Operating and Maintaining the P30 Console Precor Incorporated 20031 142nd Avenue NE P.O.
Edition Information OPERATING AND MAINTAINING THE P30 CONSOLE P/N 301096-201 rev C Copyright © June 2011 Precor Incorporated. All rights reserved. Specifications subject to change without notice. Trademark Note Precor, AMT, and EFX are registered trademarks and Preva is a trademark of Precor Incorporated. Other names in this document may be the trademarks or registered trademarks of their respective owners.
Important Safety Instructions This apparatus (hereinafter referred to as the console) is intended to be shipped with new Precor exercise equipment (hereinafter referred to as the base unit). It is not packaged for individual sale. WARNING To prevent injury, the console must be attached securely to the base unit following all assembly and installation instructions shipped with the base unit. The console is intended to be connected to AC mains power through the furnished power supply ONLY.
4 Operating and Maintaining the P30 Console Il est conseillé de subir un examen médical complet avant d’entreprendre tout programme d’exercise. Si vous avez des étourdissements ou des faiblesses, arrêtez les exercices immédiatement. Do not allow children, or people unfamiliar with the operation of this equipment, on or near it. Do not leave children unsupervised around the equipment.
Important Safety Instructions 5 Proper Location for Equipment For all equipment other than treadmills: Locate at least 40 inches (1 meter) away from walls or furniture on either side of the equipment, and 40 inches (1 meter) away from objects behind the equipment. For treadmills: Locate at least 40 inches (1 meter) away from walls or furniture on either side of the treadmill, and at least 80 inches (2 meters) away from objects behind the treadmill.
6 Operating and Maintaining the P30 Console Do not operate the equipment where aerosol (spray) products are being used or where oxygen is being administered. Do not use outdoors. Do not attempt to service the equipment yourself, except to follow the maintenance instructions in this manual. Never drop or insert objects into any opening. Keep hands away from moving parts. Do not set anything on the stationary handrails, handlebars, control console, or covers.
Important Safety Instructions 7 In accordance with the European WEEE Directive, electrical and electronic equipment (EEE) is to be collected separately and to be reused, recycled, or recovered at end of life. Users of EEE with the WEEE label per Annex IV of the WEEE Directive must not dispose of end of life EEE as unsorted municipal waste, but use the collection framework available to customers for the return, recycling, and recovery of WEEE.
8 Operating and Maintaining the P30 Console Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING Per FCC rules, changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
Important Safety Instructions 9 Electrical Recommendations: 120 V and 240 V Treadmills Note: This is a recommendation only. NEC (National Electric Code) guidelines or local region electric codes must be followed. You should have received a power cable that meets your local electrical code requirements along with the equipment. Precor treadmills must be connected to a 20 amp individual branch circuit that can be shared only with one PVS.
10 Operating and Maintaining the P30 Console Electrical Recommendations: All Equipment Excluding Treadmills Note: This is a recommendation only. NEC (National Electric Code) guidelines or local region electric codes must be followed. For equipment fitted with a P80 console or Personal Viewing System (PVS) screen a separate power connection is required. For a 20 amp branch circuit up to 10 screens can be connected.
Table of Contents Important Safety Instructions ................................................... 3 Safety Precautions .................................................................................3 Hazardous Materials and Proper Disposal .................................... 6 Product Recycling and Disposal ....................................................... 6 Regulatory Notices for Cardiovascular Exercise Equipment ......................................................................
Chapter 1 Getting Started The P30 console offers administrators the ability to set default values that meet their specific needs. These settings include items like language, units of measure, and setting a maximum allowed workout time for each piece of equipment. Activating the Console for Self-Powered Equipment Precor equipment is either self-powered or externally powered using an optional power adapter. Self-powered equipment requires the user exercise to initialize the console.
14 Operating and Maintaining the P30 Console Optional Use of the Power Adapter An optional AC power adapter provides sustained power to the equipment. This adapter allows you to change settings without having to pedal the equipment. To purchase the power adapter, contact your dealer. If you purchase the optional power adapter, you must also purchase the internal cable kit. The kit supplies the cable, bracket, and fasteners that connect the power adapter to the lower electronics board.
15 Getting Started Identifying Parts of the Console The following diagram provides information about the console keys. The number and actions of the console keys may differ slightly depending on the type of equipment. Figure 4: P30 console keys Table 1.
16 Operating and Maintaining the P30 Console Number Part Name • Muscle Monitor EFX • Stride Length - AMT • Rate per Minute Climber • - Bike, Treadmill Details • The Muscle Monitor displays the muscles used to perform that workout. • Stride Length describes the length of your steps during a workout. • Rate per Minute displays the number of meters, feet, or steps that a user has gained during a workout.
17 Getting Started Number Part Name Options - All equipment except AMT Details • Press to enter Goals, Language, Weight, Age, and Target Heart Rate information, More Options • Press More Metrics to view additional metric information for all equipment except the AMT Metrics: • Percent Complete • Time in Zone • Segment Time Remaining • Average Speed • Pace - Treadmill only • Calories per Minute • Calories per Hour • WATTS • METS • Target HR • Average HR • Elevations - Treadmill a
18 Operating and Maintaining the P30 Console Number Part Name Number pad Details Use to enter numerical information such as age, weight, and passwords. Press Clear to delete the numbers entered. Press Enter after you have entered numbers on this number pad.
Chapter 2 Setting Up the Console Use the System mode to configure settings in ways that benefit your users and your facility. The System menu is visible only to administrators and registered service technicians. Changes made to these settings are saved to the fitness equipment. The System Settings categories are: Club Settings Informational Display System Settings System Setting features remain hidden from club patrons and can only be accessed using special keypresses.
20 Operating and Maintaining the P30 Console When the equipment is in the Welcome state: PRECOR scrolls on the lower text display. SELECT A WORKOUT OR PRESS QUICKSTART TO BEGIN scrolls in the upper text display. The heart rate signal is the only segment activated. On the treadmill, the belt is not moving and the lift motor is off. Note: On self-powered equipment, the console initializes when you begin working out. You must maintain a minimum rate of motion for the Welcome banner to appear.
Setting Up the Console 21 Setting Club Parameter Values Use this information to customize the equipment for your setting. Safety Code (Treadmill only) Value Range: Enabled or Disabled (Default: Disabled) When the equipment is shipped from the factory, the safety code protection feature is disabled. If you enable the safety code, your users will need to enter a four digit number to begin their exercise session and start the running belt. The code is 1 2 3 4.
22 Operating and Maintaining the P30 Console Set Max Workout Time (All Equipment) Value Range: 1 to 240 minutes (Default: 60 minutes) You can set a maximum workout time per session. Choose a time limit between 1 and 240 minutes, or select No Limit if you do not want to set a time limit. For example, if you set the time limit to 20 minutes, users can only enter a workout time between 1 and 20 minutes. Select No Limit if you do not want to set a time limit.
23 Setting Up the Console Creating a Custom Workout Value Range: ON or OFF (Default Value: OFF) Create a customized program for your workout. Note: This option is not available on all equipment. To create a custom program: 1. At the SET CUSTOM PROGRAM prompt, press OK. The program profile appears in the display and a blinking column indicates your starting point. 2. Press the down arrow key on the navigational keypad, to select the column you want to change. 3.
24 Operating and Maintaining the P30 Console 6. When you have finished creating your program, press OK to save the program profile, and return to the Welcome banner. Press BACK, to exit this setting without saving your changes to the custom profile. Set Speed Limit (Treadmill only) Value Range: Full speed range of equipment (Default: Maximum speed) This setting limits how fast the running belt moves and, consequently, the number of speed settings that are available to the user.
25 Setting Up the Console Set Resistance Range (Bike only) Value Range: High, Medium, or Low (Default: High) You can set a low, medium, or high base resistance on the recumbent or upright bikes. There are 25 levels of resistance within each base setting, but the base setting affects the overall resistance range. The following ranges are available: High: Provides full resistance range. Medium: Provides approximately two thirds of the resistance that is available within the high group setting.
26 Operating and Maintaining the P30 Console Table 4. Informational Displays values Product Value Information provided All The odometer value correlates to the type of equipment and the standard of units, U.S. or Metric, selected in the programs. All ODOMETER HOUR METER • Treadmill: Displays the number of cumulative miles or kilometers logged to date. • EFX or AMT: Displays the number of total strides logged to date. • Bike: Displays the number of total revolutions logged to date.
27 Setting Up the Console Product Value Information provided All Displays any event codes that may have been detected by the software. For more information, refer to Event Log. EVENT LOG Event Log The event log holds a maximum of 30 events. After the log reaches 30 events, older events are erased to make room for newer ones.
28 Operating and Maintaining the P30 Console Event Number Description of Event 23 Motor pulses missing after start up 24 Reduce speed requested, speed is not reducing 26 Motor pulse width incorrect 27 Too much drive motor current 28 Temperature too high 29 Excessive AC input current 30 Communications event lower board to upper board 31 Incorrect Communications event upper board to lower board 32 Communication event upper board to lower board 33 Incorrect communications event lower boa
29 Setting Up the Console User ID Entry with CSAFE Equipment This equipment is fully compatible with CSAFE protocols. When the equipment is connected to a CSAFE master device, the user is prompted to press ENTER and begin an identification process. The user ID is displayed as five zeros and indicates the starting point. The following table describes key functions while in CSAFE mode. Table 6. CSAFE access keys Keys Function Number Keypad Use the number keys to enter a user ID.
30 Operating and Maintaining the P30 Console
Chapter 3 Introducing Users to the P30 Console CAUTION: Before beginning any fitness program, see your physician for a thorough physical examination. Seek advice from your physician to learn the target heart rate appropriate for your fitness level. The P30 console offers an easy-to-follow display and multiple programs to help people meet their exercise needs.
32 Operating and Maintaining the P30 Console To use the touch heart rate feature, place the palm of your hands directly on the metal heart rate sensors on the equipment’s handlebars. To ensure a more accurate heart rate readout, make sure you follow these tips: Both hands must grip the sensors for your heart rate to register. It takes a number of consecutive heart beats (15-20 seconds) for your heart rate to register. When gripping the sensors, do not grip tightly. Keep a loose, cupping hold.
Introducing Users to the P30 Console 33 Using a Chest Strap Transmitter WARNING Signals used by the Chest Strap Transmitter (or heart rate strap) may interfere with pacemakers or other implanted devices. Consult your physician and the manufacturers of your Chest Strap Transmitter and implanted device before using a Chest Strap Transmitter. Wearing a chest strap transmitter during your workout provides steady heart rate information.
34 Operating and Maintaining the P30 Console Using the Treadmill Safety Clip The treadmill is equipped with two different stop functions, which behave as follows: If the user … Then the treadmill belt … And the console … Presses down on the red Slows to a stop STOP button Shows that the exercise workout is paused Pulls on the lanyard Slows to a stop attached to the safety clip and trips the restart switch Shows the words PUSH TO RESET SWITCH and an arrow pointing to the Restart switch The restart s
Introducing Users to the P30 Console 35 If the restart switch trips during exercise, perform the following steps: 1. Reattach the safety clip if necessary. 2. Press the restart switch down until it clicks, returning it to its normal position. Note: If the restart switch trips, all information about the current workout is deleted. 3. Start the workout from the beginning, reducing the time as needed to account for the amount of exercise that has been completed.
36 Operating and Maintaining the P30 Console Treadmill Auto Stop™ (Automatic Stop) Function Important: The default setting for this feature is ON. An administrator can turn off this feature in the System Settings; however, Precor recommends it remain ON. The Auto Stop™ (Automatic Stop) feature is designed to bring the treadmill to a gradual stop when it is not in use. This might occur if a user steps off the treadmill before the end of a workout and leaves the treadmill running.
Chapter 4 Starting a Workout CAUTION: If you are using a treadmill, be sure to attach the security clip to your clothing before starting your workout. The equipment is in the Welcome state when the words SELECT A WORKOUT OR PRESS QUICKSTART TO BEGIN scroll across the scrolling upper text display and PRECOR scrolls on the lower text display. If the equipment is connected to CSAFE, the words SELECT A WORKOUT, PRESS QUICKSTART, OR ENTER TO BEGIN scroll across the upper text display.
38 Operating and Maintaining the P30 Console Starting a Preset Programmed Workout Preset workouts are a great way to tailor your workouts to your fitness goals, stay challenged, and add variety to your sessions. Most P30 equipment contains multiple preset workouts.
39 Starting a Workout To choose a language setting before you begin exercising: 1. From the Welcome banner, press OPTIONS. 2. Press OPTIONS again to choose the Language option, and press OK. 3. Use the Up and Down arrows to navigate the list of available languages. To select a language, press OK. Language choices are: English, Deutsch, Espanol, Francais, Nederlands, Portugues, Rucckijj, and Italiano. 4. To continue to the next option category, press the Up or Down arrows.
40 Operating and Maintaining the P30 Console Pausing and Resuming an Exercise Session When you interrupt a workout, the equipment responds in one of two ways, depending on how it is powered. Paused (Externally Powered Equipment) When the session is paused, the belt speed is slowly reduced to zero, or the resistance is slowly reduced to the minimum. The lift motor is turned off leaving the incline or crossramp at its current position. Data entry is canceled.
41 Starting a Workout Ending a Session Cooling down is an important aspect of your workout because it helps reduce muscle stiffness and soreness by transporting excess lactic acid out of the working muscles. In addition, a three to five minute cool down allows your heart rate to return to its normal, resting state. At the end of your workout, a Summary screen displays your average heart rate during your workout and your accumulated workout metrics.
42 Operating and Maintaining the P30 Console Accumulated Metrics describe the overall performance throughout the entire exercise session.
43 Starting a Workout Interval The Interval workout is primarily for conditioning your cardiovascular system. This workout is designed to raise and lower your heart rate in a repeating fashion for a user-defined period of time by alternating rest and work intervals. Workout intensity is adjustable. Weight Loss The workout time is fixed at 28 minutes. The workout consists of four intervals, each lasting eight minutes. You can change the resistance at any time during the work interval.
44 Operating and Maintaining the P30 Console City Steps (Climber only) The City Steps Program increases and decreases your step rate in stages. In each stage, the rate gradually rises to a peak and then falls quickly back to the starting rate. This pattern is repeated. You can override the settings for each column. Any increase or decrease made in one program segment will increase or decrease all remaining portions by the same amount.
Chapter 5 Maintenance To keep the equipment functioning properly, perform the minor maintenance tasks in this section at the intervals suggested. Failure to maintain the equipment as described in this section could void the Precor Limited Warranty. DANGER To reduce the risk of electrical shock, always disconnect the equipment from its power source before cleaning it or performing any maintenance tasks. If the equipment uses an optional power adapter, disconnect the adapter.
46 Notes: Operating and Maintaining the P30 Console
Notes Notes: 47
48 Notes: Operating and Maintaining the P30 Console
Operating and Maintaining the P30 Console Precor Incorporated 20031 142nd Avenue NE P.O.
Assembling and Maintaining AMT® 800-Series Adaptive Motion Trainers® Precor Incorporated 20031 142nd Avenue NE P.O.
Edition Information ASSEMBLING AND MAINTAINING AMT 800-SERIES ADAPTIVE MOTION TRAINERS P/N 300710-341 rev G Copyright © July 2011 Precor Incorporated. All rights reserved. Specifications subject to change without notice. Trademark Note Precor, AMT, and EFX are registered trademarks and Preva is a trademark of Precor Incorporated. Other names in this document may be the trademarks or registered trademarks of their respective owners.
Important Safety Instructions Read all instructions in the documentation provided with your exercise equipment, including all assembly guides, user guides, and owner’s manuals, before installation of this device. The display apparatus (hereinafter referred to as the console) is intended to be shipped with new Precor exercise equipment (hereinafter referred to as the base unit). It is not packaged for individual sale.
4 Assembling and Maintaining AMT 800-Series Adaptive Motion Trainers Do not allow children, or people unfamiliar with the operation of this equipment, on or near it. Do not leave children unsupervised around the equipment. Make sure all users wear proper exercise clothing and shoes for their workouts and avoid loose or dangling clothing. Users should not wear shoes with heels or leather soles, and they should check the soles of their shoes to remove any dirt and embedded stones.
Important Safety Instructions 5 Proper Location for Equipment For all equipment other than treadmills: Locate at least 40 inches (1 meter) away from walls or furniture on either side of the equipment, and 40 inches (1 meter) away from objects behind the equipment. For treadmills: Locate at least 40 inches (1 meter) away from walls or furniture on either side of the treadmill, and at least 80 inches (2 meters) away from objects behind the treadmill.
6 Assembling and Maintaining AMT 800-Series Adaptive Motion Trainers Do not operate the equipment where aerosol (spray) products are being used or where oxygen is being administered. Do not use outdoors. Do not attempt to service the equipment yourself, except to follow the maintenance instructions in this manual. Never drop or insert objects into any opening. Keep hands away from moving parts. Do not set anything on the stationary handrails, handlebars, control console, or covers.
Important Safety Instructions 7 Product Recycling and Disposal This equipment must be recycled or discarded according to applicable local and national regulations. Product labels, in accordance with European Directive 2002/96/EC concerning waste electrical and electronic equipment (WEEE), determine the framework for the return and recycling of used equipment as applicable throughout the European Union.
8 Assembling and Maintaining AMT 800-Series Adaptive Motion Trainers Federal Communications Commission, Part 15 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial installation.
Important Safety Instructions European Applications CE compliance is claimed to the following directives: 1999/5/EC R&TTE Directive 2006/95/EC LVD Directive 2002/95/EC RoHS Directive Directive compliance has been verified to the following standards: EN 55022 EN 300 330-1 V1.5.1 EN 300 330-2 V1.3.1 EN 301 489-3 V1.4.1 EN 301 489-1 V1.8.
10 Assembling and Maintaining AMT 800-Series Adaptive Motion Trainers Radio Frequency Interference (RFI) This Precor exercise equipment conforms to the following national standards defining acceptable limits for radio frequency interference (RFI). Federal Communications Commission, Part 15 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
Important Safety Instructions 11 Electrical Recommendations: All Equipment Excluding Treadmills Note: This is a recommendation only. NEC (National Electric Code) guidelines or local region electric codes must be followed. For equipment fitted with a P80 console or Personal Viewing System (PVS) screen a separate power connection is required. For a 20 amp branch circuit up to 10 screens can be connected.
12 Assembling and Maintaining AMT 800-Series Adaptive Motion Trainers Obtaining Updated Documentation Current documentation for Experience Series consoles and Preva Networked Fitness software is available at http://www.precor.com/productmanuals. You may want to check in for updated information from time to time as the universe of Preva features expands.
Table of Contents Important Safety Instructions .................................................... 3 Safety Precautions ................................................................................ 3 Educating Users .................................................................................... 6 Hazardous Materials and Proper Disposal .................................... 6 Product Recycling and Disposal .......................................................
14 Assembling and Maintaining AMT 800-Series Adaptive Motion Trainers Maintenance .............................................................................. 39 Daily Cleaning ..................................................................................... 39 Daily Inspection .................................................................................. 40 Weekly Maintenance ......................................................................... 41 Monthly Maintenance .......................
Chapter 1 Assembling the AMT Important: The instructions in the following procedures are described from the perspective of a person standing directly in front of the equipment (that is, on the opposite side of the control console from a person using the equipment). These descriptions may not match the names of certain parts in the parts list, because such parts are named relative to the back of the equipment.
16 Assembling and Maintaining AMT 800-Series Adaptive Motion Trainers Hardware Kit (not to scale) The hardware kit shipped with this equipment contains the fasteners and other hardware components shown in the following table. Before you begin assembly, make sure that your hardware kit is complete. If not, please contact Precor Customer Support.
17 Assembling the AMT Required Tools ⁵₁₆-inch hex wrench ⁵₃₂-inch hex wrench #2 Phillips screwdriver Rubber mallet SAE standard socket set Wire cutter Torque wrench (calibrated in inch-pounds) Performing the Assembly DANGER Do not attempt to connect electrical power until all assembly procedures are complete and the console is properly installed. Follow these steps to assemble the AMT base unit. To begin assembly: 1.
18 Assembling and Maintaining AMT 800-Series Adaptive Motion Trainers 3. Insert the end caps into the front frame tube. If necessary, use a rubber mallet to tap them into place. Figure 2: Removal of unit from pallet and insertion of end caps To attach the handlebars: 1. Slide a plastic boot onto each handlebar. Figure 3: Boot attachment 2. Use the following graphic to determine the proper position of the handlebars.
19 Assembling the AMT Note: When the handlebars are mounted correctly, each bends slightly outward. Figure 4: View of handlebar placement 3. Attach the handlebars using four ⁵₁₆-inch x 1¾-inch hex head screws, eight ⁵₁₆-inch washers, and four ⁵₁₆-inch locknuts. Using a torque wrench, tighten the fasteners with 180 to 200 inch-pounds of torque. Figure 5: Handlebar attachment 4.
20 Assembling and Maintaining AMT 800-Series Adaptive Motion Trainers Removing Access Covers With its access covers removed, the AMT provides easy access to its cables and internal components. Tip: In the following procedure, set aside the covers and their mounting hardware in groups, in the order in which you remove them. This simplifies reinstallation later. To remove the access covers: 1.
Assembling the AMT 21 Threading the Cables Depending on the model of console you are installing and the options it includes, you will need to install one or more of the following cables: Television (coaxial with F connectors) Power Ethernet Precor recommends threading new cables from the top down, to take advantage of gravity. A fish tape (a thin metal strip with a hook or clasp on one end, available from professional hardware vendors) can be helpful during this procedure.
22 Assembling and Maintaining AMT 800-Series Adaptive Motion Trainers Connect … To … The console power cable The power cable assembly The Ethernet cable The eight-connector modular jack on the jack panel The television cable The coaxial connector on the jack panel Note: This cable must be wrench tightened. 4. Repeat steps 1 through 3 until all three cables are completely installed. 5. Insert all cables into the cable clips on the center frame pillar just below the bottom of the center column.
23 Assembling the AMT To level the AMT: 1. Gently rock the AMT while standing on one of its foot plates and grabbing the opposite handlebar. First stand on the left foot plate and grab the right handlebar to rock the AMT, then repeat the step while standing on the right foot plate and holding the left handlebar. If there is any movement, ask your assistant to tip the unit on its side while you locate the adjustable feet. 2. Reposition the adjustable feet as needed.
24 Assembling and Maintaining AMT 800-Series Adaptive Motion Trainers Breaking in the Equipment Precor equipment does not require an actual break-in period. However, moving components such as belts, gears, and bearings can settle while the equipment is being stored or shipped. This can cause the equipment to operate with a small amount of roughness or noise when it starts up for the first time. The equipment usually returns to smooth operation after a day or two of normal use.
Chapter 2 Installing the Console To make installation easier, all Precor Experience Series consoles use the same mounting hardware and connector locations whenever possible. The installation sequence for any of them is as follows: Threading the cable assembly Connecting cables Completing the installation (tightening the mounting screws and attaching the back cover) The following sections describe how to perform these tasks.
26 Assembling and Maintaining AMT 800-Series Adaptive Motion Trainers Important: Before you begin the following procedure, remove the rear cover from the control console. To remove the cover, use your fingernails to pry the lower edge loose, then swing the cover up and out as shown in the following illustration. Figure 9: Removing the access cover from the P80 console To thread the cable assembly: 1.
27 Installing the Console 3. Rest the console on the console mount so that the notch on the bottom of the console’s back plate rests on the rectangular hook at the bottom of the console mount, as shown in the following figure. Figure 10: Console positioning on base unit 4. Tilt the console forward until it stops. Use one hand to steady the console in this position, or ask your assistant to do so.
28 Assembling and Maintaining AMT 800-Series Adaptive Motion Trainers Connecting Cables (P80) After the console has been seated, separate the individual cables out of the end of the cable assembly and attach them to the appropriate circuit connectors inside the console. Refer to the following diagram and table to identify the cables and connectors.
29 Installing the Console Table 1.
30 Assembling and Maintaining AMT 800-Series Adaptive Motion Trainers Connecting the Television Cable The console’s television tuner is mounted inside the console’s back plate. The tuner includes a short cable adapter that allows the television cable to be connected outside the back plate. To connect the television cable: 1. Pull the cable out through the lower right corner of the back plate. 2. Route the cable counterclockwise around the outside of the back plate. 3.
Installing the Console 31 Connecting the Ethernet and Base Unit Data Cables Both the Ethernet and base unit data cables pass through the cutaway opening at the upper right corner of the back plate and connect to nearby modular jacks in the console. Because of this, it is important to exercise caution when connecting the cables. The black Ethernet cable connects to a jack just underneath the perforated metal bracket at the very top of the opening in the console.
32 Assembling and Maintaining AMT 800-Series Adaptive Motion Trainers Connecting the Heart Rate Sensor Cable The heart rate sensor cable passes through the cutaway opening at the upper left corner of the back plate, then down to the small circuit board at the lower left of the console. The following illustration shows how the cable should look once it is installed. Figure 14: Connecting the heart rate cable Connecting the Power Cable A power splitter cable provides power to the tuner and display.
Installing the Console 33 Completing the Console Installation (P80) Before you complete the final installation steps, double-check the connections you have made. Make sure that all cables are fully and securely connected, and that any unneeded cables are tied back properly. To complete the installation: 1. Feed extra cable back into the neck tube. 2.
34 Assembling and Maintaining AMT 800-Series Adaptive Motion Trainers To thread the cable assembly: 1. Make sure that as much of each cable as possible passes through the opening in the middle of the console mount on the base unit. 2. Position the console over the console mount. 3. Rest the console on the console mount so that the notch on the bottom of the console’s back plate rests on the rectangular hook at the bottom of the console mount, as shown in the following figure.
Installing the Console 35 Connecting Cables (P30) After the console has been seated, separate the individual cables out of the end of the cable assembly and attach them to the appropriate circuit connectors inside the console. Refer to the following diagram and table to identify the cables and connectors.
36 Assembling and Maintaining AMT 800-Series Adaptive Motion Trainers Table 2.
37 Installing the Console Connecting Cables (P20) After the console has been seated, separate the individual cables out of the end of the cable assembly and attach them to the appropriate circuit connectors inside the console. Refer to the following diagram and table to identify the cables and connectors. Figure 18: Cable connections, P20 console Table 3.
38 Assembling and Maintaining AMT 800-Series Adaptive Motion Trainers Completing the Console Installation(P30 and P20) Before you complete the final installation steps, double-check the connections you have made. Make sure that all cables are fully and securely connected, and that any unneeded cables are tied back properly. To complete the installation: 1. Feed extra cable back into the neck tube. 2.
Chapter 3 Maintenance To keep the equipment functioning properly, perform the minor maintenance tasks in this section at the intervals shown on the maintenance checklist. Failure to maintain the equipment as described in this section could void the Precor Limited Warranty. DANGER To reduce the risk of electrical shock, always disconnect the equipment from its power source before cleaning it or performing any maintenance tasks.
40 Assembling and Maintaining AMT 800-Series Adaptive Motion Trainers Alternatively, you can clean the equipment with Athletix fitness equipment cleaning wipes (for more information, visit www.athletixproducts.com) CAUTION: Read and follow the manufacturer’s instructions, particularly dilution instructions, before using any cleaner on Precor fitness equipment.
41 Maintenance Weekly Maintenance Perform the following maintenance tasks every week: 1. Disconnect the external power supply. 2. Clean the floor under the equipment using a vacuum cleaner or a damp mop. 3. Verify that the stair-arm bumpers are aligned correctly. 4. When the floor is completely dry, reconnect the power (if necessary). 5. Test all console functions, including heart rate monitoring features. 6. Verify that the unit sits squarely on the floor.
42 Assembling and Maintaining AMT 800-Series Adaptive Motion Trainers Storing the Chest Strap If you purchased the optional heart rate chest strap, store it in a place where it remains free of dust and dirt (for example, in a closet or drawer). Be sure to protect the chest strap from extremes in temperature. Do not store it in a place that may be exposed to temperatures below 32° F (0° C). To clean the chest strap, use a sponge or soft cloth dampened in mild soap and water.
Chapter 4 Self-Powered Features Important: This chapter of the manual describes Precor fitness equipment that can operate without being connected to AC power. This includes units equipped with P30 or P20 consoles. However, P80 consoles must be connected to AC power through their power supplies to operate. For this reason, this chapter does not apply to units equipped with P80 consoles. On self-powered equipment, the system initializes and displays the Welcome screen when a user starts exercising.
44 Assembling and Maintaining AMT 800-Series Adaptive Motion Trainers Informational Displays Prior to Shutdown The equipment saves its battery charge by moving into a shutdown mode. If the user does not maintain the minimum rate of motion, a 30-second shutdown process begins. In this mode, the console displays a countdown indicator and ignores all keypresses. If no movement is detected or the rate of motion remains below the minimum, the indicator changes as the countdown continues.
Self-Powered Features 45 Using the Optional Power Adapter After connecting the power adapter to the equipment, plug the opposite end into the appropriate power source (120 V or 240 V). CAUTION: When the optional power adapter is in use, make sure that the power supply cord does not create a safety hazard. Keep it out of the way of traffic and moving parts. If the power supply cord or power conversion module is damaged, it must be replaced.
46 Assembling and Maintaining AMT 800-Series Adaptive Motion Trainers Replacing the Battery The equipment’s battery is built to last for a long time. However, if you feel that the battery may need replacing, check with an authorized service technician. Refer to Obtaining Service. CAUTION: The battery stored inside the equipment contains hazardous materials and must be disposed of according to Hazardous Waste Regulations. Refer to Hazardous Materials and Proper Disposal.
Chapter 5 Commercial Cardiovascular Equipment Limited Warranty PLEASE READ THESE WARRANTY TERMS AND CONDITIONS CAREFULLY BEFORE USING YOUR PRECOR INCORPORATED PRODUCT. BY USING THE EQUIPMENT, YOU ARE CONSENTING TO BE BOUND BY THE FOLLOWING WARRANTY TERMS AND CONDITIONS. Limited Warranty. Precor Incorporated warrants all new Precor products to be free from defects in materials and manufacture for the warranty periods set forth below.
48 Assembling and Maintaining AMT 800-Series Adaptive Motion Trainers Options / Accessories Many options or accessories have components that are connected internally or mounted inside the electronic console. The following guidelines determine the warranty for these components.
Commercial Cardiovascular Equipment Limited Warranty 49 This Limited Warranty shall not apply to: 1. Software version upgrades. 2. Software defects that do not materially and negatively affect the normal performance of the product under normal conditions of use. 3.
50 Assembling and Maintaining AMT 800-Series Adaptive Motion Trainers EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.
Notes Notes: 51
52 Notes: Assembling and Maintaining AMT 800-Series Adaptive Motion Trainers
Assembling and Maintaining AMT® 800-Series Adaptive Motion Trainers® Precor Incorporated 20031 142nd Avenue NE P.O.
