecting the Mounting Hardware Marking the 1/8” Allowance 1) Insert a small straw or toothpick into the threaded inserts found on the back of the flat-panel. 2) Use a pencil to mark the depth of the threaded insert on the small straw or toothpick. 3) Mark the straw or toothpick 1/8” above the depth of the threaded insert, as shown in Figure 1.
LMVSP Installation Guide Universal Washer Installation Premier Mounts’ Universal Washers are designed to accommodate the various M4, M5, M6 and M8 hole sizes required by flat-panels. Do not place excessive pressure on the back of the flat-panel, as this may damage your flat-panel. M8 M5, M6 M4 The Universal Washer must be installed between the head of the mounting screw and the mounting bracket as shown.
LMVSP Installation Guide Attaching the Mounting Brackets to the Flat-Panel 1) Secure each mounting bracket to your flat-panel by inserting a minimum of two (2) screws per bracket. Do not overtighten the mounting hardware. Make sure the directional arrows on the mounting brackets are facing up. NOTE: For smaller vesa bolt patterns, reverse the mounting brackets. 2) Before tightening the screws, push the bracket up to remove slack from the bracket, then tightened the screw.
LMVSP Installation Guide Post-Installation Adjustments The LMVSP has a set of post-installation adjustments on each mounting bracket (Figure 1). See Note Use the M5 Allen Driver (supplied) to fine-tune adjust. See Note Make sure the the locking safety screws are loosened before making adjustments. Note: Screws have a limited travel adjustment. Do not overtighten or over adjust the screw to avoid damage to threaded holes.
LMVSP Installation Guide Move Inward Left Control Right Control Move Outward Left Control Right Control Tilt Left Left Control Right Control Tilt Right Left Control Right Control www.mounts.com | North America 800.368.
LMVSP Installation Guide Positive / Negative Tilt Negative Tilt control Positive Tilt Control Post Leveling (Up) Left Control Right Control Post Leveling (Down) Left Control Right Control Push evenly on location as shown C L C L Page 16 www.mounts.com | North America 800.368.
LMVSP Installation Guide Use the GAPit GO/No Go Gauge (supplied with model specific spacer) as a final step in the process to inspect and adjust the gap to prevent costly replacement and extend the lifespan of the displays. Damage happens when weight is transferred to the ultra-thin bezels of video wall installations, if the recommended gap specifications of .050” is not maintained vertically and horizontally. This results in image distortion, and costly repairs and replacement. 1.
LMVSP Installation Guide Maintenance 1) Push evenly in the front of the LMVSP to release the single latch spring lock(Figure 1). Single Latch Spring Lock Figure 1 Servicing 1) Slowly pull the front of the LMVSP to extend the scissor arms (Figure 2). 2) Loosen the locking safety screws on both mounting brackets. 3) Tilt up the bottom of the flat-panel, then set their kickstands against the bottom tubing of the mount (Figures 2 & 3).
LMVSP Installation Guide PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Lifetime Warranty Premier Mounts warrants all mounting products to be free from defects in material and workmanship for the lifetime of the original installation of the product. What Premier Mounts Will Do At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is defective.
