INSTALLATION MANUAL CTM-4200 NORTH AMERICA EUROPE AUSTRALIA, NEW ZEALAND, OCEANIA (DISTRIBUTOR) 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada – Phone: 800-368-9700 Fax: 800-832-4888 Swallow House, Shilton Industrial Estate, Shilton, Coventry, England CV79JY Phone: +44 (0) 2476 614700 Fax: +44 (0) 2476 614710 P.O. Box 295 Mordialloc Victoria 3195 Australia Phone: 03 9586 6330 www.premiermounts.com.au Other Locations – Phone: 001.714.632.7100; Fax: 001.714.632.
CTM-4200 Table of Contents Warning Statements ........................................................................................................................................- 3 Parts List........................................................................................................................................................... - 4 Installation Tools ........................................................................................................................................
CTM-4200 Warning Statements WARNING: PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS PRODUCT FOR PUROPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS, AND IS NOT RESPONSIBLE FOR ANY DAMAGES, CLAIMS, DEMANDS, SUITS, ACTIONS, OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM, ARISING OUT OF OR IN ANY MANNER RELATING TO ANY SUCH USE, ATTACHMENTS OR MODIFICATIONS.
CTM-4200 Parts List NOTE: This mount is shipped with all proper installation hardware and components. Make sure that none of these parts are missing and/or damaged before beginning installation. If there are parts missing and/or damaged, please stop the installation and contact Premier Mounts (800-368-9700).
CTM-4200 M4 x 16 (Qty 8) M5 x 16 M5 x 20 (Qty 6) M8 x 20 (Qty 6) (Qty 6) M4 x 25 M5 x 12 M6 x 20 (Qty 8) (Qty 8) M8 x 25 (Qty 6) M8 x 30 M8 x 35 M5 x 50 Page - 5 - (Qty 6) (Qty 6) M5 x 25 M6 x 12 (Qty 6) (Qty 6) (Qty 4) (Qty 2) M8 x 70 (Qty 4) Installation Manual
CTM-4200 PCM-4200 / CTM-4200 Nylon spacers and flat washers’ actual size NOTE: The nylon spacers may be stacked to achieve proper spacing.
CTM-4200 Thread Depth Indicator 1. 2. 3. 4. Insert the thread depth indicator (supplied) through the thread inserts found on the back of the flat panel to make sure the inserts measure the same full depth and mark it (Figure 1). Locate the correct diameter screw for the thread insert. Compare your marking to the screws (supplied). If your selected screw is longer than the marking on the thread depth indicator, DO NOT USE this screw. The screw length must not bypass the marking.
CTM-4200 Mounting Bracket Installation NOTE: Proper installation procedure by qualified personnel as outlined in the installation instructions must be adhered to. Failure to do so could result in serious personal injury and possible damage to the flat panel. WARNING: INVERT THE FLAT PANEL PLACE IT ON A SOFT, FLAT SUFRACE TO PREVENT DAMAGE TO THE FLAT PANEL. USE A BLANKET, FOAM, ETC. FAILURE TO DO SO WILL RESULT IN DAMAGING THE FLAT PANEL.
CTM-4200 3. 4. Install nylon spacers (if needed) to the mounting points on the flat panel (Figure 6). Lay the left and right mounting brackets (stamped arrows facing out) - (Figure 7). Mounting Brackets Nylon Spacers, If Applicable Bottom of Flat Panel Arrows Facing Out Center Mark Inverted Flat Panel Figure 6 5. 6. Figure 7 Match the center of viewing guide with the centerline you marked in Step 1 (Figure 8).
CTM-4200 7. 8. The Griplate™ have M4, M5 M6 and M8 hole patterns to fit the hardware that your flat panel requires. EXAMPLE: If your plasma uses M8 x 20 Phillip screws. Use the M8 mounting points (Figure 10). Once the mounting brackets are aligned secure the Griplate™ to the flat panel. Use (1) Griplate™ per mounting point (Figure 11). NOTE: The dimples of the top plates have to be facing up and the bottom dimples must be facing down.
CTM-4200 CTM-4200 Installation 1. Using a (commercially available) wood stud finder, locate the 16" or 24" stud centers behind the wall. 2. Once found, make a pencil marking on the center of the wood studs. NOTE: The wall plates have 16" and 24" mounting slot positions. 3. Place the wall plate to the reference line and mark the nine (9) lag bolt mounting points through the wall plate slots on the wall. 4. Level the wall plate with the reference arrow pointing up to the ceiling. 5.
CTM-4200 Drill Gun Pilot Holes Figure 14 Installation Manual Figure 15 Page - 12 -
CTM-4200 Installing the Flat Panel Display WARNING: 1. AT LEAST (2) QUALIFIED PERSONNEL ARE STRONGLY RECOMMENDED FOR INSTALLATION OF THIS PRODUCT. FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY AND POSSIBLE DAMAGE TO THE FLAT PANEL. Raise the flat panel with the mounting brackets secured to the flat panel and insert the top hooks from each bracket to the rod from the wall plates (Figure 16).
CTM-4200 2. Make any lateral shift adjustment and lock it by tightening the two (2) M6 x 12mm Phillips screws found on the bottom of the mounting brackets. CAUTION: Do not over tighten the M6 x 12mm Phillips screws to the rods (Figure 17). NOTE: To remove the display from the wall, simply back off the M6 x 12mm Phillips screws using a Phillips screwdriver and lift the unit of the wall carefully.
CTM-4200 3. Tilt the flat panel and secure the two (2) M6 x 12mm safety knobs to each of the mounting brackets. NOTE: To remove the display from the wall simply extend the display to its maximum tilt range, remove the two knurl knobs push the flat panel back to it’s flat position, loosen or remove the two (2) M6 x 12 lateral shift screws and lift the unit of the wall (Figure 18).
CTM-4200 Technical Specifications All measurements are in inches(mm) 11.375 (288.9) 3.250 (82.5) 4.500 (114.3) 3.250 (82.5) 11.375 (288.9) 7.401 8.000 (187) (203.2) 21.000 (533.4) 5.000 (127) 4.500 5.000 (114.3) (127) 8.000 (203.2) 6.599 (167.6) 6.750 (171.4) 10.000 (254) 24.000 (609.6) 32.000 (812.8) 36.000 (914.4) 12° 6.424 (163) C 2.448 (62.9) TRA R ILLUS N EL FO LAT PA OSE ONLY PURP TION NOTE: FLAT PANEL FOR ILLUSTRATION PURPOSE ONLY F NOTE: 19.000 (482.
CTM-4200 Warranty Limited Lifetime Warranty All Premier Mounts products carry a limited lifetime warranty from ship date against defects in materials and workmanship. Premier Mounts is not liable for improper installation that results in damage to mounts, adapters, display equipment or personal injury. DISCLAIMER OF WARRANTY.
