Heavy Duty Mixer Grinder Instruction Manual & Gurantee Card
Technical Specifications Model & No. : Eco Plus - MG 138 Voltage : 110V AC 60 Hz Power Consumption : 550 Watts Insulation : Class F Protection : Class I Rating : 30 Minutes Motor : Universal 550 Watts High Power Motor. No load speed 18,000 RPM (approx.) With load speed 10,500 RPM (approx.) Material of Body : A.B.S. Material of Jars : Stainless Steel Maya Appliances (P) Ltd.
1.00 LITRE JAR DOME LID DOME LID POLYCARBONATE DOME POLYCARBONATE DOME DOME GASKET DOME GASKET JAR HANDLE Jar Handle Removable Blade 1.50 LITRE JAR CHUTNEY JAR FIXED MULTIPURPOSE BLADE Polycarbonate Lid C.G GASKET JAR COUPLER MOTOR COUPLER GROOVE Jar Handle TOP CAP Fixed Multipurpose Blade MIXIE BODY NOTE: JAR SEATING: Seat Jar on Top Cap, ensuring that the Locks fit properly in the Grooves of the Top Cap. SPEED CONTROL: Turn Rotary Switch clockwise for Speed 1,2 or 3, as desired.
HOW TO USE YOUR PREETHI is provided with a 10 Amps 3-pin Plug and a 2 metre Cord. Plug the Power Cord to a 110 Volts AC supply only. FUNCTION & PURPOSE DRY GRINDING: Roasted cereals, dry masala, dal, roasted coffee seeds, coriander seeds, red chillies, pepper, raw rice, etc. IMPORTANT INSTRUCTIONS 1. Ensure that the ingredients, Jar, Dome and Blade are thoroughly dried before use. 2. While Dry Grinding, friction may heat up the Jar. It has nothing to do with the Motor. So do not worry. 3.
GRINDING INSTRUCTIONS IDLI, DOSA, UTTAPPAM, APPAM, PESRATTU & VADA: Use Dry & Wet Grinding Jar 1. Soak Rice / Dal for 4 to 5 hours as required. COCONUT CHUTNEY, TOMATO & ONION CHUTNEY, CORIANDER & MINT CHUTNEY, ETC: Use Chutney Jar 2. Drain water from ingredients. 3. Minimum - Upto Blade level at least. Maximum - 0.40 litre (1.50 litre Jar) 0.30 litre (1.00 litre Jar) DO NOT EXCEED ABOVE QUANTITIES AS THE MOTOR WILL GET OVER LOADED OR THE BATTER WILL GET HEATED UP. 3.
DOs DON’Ts 1. Place PREETHI at a convenient height for easy operation. 1. Do not operate unless Jar and Dome are in proper position. 2. Ensure that PREETHI is placed on an even, smooth, hard and clean surface. (otherwise dust will be sucked up through the Bottom Plate and the unit will be unstable.) 2. Do not remove Jar assembly before the Blade comes to a complete stop, after switching off the Motor. 3. Make sure the Stainless Steel Jars are clean and dry. 3.
AUTO OVERLOAD PROTECTOR If your Mixie stops in usage, due to operation of the Overload protector, then: 1. FIRST SWITCH OFF THE MIXIE. 2. Remove some material which is being ground from the Jar, to decrease the load. 3. Wait for 3 minutes. 4. Lift the Unit and press the RED KNOB projecting out of Bottom Plate. 5. Re-start the Mixie. CLEANING BODY AND TOP CAP 1. Clean Body and Top Cap with a damp cloth and wipe dry. 2. Do not use abrasives or water for cleaning. STAINLESS STEEL JARS 1.
MAYA APPLIANCES (P) LTD. 3/140, I.T. Highway, Oggiam Thoraippakkam, Chennai 600 097. INDIA. Tel: 91 44 2496 4477. Fax: 91 44 2496 0349. email: info@preethi.biz. Website: www.preethi.
