S3.
Important Safety Instructions Before beginning any fitness program, you should obtain a complete physical examination from your physician. Il est conseillé de subir un examen médical complet avant d’entreprendre tout programme d’exercise. Si vous avez des étourdissements ou des faiblesses, arrêtez les exercices immédiatement. When using exercise equipment, basic precautions should always be taken, including the following: • Read all instructions before using the Leg Press Option.
S3.25 Leg Press Option Assembly Instructions Table of Contents Important Safety Instructions ............................................................... 2 Personal Safety During Assembly .................................................................................. Obtaining Service .......................................................................................................... 2 2 1 2 Before You Begin ...................................................................................
S3.25 Leg Press Option Assembly Instructions 1 Before You Begin Thank you for purchasing the Leg Press Option for your Precor equipment. This option will add a new dimension to your strength-training regimen. For proper installation, please read this guide thoroughly and follow the assembly instructions. Unpacking the Equipment The Leg Press Option is carefully tested and inspected before shipment. Precor ships the unit in several pieces that require assembly.
S3.25 Leg Press Option Assembly Instructions 2 Installation Requirements Assembly Tips Follow these installation requirements when assembling the unit: • • Preparations CAUTION: To set up this equipment, you will need assistance. Do not attempt assembly by yourself. You must review and follow the instructions in this guide. If you do not assemble and use the Leg Press Option according to the following guidelines, you could void the Precor limited warranty.
S3.25 Leg Press Option Assembly Instructions 3 Assembly Instructions Assembly of the Leg Press Option takes professional installers about 1 hour to complete. If this is the first time you have assembled this type of equipment, plan on significantly more time. Professional installers are highly recommended! CAUTION: Obtain assistance! Do not attempt to assemble the Leg Press Option by yourself. Because of the weight and size of the Leg Press Option, you could be injured or damage the equipment.
S3.25 Leg Press Option Assembly Instructions 1. Remove the Shroud Important: For ease of assembly, the fasteners and hardware for each step are labeled and packaged in separate bags. Top Beam Note: If you are assembling the Leg Press Option along with your S3.25, go directly to Step 2. Before you can attach the Leg Press Option to the unit, you must remove the Shroud. Notch in Shroud fits around Top Beam fastener A.
S3.25 Leg Press Option Assembly Instructions 2. Attach the Cross Brace to the S3.25 Note: If you are assembling the Leg Press Option along with the S3.25, you should complete Step 10 in the S3.25 Assembly and Maintenance Guide before attaching the Cross Brace. A. Align the Cross Brace to the S3.25 Rear Upright and secure it using two 3-inch bolts four washers two locknuts Wrench tighten. A 1 Step 2. Attach the Cross Brace to the S3.
S3.25 Leg Press Option Assembly Instructions 3. Assemble the Frame A. With someone helping you, lift the Seat Frame upright. Have your assistant hold it in place while you attach the Cross Brace in the next step. Backpad Support B. Attach the Cross Brace to the holes found at the front of the Seat Frame using two 3-inch bolts four washers two locknuts Wrench tighten.
S3.25 Leg Press Option Assembly Instructions D. Assemble the Footrest by resting the Pivot Arm on the Rubber Bumper. Make sure that the red arrow on the back of the Footrest points toward the ceiling. E 2 - large ½" x 3¼" bolts 4 - ½" diameter washers 2 - large ½" lock nuts E. Attach the Footrest to the Pivot Arm and Pivot Tube using two large ½-inch by 3-¼-inch bolts four ½-inch-diameter washers two large ½-inch locknuts Wrench tighten enough to allow free movement of the Pivot Arm. F.
S3.25 Leg Press Option Assembly Instructions 4. Assemble the Seat Pads A. Attach one of the Seat Pads to the Seat Bracket Support using two 1¼-inch bolts two washers Wrench tighten. B Seat Bracket Support Lift the Pop Pin to slide the back rest Seat Pad used as a back rest B. Lift the Pop Pin and slide the Seat Pad out of the way to assemble the other Seat Pad. C. Attach the remaining Seat Pad to the Seat Frame using two 3-inch bolts two washers Wrench tighten.
S3.25 Leg Press Option Assembly Instructions 5. Route the Cable Push the Pivot Arm forward As you route the Cable through the pulleys on the Leg Press Option, wrench tighten the fasteners on each pulley as you go. Make sure that the Cable slides freely along the pulley (and beneath the cable retainer). Make sure that you are using the correct Cable before you tighten the fasteners. A.
S3.25 Leg Press Option Assembly Instructions 6. Assemble the Cable and Pulleys Rear Upright You can identify Cables by the white numbers placed at the end of the Cable. A. Place Leg Press Option Cable 40538-101 between a cable retainer and one 3½-inch pulley. Attach the pulley to the Lower Pulley Bracket located at the base of the Rear Upright using one 2-inch bolt two washers one locknut Wrench tighten.
S3.25 Leg Press Option Assembly Instructions C. Reattach the end of the original Surgical Tube from the Cable Tree to its prior location and place the new Surgical Tube that came with the Leg Press Option to the outside of the Top Beam using one 4-inch bolt two washers two ½-inch barrel spacers one locknut Wrench tighten. C New Surgical Tube D. Place the ball-end of Leg Press Option Cable 40538101 up through the Cable Tree and place it securely in the U-clip. E.
S3.25 Leg Press Option Assembly Instructions 7. Replace the Shroud A. Pick up the Shroud and fasteners from the location where you left them in Step 4B. Top Beam B. Replace the Shroud by realigning the mounting holes and inserting six 2¾-inch bolts six washers six locknuts Wrench tighten. Notch in Shroud fits around Top Beam fastener A Replace Shroud B 1 Step 7.
S3.25 Leg Press Option Assembly Instructions 4 A Top Cap Weight Adjustments After the Leg Press Option is assembled, you should check the Cables for proper tension. These are some obvious signs that cable problems exist: Top Weight ✔ Excess slack exists in the Cable. ✔ The Top Cap Weight does not rest squarely on the Weight Stack. Weight Pin ✔ The Cable rubs the inside edges of the pulleys. CAUTION: Take the time to perform the following steps.
S3.25 Leg Press Option Assembly Instructions Weight then further adjustments are needed. Continue with steps 2 and 3. 2. Rotate the Cam Washer A If the Top Cap Weight does not rest on the Top Weight, you must make further adjustments. Top Cap Weight A. Remove excess tension from the Cable by placing the Weight Pin into the Selector Stem just under the Top Cap Weight. B. To tighten or loosen the Cable tension, rotate the Cam Washer. Top Weight C.
S3.25 Leg Press Option Assembly Instructions 3. Adjust the Rubber Bumper on the Leg Press Option A Push the Pivot Arm up to adjust the Rubber Bumper If the Top Cap Weight still does not rest on the Top Weight, you can make one final adjustment. A. If the Cable tension still needs adjusting, push the Pivot Arm up so that you can adjust the Rubber Bumper on the Leg Press Option. B. Rotate the Rubber Bumper up or down to tighten or loosen the Cable tension.
Residential Equipment Limited Warranty Precor Incorporated warrants that all new Precor products are free of manufacturing defects in workmanship and materials. Parts repaired or replaced under the terms of this warranty will be warranted for the remainder of the original warranty period only. This warranty becomes effective at the invoice date of the original purchase. Elliptical Fitness Crosstrainers and Motorized Treadmills (excluding EFX5.17 and Treadmills: 9.2 and 9.
Please fill out the Warranty Registration and mail it to Precor. S3.25 Leg Press Option Specifications Length: 60 inches (152 cm) Height: 33 inches (84 cm) Width: 30 inches (76 cm) ▼ Shipping weight: 125 lb (57 kg) Precor Incorporated 20031 142nd Avenue NE P.O. Box 7202 Woodinville, WA USA 98072-4002 Warranty Registration Card Precor Incorporated 20031 142nd Avenue NE P.O. Box 7202 Woodinville, WA USA 98072-4002 Precor and Pacific Fitness are registered trademarks of Precor Incorporated.
