INSTALLATION INSTRUCTIONS AM3/AM3-B Universal Swingout Arm NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada – Phone: 800-368-9700 Fax: 800-832-4888 EUROPE Swallow House, Shilton Industrial Estate, Shilton, Coventry, England CV79JY Phone: +44 (0) 2476 614700 Fax: +44 (0) 2476 614710 Other Locations – Phone: (001)-714-632-7100; Fax: (001)-714-632-1044 ©Premier Mounts 2008 9531-007-001-06 AUSTRALIA, NEW ZEALAND, OCEANIA (DISTRIBUTOR) P.O.
AM3/AM3-B Table of Contents Warning Statements Parts List Installation Tools Thread Depth Indicator Mount Orientation Mount Installation Concrete Installation Nose Piece Orientation Universal Mounting Bracket Assembly Attaching the Display Securing the Display Tilt Positioning Cable Access Holes Technical Specifications Warranty Warning Statements 2 3 3 6 7 8 8 9 10 11 12 13 13 14 15 PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS SHOULD BE READ AND COMPLETELY UNDERSTOOD.
AM3/AM3-B Parts List This wall mount is shipped with all proper installation hardware and components. Make sure that none of these parts are missing and/or damaged before beginning installation. If there are parts missing and/or damaged, please stop the installation and contact Premier Mounts (800-368-9700).
AM3/AM3-B M4 x 16 (Qty 8) M6 x 30 (Qty 8) (Qty 8) M4 x 25 (Qty 8) M6 x 45 M5 x 12 M5 x 16 M5 x 20 (Qty 8) M8 x 20 (Qty 8) (Qty 8) M8 x 25 (Qty 8) (Qty 8) (Qty 8) M5 x 25 M8 x 30 (Qty 8) M5 x 50 (Qty 8) M6 x 16 M6 x 20 (Qty 8) (Qty 8) M8 x 35 M8 x 45 M8 x 70 Page 4 (Qty 8) (Qty 8) (Qty 4) Installation Instructions
AM3/AM3-B The nylon spacers may be stacked to achieve proper spacing.
AM3/AM3-B Thread Depth Indicator 1. Insert the thread depth indicator (supplied) through the thread inserts found on the back of the flat panel to make sure the inserts measure the same full depth and mark it (Figure 1). 2. Locate the correct diameter screw for the thread insert. Compare your marking to the screws (supplied). 3. If your selected screw is longer than the marking on the thread depth indicator, DO NOT USE this screw. 4. The screw length must not bypass the marking.
AM3/AM3-B Mount Orientation The AM3/AM3-B Plasma Mount has the built-in capability of mounting with the swingout arm on either the left or right-hand side. WHEN MOUNTING THE AM3, THE SIDE THAT THE SWINGOUT ARM IS LOCATED ON MUST HAVE A LAG BOLT MOUNTED ON AT LEAST ONE SIDE (SEE FIGURE 1), TOP AND BOTTOM. Step 1. To change the mount orientation, choose the desired side that the mount will open to, left or right. Step 2. Once the side has been determined, attach the mount to the wall.
AM3/AM3-B Mount Installation Before proceeding with the mount installation, you should already have the mounting holes pre-drilled. Please use the template (supplied) and follow the instructions. For ease of installation, it is recommended that two people perform the installation. WHEN MOUNTING THE AM3, THE SIDE THAT THE SWINGOUT ARM IS LOCATED ON MUST HAVE A LAG BOLT MOUNTED ON AT LEAST ONE SIDE ( FIGURE 4, PAGE 8), TOP AND BOTTOM. DO NOT OVERTIGNTEN THE LAG BOLTS WHEN ATTACHING THE MOUNT TO THE WALL.
AM3/AM3-B Nose Piece Orientation Rotate Nose 180° Right Side Orientation Left Side Orientation Figure 7 Tension Bolts Tension Bolts Back Side of Nose Piece Front Side of Nose Piece Figure 8 Step 1. Once the mount has been oriented and mounted to the wall, remove the nose piece by removing the tensions bolts. After loosening the tension bolts, be sure that the nose piece is held together tightly before rotating. Step 2.
AM3/AM3-B Universal Mounting Bracket Assembly Step 1. Place the universal bracket bar and the universal brackets on a flat surface. Step 2. Slide the universal brackets onto the universal bracket bar (as shown in Figure 9) with the set screws facing up. At this time, do not tighten the set screws that are located on the universal bracket. Step 3. Place the display on a soft, flat surface, face-down.
AM3/AM3-B Attaching the Display ONCE THE UNIVERSAL BRACKET BAR ASSEMBLY HAS BEEN ATTACHED TO THE DISPLAY, IT IS RECOMMENDED THAT TWO PEOPLE MOUNT THE DISPLAY, AS THE UNIT IS HEAVY AND, IF DROPPED, WILL DAMAGE THE MOUNT, THE DISPLAY, AND/OR PERSONNEL. Universal Bracket Swingout Arm Nose Piece Universal Bracket Bar Display Figure 10 Figure 11 Step 1. Slide the display assembly onto the nose piece of the swingout arm. Figure 12 Step 2. This is how the units will look when properly fitted together.
AM3/AM3-B Securing the Display Once the two units have been secured together, the two (2) M6 x 30mm Phillips Head locking screws must be installed in the noted location (Figure 14) to prevent any movement.
AM3/AM3-B Tilt Positioning To adjust the display, loosen the tension bolts no more than ½ turn, make the adjustments and then tighten the tension bolts. When tilt positioning is needed to adjust the display, place a hand at the top corner of the display and the other hand at the bottom of the display (Figure 15). To Tilt the Display Gently push both hands inward. This motion will cause the display to tilt forward. To Tilt the Display Back Gently push both hands outward.
AM3/AM3-B Technical Specification All measurements are in inches(mm).
AM3/AM3-B Warranty PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product. The limited warranty is valid only for the original purchaser of the product. What Premier Mounts Will Do At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is defective.
