CREATING POSITIVE CUSTOMER EXPERIENCES INSTALLATION INSTRUCTIONS Extending Swivel Mount for Flat-Panels Model: AM225 NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada Phone: 1-800-368-9700 Fax: 1-800-832-4888 Other Locations Phone: (001)-714-632-7100 Fax: (001)-714-632-1044 EUROPE Unit 3, The Moorings Business Park, Channel Way, Longford, Coventry, CV6 6RH, UK Phone: +44 (0) 24 7664 4105 Fax: +44 (0) 24 7664 4165 9531-021-001-02
AM225 Contents Weight Limit............................................................................................................................................................... 2 Warning Statements.................................................................................................................................................. 2 Installation Tools.........................................................................................................................................
AM225 Installation Tools The following tools may be required, dependent upon your particular installation. These tools are not provided by Premier Mounts, but you can purchase them at your local hardware store. ¼˝ Drill Bit for Wood Stud Electronic Stud Finder /16˝ Concrete Drill Bit** Hand Held Drill Hammer** Level 5 2 1 Pencil Tape Measure Zip Ties Socket Wrench M10 Socket* ½˝ Socket Phillips Tip Screwdriver ** Optional tools for concrete installations.
AM225 Features The Extending Swivel Mount (AM225) is the ideal wall mount for flat-panels. It extends smoothly up to 20 inches from the wall, and allows simple post-installation leveling and swivel adjustments for the perfect viewing angle. Its open design makes it easy to set up cable and electrical wiring. The AM225 works with the P-Series P4263F or P4263T flatpanel mount to help support the display. Stylish Design Sleek, sturdy and unobtrusive.
AM225 Building the Wall Frame Use eight (8) M4 x 8mm combo Phillips screws to attach the two (2) crosspiece brackets to the two (2) wall mounting brackets (Fig. 1). Make sure the brackets are facing in the same direction as shown (Fig. 1). The screws must been inserted as shown (Fig. 2 and Fig. 3) M4 x 8mm combo Phillips screw M4 x 8mm combo Phillips screw Fig. 1 Fig. 2 Top of Wall Frame Fig. 3 Bottom of Wall Frame Proceed to the “Installing the Wall Frame” section.
AM225 Installing the Wall Frame Introduction Facing the Front Make sure the flat side of the wall frame’s crosspiece brackets is facing the front. Mounting Safety Two people are recommended for installing this mount. Front-facing wall frame Determining the Mounting Surface If you will be installing your AM225 mount to wood studs, proceed to the “Wood Stud Installation” section. If you will be installing your AM225 mount to a concrete wall, proceed to the “Concrete Installation” section.
AM225 Installing the Wall Frame (cont’d) Step 3 Drill a “pilot hole” in the center of the upper right mark using a ¼˝ drill bit and power drill. Only use a ¼˝ drill bit when drilling the pilot holes. Step 4 Place the wall frame against the wall and align it with the pilot hole. Insert one (1) 5/16˝ x 3˝ lag bolt and one (1) 5/16˝ washer into the upper right mounting hole and tighten using a socket wrench and ½˝ socket. Do not overtighten the lag bolt. Step 5 Level the wall frame.
AM225 Installing the Wall Frame (cont’d) Step 7 Insert one (1) 5/16˝ x 3˝ lag bolt and one (1) 5/16˝ washer into each pilot hole. The wide mounting slots in the wall frame allow lateral shift to help you precisely position the pullout mount. Tighten all lag bolts using a socket wrench and ½˝ socket. Do not overtighten the lag bolts when attaching the mount to the wall. Improper installation may result in personal injury or property damage. Proceed to the “Installing the Mounting Bracket” section.
AM225 Installing the Wall Frame (cont’d) Step 3 Insert a concrete wedge anchor into each hole. If necessary, lightly tap each concrete wedge anchor into place with a hammer. Remove the nuts and washers from all four (4) concrete wedge anchors. Step 4 Place the wall frame against the wall over the threaded shafts of the concrete wedge anchors. Replace the washers which you removed from the concrete wedge anchors with the 5/16˝ washers shown in the parts list on Page 3.
AM225 Installing the Pullout Mount ➊➊ Pre-install two (2) M8 x 12mm combo Phillips M8 x 12mm combo Phillips screw screws in the top screw holes of the wall frame (Fig.1) using at least 5 full turns. Leave a gap between the heads of the screws and the wall frame for hanging the pullout mount. ➋➋ Hang the pullout mount on the M8 x 12mm combo screws that were pre-installed in the wall frame (Fig. 2). The keyhole design of the pullout mount’s screw holes makes hanging easier. ➌➌ Wall Frame Fig.
AM225 Attach a P-Series Mount and/or Accessories Use four (4) M8 x 16mm pan Phillips screws to attach the P-Series P4263F or P4263T flat-panel mount to the AM225. Follow the installation instructions included with the P-Series mount. Make sure the P-Series mount is aligned to the center of the pullout portion of the AM225. Proceed to the “Post-Installation Adjustments” section.
AM225 Cable Routing Neatly organize cabling and wiring by: • Routing them through the openings in the pullout Cable Routing Openings mount. • Using zip ties (not included) through the zip-tie holders on the side brackets. Zip-tie Holders Technical Specifications All measurements are in inches [mm]. 421 16.6 247.65 9.75 477.67 18.806 92 3.60 156.46 6.16 0 198.63 7.820 420.4 16.5 114.3 0 4. 5 Page 12 Visit the Premier Mounts website at http://www.premiermounts.
AM225 Warranty PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product. The limited warranty is valid only for the original purchaser of the product. What Premier Mounts Will Do At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is defective.
