INSTALLATION INSTRUCTIONS Single-Stud/Dual-Stud Short-Throw Projector Wall Mount Model: EST100/EST200 NORTH AMERICA 1321 S. State College Blvd Fullerton, CA 92831 USA USA and Canada Phone: 1-800-368-9700 Fax: 1-800-832-4888 Other Locations Phone: (001) 714-632-7100 Fax: (001) 714-632-1044 9530-011-001-0X Rev.
EST100/EST200 Table of Contents Heading 1 Weight Capacity 2 Warning Statements 2 Installation Tools 3 Parts List 3 Features 4 Determining the Installation Height 5 Wood Stud Installation 6 Throw Distance Calculation 10 Projector Installation 10 Attaching the Mount Carriage 11 Multiple Mounting Point Installation 12 Single Mounting Point Installation 14 Attaching the Mount Carriage
EST100/EST200 Installation Tools The following tools may be required depending upon your particular installation. They are not included. Phillips Screwdriver ⅛˝ Drill Bit Drill Level Electronic Stud Finder Parts List Make sure your Premier Mounts product has the following hardware and components before beginning installation. If there are parts missing and/or damaged, stop the installation and call Premier Mounts at (800) 368-9700.
EST100/EST200 Warning Do NOT over-tighten lag bolts when attaching the mount to the wall. Improper installation may result in personal injury or damage to property. THE EXACT CENTER OF THE STUD MUST BE LOCATED FOR CORRECT AND SAFE INSTALLATION. Are you installing the single-stud EST100 or the dual-stud EST200? If EST100, continue to the “EST100 Installation” section below. If EST200, go to the “EST200 Installation” section on page 8.
EST100/EST200 EST200 Installation Step 1 Wood Stud Use an electronic stud finder (not supplied) to locate the center of the stud that is in the wall. Stud finder Step 2 Use a pencil to mark the first mounting point, just above your height mark (from page 5). Mounting Point Mark Height Mark (from page 5) Step 3 Wood Stud Use the level to make sure the back plate is level from side to side.
EST100/EST200 Step 5 Put the projector arm cover plate on the projector arm. Projector Arm Cover Plate Projector Arm Step 6 Place the projector arm assembly within the desired mounting slots on the nn back plate. Use four (4) M5 x 10mm security screws, four (4) M5 flat washers and four oo (4) sleeve bushing nylons to attach the projector arm assembly to the back plate. The elongated mounting slots in the back plate allow some lateral shift for precisely adjusting the projector arm.
EST100/EST200 Attaching the Mount Carriage Selecting the Mounting Hardware Insert a small straw or toothpick into the threaded inserts nn found on the bottom or top of the projector. Use a pencil to mark the depth of the threaded insert on the oo small straw or toothpick. Mark the straw or toothpick 1/8” above the depth of the pp threaded insert, as shown in Figure 1.
EST100/EST200 Multiple Mounting Point Installation Step 1 Locate the projector’s mounting points. nn Position the mounting legs on the projector. oo The mounting legs are pre-installed. Depending on the requirements of your projector, you may remove one of the mounting legs. The number and placement of mounting points on projectors varies between projector manufacturers. Refer to you projector’s technical specifications for the number and location of the mounting points on your specific projector.
EST100/EST200 Mounting Hardware Too Long? The depth of some projector mount points may prevent you from tightening the M2.5 and M3 mounting hardware. You can reduce the length of the M2.5 and M3 mounting hardware by stacking up to a maximum of five (5) M3 flat washers inside the leveling barrel. Avoid stacking too many M3 washers; the mounting hardware must thread into the projector mount point at least four (4) complete turns. Step 4 Identify the projector’s approximate front-to-back center of gravity.
EST100/EST200 Step 6 Tighten the mounting screws which secures the mounting legs to the nn projector. Do not overtighten the mounting screws. Step 7 Insert one (1) Barrel Cap (except for the security barrel) into the end of each nn leveling barrel. Go to the “Attaching the Mount Carriage to the Projector Arm” section on page 15. Single Mounting Point Installation A single ¼-20 x 5/16″ screw must be used to attach the mount carriage to the projector if your projector has only one mounting point.
EST100/EST200 Attaching the Mount Carriage to the Projector Arm Step 1 Insert and slide the mount carriage along the projector arm to the desired position. Projector not shown Step 2 Once you have the desired position, use one (1) M5 x 10mm security screw to tighten the mount carriage in place. M5 x 10mm Security Screw Proceed to the “Cable Routing (Optional)” section on page 16. Installation Instructions Visit the Premier Mounts website at http://www.mounts.
EST100/EST200 Cable Routing (Optional) Remove the plastic cover(s) from the cable routing openings. nn Route cables and wiring through the openings then out the back or bottom near the oo wall. Proceed to the “Securing the Projector (Optional)” section. Plastic Cover Route cables and wiring through the projector arm openings then out the back or bottom near the wall. Securing the Projector (Optional) PCB-CSL1 Page 14 Padlock (Combination or Keyed) Visit the Premier Mounts website at http://www.
EST100/EST200 Mount Adjustment After the projector has been installed, the projector must then be adjusted. To adjust the projector: Loosen the M5 set screw using the M5 Allen wrench (both sides). nn Adjust the projector to the correct position. Firmly grasp the projector in both oo hands, and tilt either forward or backward to adjust the level. -ORFirmly grasp the projector in both hands and rotate side to side for pp orientation adjustment. Tighten both M5 set screws using the M5 Allen wrench.
EST100/EST200 PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Lifetime Warranty Premier Mounts warrants all mounting products to be free from defects in material and workmanship for the lifetime of the original installation of the product. What Premier Mounts Will Do At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is defective.