Operating and Maintaining the P10 Console Precor Incorporated 20031 142nd Avenue NE P.O.
Operating and Maintaining the P10 Console
Edition Information OPERATING AND MAINTAINING THE P10 CONSOLE P/N 302291-102 rev B Copyright © June 2014 Precor Incorporated. All rights reserved. Specifications subject to change without notice. Trademark Note Precor, AMT, EFX, and Preva are registered trademarks of Precor Incorporated. Other names in this document may be the trademarks or registered trademarks of their respective owners.
Important Safety Instructions Important: Save these instructions for future reference. Read all instructions in the documentation provided with your exercise equipment, including all assembly guides, user guides, and owner’s manuals, before installation of this device. Note: This product is intended for commercial use. The display apparatus (hereinafter referred to as the console) is intended to be shipped with new Precor exercise equipment (hereinafter referred to as the base unit).
4 Operating and Maintaining the P10 Console Safety Precautions Always follow basic safety precautions when using this equipment to reduce the chance of injury, fire, or damage. Other sections in this manual provide more details of safety features. Be sure to read these sections and observe all safety notices. These precautions include the following: Read all instructions in this guide before installing and using the equipment and follow any labels on the equipment.
Important Safety Instructions 5 Never leave the equipment unattended when it is plugged in. Unplug the equipment from its power source when it is not in use, before cleaning it, and before providing authorized service. Note: The optional power adapter is considered a power source for self-powered equipment. Use the power adapter provided with the equipment. Plug the power adapter into an appropriate, grounded power outlet as marked on the equipment.
6 Operating and Maintaining the P10 Console SPACING—The below minimum spacing recommendations are based on a combination of the ASTM (U.S.) voluntary standards and EN (European) regulations as of October 1, 2012, for access, passage around, and emergency dismount: – Treadmills—a minimum of 0.5 m (19.7 in.) on each side of the treadmill and 2 m (78 in.) behind the machine. – Cardio equipment other than treadmills—a minimum of 0.5 m (19.7 in.) on at least one side, and 0.5 m (19.7 in.
Important Safety Instructions 7 Maintain the equipment to keep it in good working condition, as described in the Maintenance section of the owner’s manual. Inspect the equipment for incorrect, worn, or loose components, and then correct, replace or tighten prior to use. If you plan to move the equipment, obtain help and use proper lifting techniques. Equipment Weight Restrictions: Do not use the treadmill if you weigh more than 400 pounds (180 kg).
8 Operating and Maintaining the P10 Console Hazardous Materials and Proper Disposal The batteries within self-powered equipment contain materials that are considered hazardous to the environment. Federal law requires proper disposal of these batteries. If you plan to dispose of your equipment, contact Precor Commercial Products Customer Support for information regarding battery removal. Refer to Obtaining Service.
9 Important Safety Instructions Regulatory Notices for Cardiovascular Exercise Equipment The regulatory information in this section applies to the exercise equipment and its control console. Safety Approvals for Cardiovascular Equipment Precor equipment has been tested and found to comply with the following applicable safety standards.
10 Operating and Maintaining the P10 Console Industry Canada This device complies with RSS-210:2007 of the Spectrum Management & Telecommunications Radio Standards Specification. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This Class A digital apparatus complies with Canadian ICES-003.
Important Safety Instructions 11 Electrical Recommendations: 120 V and 240 V Treadmills Note: This is a recommendation only. NEC (National Electric Code) guidelines or local region electric codes must be followed. You should have received a power cable that meets your local electrical code requirements along with the equipment. Precor treadmills must be connected to a 20 amp individual branch circuit that can be shared only with one PVS.
12 Operating and Maintaining the P10 Console Electrical Recommendations: All Equipment Excluding Treadmills Note: This is a recommendation only. NEC (National Electric Code) guidelines or local region electric codes must be followed. For equipment fitted with a P80 console or Personal Viewing System (PVS) screen a separate power connection is required. For a 20 amp branch circuit up to 10 screens can be connected.
Table of Contents Important Safety Instructions .................................................... 3 Safety Precautions ................................................................................ 4 Hazardous Materials and Proper Disposal .................................... 8 Product Recycling and Disposal ....................................................... 8 Regulatory Notices for Cardiovascular Exercise Equipment ..................................................................................
14 Operating and Maintaining the P10 Console Starting a Workout ................................................................... 37 Starting a Preset Programmed Workout ..................................... 38 Pausing and Resuming an Exercise Session ................................ 38 Ending a Session ................................................................................. 39 Workouts ...............................................................................................
Chapter 1 Getting Started The P10 console offers administrators the ability to set default values that meet their specific needs. These values include items like language, units of measure, and setting a maximum allowed workout time for each piece of equipment. Activating the Console for Self-Powered Equipment Precor equipment is either self-powered or externally powered using an optional power adapter. Self-powered equipment requires the user exercise to initialize the console.
16 Operating and Maintaining the P10 Console Optional Use of the Power Adapter An optional AC power adapter provides sustained power to the equipment. This adapter allows you to change settings without having to pedal the equipment. To purchase the power adapter, contact your dealer. If you purchase the optional power adapter, you must also purchase the internal cable kit. The kit supplies the cable, bracket, and fasteners that connect the power adapter to the lower electronics board.
17 Getting Started Identifying Parts of the Console The following figure provides information about the console keys. The number and actions of the console keys may differ slightly depending on the type of equipment. Figure 4: P10 console keys Table 1. Parts of the console Number Name Number pad Details Enter numerical information such as age, weight, and passwords. You can also enter and change channels using the number pad. • Press Clear to delete the numbers you entered.
18 Operating and Maintaining the P10 Console Number Name Workouts Pause Details Examples of workouts: • Manual • Heart Rate • Interval • Weight Loss • Variety • Performance Use to pause or end a workout session. OK and Up/Down Use to navigate options and settings. arrows Quick Start • Calories • Time Elapsed • Time Remaining • Watts (bike) • Time (bike) Press Quick Start to begin exercising. Use the ▲ or ▼ arrows to change what information is displayed.
Chapter 2 Setting Up the Console Use the System mode to configure settings in ways that benefit your users and your facility. The System menu is visible only to administrators and registered service technicians. Changes made to these settings are saved to the fitness equipment. The System Settings categories are: Club Parameters Informational Display System Settings System Setting features remain hidden from club patrons and can only be accessed using special keypresses.
20 Operating and Maintaining the P10 Console CAUTION: If you change the Unit of Measure display on the treadmill, check the speed setting to verify that it is correct. To view the Club Settings: 1. At the Welcome banner, press Pause. 2. Press the following number keys in sequence to enter the password: 5651565 3. Press OK. The Set Club Parameters banner appears. Table 2.
Setting Up the Console 21 Club Parameters Use the following information to customize the equipment for your setting. Note: When you make changes to the club parameters, the new settings replace the factory default settings. Safety Code (Treadmill only) Value: Enabled or Disabled (Default: Disabled) When the equipment is shipped from the factory, the safety code protection feature is disabled.
22 Operating and Maintaining the P10 Console Set Max Workout Time (All Equipment) Value Range: 1 to 240 minutes (Default: 60 minutes) You can set a maximum workout time per session. Choose a time limit between 1 and 240 minutes, or select No Limit if you do not want to set a time limit. For example, if you set the time limit to 20 minutes, users can only enter a workout time between 1 and 20 minutes.
23 Setting Up the Console Set Speed Limit (Treadmill only) Value Range: Full speed range of equipment (Default: Maximum speed) This setting limits how fast the running belt moves and, consequently, the number of speed settings that are available to the user. Use it to set the maximum speed that a user can enter when using the equipment. The speed is displayed in miles per hour (mph) or kilometers per hour (kph) depending upon the units of measure (U.S. Standard or Metric) selected earlier.
24 Operating and Maintaining the P10 Console Autostop Configure (Treadmill only) Value: On or Off (Default: On) Set to On to bring the treadmill to a gradual stop when no user is on the equipment. This can occur if a user steps off the equipment during a workout and does not turn it off. Set Crossramp Auto-level (EFX only) Value Range: 0 to 20 (Default: 10) Use this setting to choose a specific ramp incline so that the EFX automatically returns to that incline at the end of a workout session.
Setting Up the Console 25 Viewing the Informational Displays Information Display settings are values that provide you with information about the equipment. Types of information contained in this setting group include, an event (error) log, software and equipment serial numbers, and usage information. To view the System settings: 1. At the Welcome banner, press Pause. 2. Press the following number keys in sequence to enter the password: 65 3. Press OK.
26 Operating and Maintaining the P10 Console Use the following table to set up customized Informational Display values. Table 3. Informational Displays values Product Value Information provided All ODOMETER Correlates to the type of equipment and the standard of units, U.S. or Metric, selected in the programs. AMT All BELT USAGE HOUR METER • Treadmill and AMT: Displays the number of cumulative miles or kilometers logged to date. In addition, the AMT displays the number of vertical strides.
27 Setting Up the Console Product Value Information provided All UPPER BASE SW PART NUMBER Displays the upper base application software version. All LOWER BASE SW PART NUMBER Displays the lower application software version. All METRICS BOARD Displays the software number on the Metrics Board. All SERIAL NUMBER Displays the model and type of equipment. All USAGE LOG • Displays the number of times each workout has been used and displays the associated cumulative minutes.
28 Operating and Maintaining the P10 Console The following table contains a list of events detectable by the software. Table 4.
29 Setting Up the Console Event Number Description of Event 32 Communication event upper board to lower board 33 Incorrect communications event lower board to upper board 35 Excessive AC input current (instantaneous; treadmill only) 36 Excessive AC input current (sustained / circuit breaker trip protection; treadmill only) 37 E-STOP error (treadmill only) 40 Lift motion not detected 42 Lift position value out of range 43 Zero switch not found 44 Un-commanded lift motion 45 Lift going
30 Operating and Maintaining the P10 Console Event Number Description of Event 81 Phase C missing (incline control; treadmill only) 82 Phase A or B missing (speed control; treadmill only) 83 Phase C missing (speed control; treadmill only) 85 No dynamic break resistor detected, or dynamic break resistor is detected as an open circuit, at startup time (treadmill only) 86 Old console detected on new equipment (treadmill only) 87 New console installed on older equipment (treadmill only) 88 Moto
Chapter 3 Introducing Users to the P10 Console CAUTION: Before beginning any fitness program, see your physician for a thorough physical examination. Seek advice from your physician to learn the target heart rate appropriate for your fitness level. The P10 console offers an easy-to-follow display and multiple workouts to help people meet their exercise needs.
32 Operating and Maintaining the P10 Console When gripping the sensors, do not grip tightly. Keep a loose, cupping hold. Holding the grips tightly can affect the reading. As you work out, your perspiration will help transmit your heart rate signal. If you have difficulty using the handheld grips to determine your heart rate, try the sensors again later in the workout to see if you can obtain a heart rate signal.
Introducing Users to the P10 Console 33 Using a Chest Strap Transmitter WARNING Signals used by the chest strap transmitter (or heart rate strap) may interfere with pacemakers or other implanted devices. Consult your physician and the manufacturers of your chest strap transmitter and implanted device before using a chest strap transmitter. Wearing a chest strap transmitter during your workout provides steady heart rate information.
34 Operating and Maintaining the P10 Console Using the Treadmill Safety Clip The treadmill is equipped with three different stop functions, which behave as follows: If the user … Then the treadmill belt … And the console … Slows to a Pulls on the lanyard attached to the safety stop clip and trips the restart switch Shows the words PUSH THE RESET SWITCH. On some console models, an arrow points toward the Restart switch.
Introducing Users to the P10 Console 35 Instruct users on how important it is to use the safety clip while exercising on the treadmill, and demonstrate how they should attach it to their clothing near the waistline. If the restart switch trips during exercise, perform the following steps: 1. Reattach the safety clip if necessary. 2. Press the restart switch down until it clicks, returning it to its normal position. Note: If the restart switch trips, all information about the current workout is deleted. 3.
36 Operating and Maintaining the P10 Console Treadmill Auto Stop™ (Automatic Stop) Function Important: The default setting for this feature is ON. An administrator can turn off this feature in the System Settings; however, Precor recommends it remain ON. The Auto Stop™ (Automatic Stop) feature is designed to bring the treadmill to a gradual stop when it is not in use. This might occur if a user steps off the treadmill before the end of a workout and leaves the treadmill running.
Chapter 4 Starting a Workout CAUTION: If you are using a treadmill, be sure to attach the security clip to your clothing before starting your workout. The equipment is in the Welcome state when the words SELECT A WORKOUT OR PRESS QUICKSTART TO BEGIN scroll across the scrolling text display. If the equipment is connected to CSAFE, the words SELECT A WORKOUT, PRESS QUICKSTART, OR ENTER TO BEGIN scroll across the text display.
38 Operating and Maintaining the P10 Console Starting a Preset Programmed Workout Preset workouts are a great way to tailor your workouts to your fitness goals, stay challenged, and add variety to your sessions. These workouts are arranged in the following categories: Manual Heart Rate Interval Weight Loss Variety Performance Pausing and Resuming an Exercise Session When you interrupt a workout, the equipment responds in one of two ways, depending on how it is powered.
39 Starting a Workout Ending a Session Cooling down is an important aspect of your workout because it helps reduce muscle stiffness and soreness by transporting excess lactic acid out of the working muscles. In addition, a three to five minute cool down allows your heart rate to return to its normal, resting state. At the end of your workout, a Summary screen displays your average heart rate during your workout and your accumulated workout metrics.
40 Operating and Maintaining the P10 Console Three different types of metrics are captured during a workout. Controlled Metrics can be set and changed. They include: Resistance Level (AMT, EFX, bike) Speed (treadmill) Incline (treadmill) Crossramp (EFX) Current Performance Metrics describe the intensity of a workout in real time.
41 Starting a Workout Workouts Your fitness equipment includes a wide selection of workouts that are carefully designed to make sure you get the best results out of every workout. The human body is extremely efficient. If it makes the same motion regularly over many days or weeks, it learns to make that motion with less and less effort. This process, called muscle adaptation, has one drawback—the longer you stick to the same workout, the less good that workout does you.
42 Operating and Maintaining the P10 Console Weight Loss Key Pressing the Weight Loss key scrolls through the workouts that are designed to encourage weight loss and aerobic conditioning. The American College of Sports Medicine® recommends that adults get at least 30–60 minutes of moderately intense exercise five days a week. The Weight Loss workout provides a structured and time-based aerobic challenge designed to help you reverse or prevent weight gain.
43 Starting a Workout Performance Key Press the Performance key repeatedly to select a workout that conditions and tests the body’s muscular and aerobic performance. Note: On treadmills, a fitness test option is also available. A technician at the fitness facility must activate the fitness test before you can use it. After the test has been activated, you can scroll between the Track and Fitness Test workouts by pressing the Performance key repeatedly.
44 Operating and Maintaining the P10 Console Cross Training Workouts This workout delivers true training variety and muscular engagement by adjusting the resistance and incline continuously to simulate the dynamic terrain of an outdoor run. The CrossRamp setting is preprogrammed in each of these workouts, but you can change it or the resistance setting at any time.
45 Starting a Workout The treadmill ends the test prematurely if any of the following things happen: The equipment cannot detect your heartbeat. Your heart rate exceeds 85% of your maximum safe rate for 15 seconds or more. Your heart rate changes too quickly. You press the STOP switch or pull on the safety clip lanyard. Important: For best results, sit and rest for at least five minutes before you take the test.
46 Operating and Maintaining the P10 Console Variety Key Pressing the Variety key selects a random or specialized workout designed for the fitness equipment you are using. Random Variety (for both the muscles and the mind) is the key to continued success for every exercise goal. The Random workout delivers a different training profile every time you select it. The one-minute segments that appear in the workout profile maintain a set incline that you can override.
47 Starting a Workout Interval Key Interval workouts help exercisers improve strength, endurance, aerobic and anaerobic fitness. They alternate short bursts of high intensity activity with recovery periods. Pressing the Interval key selects the available interval workout. Note: On the AMT, two different interval workouts are available. Press the Interval key repeatedly to scroll between the available workouts.
48 Operating and Maintaining the P10 Console Manual Key The workout available through the Manual key motivates you by allowing you to define and track your exertion levels throughout your exercise session. Training tip: As you progress through your workout, each segment of the profile reflects the last change you made to the intensity settings. Challenge yourself by adjusting your training parameters regularly for the best results.
Chapter 5 Maintenance To keep the equipment functioning properly, perform the minor maintenance tasks in this section at the intervals suggested. Failure to maintain the equipment as described in this section could void the Precor Limited Warranty. DANGER To reduce the risk of electrical shock, always disconnect the equipment from its power source before cleaning it or performing any maintenance tasks. If the equipment uses an optional power adapter, disconnect the adapter.
50 Operating and Maintaining the P10 Console Cleaning the Console and Display The console requires little maintenance once installed. Precor recommends that you clean the console before and after each exercise session. To remove dust and dirt from the console: Wipe all exposed surfaces with a soft cloth that you have moistened with a solution of 30 parts of water to 1 part of Simple Green® (for more information, visit www.simplegreen.com). Important: Do not use any acidic cleaners.
51 Maintenance Checking and Resetting the Active Status Light (Treadmill Only) Experience Series treadmills manufactured after June 2014 include many improvements in design, function, and usability. One of those improvements is the status indicator light at the front of the treadmill hood, which gives a club owner or technician an easy way to check up on the condition of the treadmill.
52 Operating and Maintaining the P10 Console Table 9. Active status light appearances and their meanings Status light appearance Meaning Action required Steady (solid) blue The treadmill is None. operating normally and does not currently need maintenance. Pulsing blue The treadmill is due for Perform the needed scheduled maintenance, then reset the maintenance (P80 status light. console only), or the treadmill belt needs to be replaced (except for 230 V models).
Maintenance 53 To review and reset the status of the treadmill: 1. At the Welcome banner, press the Pause key, then enter the following digits on the keypad: 51765761 2. Use the up and down arrow keys to scroll through the menu names until HARDWARE VALIDATION appears. 3. In the Hardware Validation menu, use the up and down arrow keys to scroll through the menu options until ACTIVE STATUS LIGHT appears, then press OK again. 4.
54 Operating and Maintaining the P10 Console Changing the Belt (AMT Only) The AMT uses belts to provide motion. These belts eventually wear and must be replaced. When the belt stride count reaches 90 million, the message BELTS MUST BE CHANGED SOON scrolls on the Welcome screen. While this message appears, the AMT operates normally. Important: If this message displays on your AMT, please contact Precor Customer Support for assistance.
Notes Notes: 55
56 Notes: Operating and Maintaining the P10 Console
Operating and Maintaining the P10 Console Precor Incorporated 20031 142nd Avenue NE P.O.
Assembling and Maintaining the EFX® 811 Elliptical Fitness Crosstrainer™ Precor Incorporated 20031 142nd Avenue NE P.O.
Edition Information ASSEMBLING AND MAINTAINING THE EFX 811 ELLIPTICAL FITNESS CROSSTRAINER P/N 300763-201 rev E Copyright © December 2014 Precor Incorporated. All rights reserved. Specifications subject to change without notice. Trademark Note Precor, AMT, EFX, and Preva are registered trademarks of Precor Incorporated. Other names in this document may be the trademarks or registered trademarks of their respective owners.
Important Safety Instructions Important: Save these instructions for future reference. Read all instructions in the documentation provided with your exercise equipment, including all assembly guides, user guides, and owner’s manuals, before installation of this device. Note: This product is intended for commercial use. The display apparatus (hereinafter referred to as the console) is intended to be shipped with new Precor exercise equipment (hereinafter referred to as the base unit).
4 Assembling and Maintaining the EFX 811 Elliptical Fitness Crosstrainer Safety Precautions Always follow basic safety precautions when using this equipment to reduce the chance of injury, fire, or damage. Other sections in this manual provide more details of safety features. Be sure to read these sections and observe all safety notices. These precautions include the following: Read all instructions in this guide before installing and using the equipment and follow any labels on the equipment.
Important Safety Instructions 5 Never leave the equipment unattended when it is plugged in. Unplug the equipment from its power source when it is not in use, before cleaning it, and before providing authorized service. Note: The optional power adapter is considered a power source for self-powered equipment. Use the power adapter provided with the equipment. Plug the power adapter into an appropriate, grounded power outlet as marked on the equipment.
6 Assembling and Maintaining the EFX 811 Elliptical Fitness Crosstrainer SPACING—The below minimum spacing recommendations are based on a combination of the ASTM (U.S.) voluntary standards and EN (European) regulations as of October 1, 2012, for access, passage around, and emergency dismount: – Treadmills—a minimum of 0.5 m (19.7 in.) on each side of the treadmill and 2 m (78 in.) behind the machine. – Cardio equipment other than treadmills—a minimum of 0.5 m (19.7 in.
Important Safety Instructions 7 Never operate this equipment if it has a damaged cord or plug, if it is not working properly, or if it has been dropped, damaged, or exposed to water. Call for service immediately if any of these conditions exist. Maintain the equipment to keep it in good working condition, as described in the Maintenance section of the owner’s manual.
8 Assembling and Maintaining the EFX 811 Elliptical Fitness Crosstrainer Educating Users Take time to educate users about the Important Safety Instructions found in both the User Reference Manual and Product Owner’s Manual. Explain to your club or facility patrons that they should observe the following precautions: Hold onto a stationary handrail or handlebar while assuming the starting position on the equipment. Face the console at all times.
9 Important Safety Instructions Regulatory Notices for the RFID Module When equipped with a control console as described in this document, this equipment may include a radio-frequency identification (RFID) module. The RFID module has been certified to operate at temperatures between -20°C and 85°C (-4°F and 185°F). Radio Frequency Interference (RFI) The RFID module conforms to the following national standards defining acceptable limits for radio frequency interference (RFI).
10 Assembling and Maintaining the EFX 811 Elliptical Fitness Crosstrainer Industry Canada This device complies with RSS-210:2007 of the Spectrum Management & Telecommunications Radio Standards Specification. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This Class A digital apparatus complies with Canadian ICES003.
Important Safety Instructions 11 Regulatory Notices for Cardiovascular Exercise Equipment The regulatory information in this section applies to the exercise equipment and its control console. Safety Approvals for Cardiovascular Equipment Precor equipment has been tested and found to comply with the following applicable safety standards.
12 Assembling and Maintaining the EFX 811 Elliptical Fitness Crosstrainer Radio Frequency Interference (RFI) This Precor exercise equipment conforms to the following national standards defining acceptable limits for radio frequency interference (RFI). Federal Communications Commission, Part 15 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
Important Safety Instructions 13 Electrical Recommendations: All Equipment Excluding Treadmills Note: This is a recommendation only. NEC (National Electric Code) guidelines or local region electric codes must be followed. For equipment fitted with a P80 console or Personal Viewing System (PVS) screen a separate power connection is required. For a 20 amp branch circuit up to 10 screens can be connected.
14 Assembling and Maintaining the EFX 811 Elliptical Fitness Crosstrainer Obtaining Service Do not attempt to service the equipment except for maintenance tasks. If any items are missing, contact your dealer. For more information regarding customer support numbers or a list of Precor authorized service centers, visit the Precor web site at http://www.precor.com. Obtaining Updated Documentation Current Precor product documentation is available at http://www.precor.com/productmanuals.
Table of Contents Important Safety Instructions .................................................... 3 Safety Precautions ................................................................................ 4 Educating Users .................................................................................... 8 Hazardous Materials and Proper Disposal .................................... 8 Product Recycling and Disposal .......................................................
16 Assembling and Maintaining the EFX 811 Elliptical Fitness Crosstrainer Self-Powered Features.............................................................. 41 Informational Displays Prior to Shutdown .................................. 43 Symptoms of a Low Battery ............................................................ 44 Using the Optional Power Adapter ............................................... 44 The Optional Power Adapter Kit....................................................
Chapter 1 Assembling the EFX WARNING You will need the assistance of two other people to assemble this unit. DO NOT attempt assembly by yourself. Important: The instructions in the following procedures are described from the perspective of a person standing directly in front of the equipment (that is, on the opposite side of the control console from a person using the equipment).
18 Assembling and Maintaining the EFX 811 Elliptical Fitness Crosstrainer To prepare the EFX for assembly: Open the box and assemble the components in the sequence presented in this guide. Assemble and operate your equipment on a hard, level surface in the area intended for use. Use a hand truck or furniture dolly to move the EFX unit. Important: Do not grasp the unit by any of its plastic parts to move it.
19 Assembling the EFX Installation Requirements Follow these installation requirements when assembling the unit: Assemble the unit near the location where you plan to use it. Provide ample space around the unit. Open space around the unit allows for easier access. Set up the unit on a solid, flat surface. A smooth, flat surface under the unit helps keep it level. A level unit has fewer malfunctions. Open the box and assemble the components in the sequence presented in this guide.
20 Assembling and Maintaining the EFX 811 Elliptical Fitness Crosstrainer Use your fingers to properly align and thread the fasteners. This helps alleviate cross-threading. Do not fully wrench tighten fasteners until instructed to do so. Important: When wrench tightening, the head of the fastener should be flush with the product. If it is not, cross-threading may have occurred. Do not attempt to rework the assembly as more damage to the equipment will occur. Contact Customer Support.
21 Assembling the EFX Hardware Kit (not to scale) Table 1.
22 Assembling and Maintaining the EFX 811 Elliptical Fitness Crosstrainer Fasteners Quantity Pivot arm caps 2 Pivot axle covers 2 Upright support covers (packaged separately) 4
23 Assembling the EFX Assembling the EFX DANGER Do not attempt to connect electrical power until all assembly procedures are complete and the console is properly installed. Assemble the EFX in the order presented. Once you have assembled it, clean the ramp with a soft cloth dampened in a diluted solution of mild soap and water. To begin assembly: 1. Feed the cable through the right upright support. Tape the cable to the top of the upright support to secure it temporarily.
24 Assembling and Maintaining the EFX 811 Elliptical Fitness Crosstrainer 2. Attach both upright supports to the base frame using eight buttonhead screws, eight split washers, and eight washers. Finger tighten.
25 Assembling the EFX Installing the Display Console Mount 1. Ask your assistant to hold the display console mount above the upright supports while you connect the cable. Remove and discard the tape after you connect the cable. Important: Place excess cable inside the upright support. 2. Have your assistant lower the display console mount while you align the mounting brackets on the inside of the upright supports.
26 Assembling and Maintaining the EFX 811 Elliptical Fitness Crosstrainer 3. Fasten the display console mount to each upright support by threading a buttonhead screw, washer, and split washer through opposite mounting holes. Check that the base fasteners are loose before installing the display console fasteners. CAUTION: Make sure the display console mount screws are properly threaded into the inserts. Do not cross thread. The Precor Limited Warranty does not cover damage that occurs during installation.
27 Assembling the EFX Installing the Bottle Holder The bottle holder attaches to the right stationary arm handrail. To install the bottle holder: 1. Position the water bottle holder as shown and attach it to the right stationary handrail. Figure 6: Attaching the water bottle 2. Secure the holder using three Phillips-head screws and a Phillips-head screwdriver.
28 Assembling and Maintaining the EFX 811 Elliptical Fitness Crosstrainer Installing the Handlebars CAUTION: Handlebars can swing and cause injury. Have your assistant hold the handlebar and gently lower it into a vertical position when the handlebar assembly is complete. To install the moving handlebars: 1. For proper alignment, rotate the pivot arm to a horizontal position. Apply pressure to fit the protrusion on the handlebar into the handlebar bracket.
29 Assembling the EFX 2. Insert three socket head cap screws, three split washers, and three washers through each handlebar bracket. To secure the handlebars, wrench tighten the fasteners using a ¼-inch hex key.
30 Assembling and Maintaining the EFX 811 Elliptical Fitness Crosstrainer 3. Attach the handlebars to the link arms using two hex head screws, two bushings, and four washers. For ease of installation, slide the corresponding foot pedal to the top of the ramp before attaching each handlebar. Important: Install the fasteners in the order shown. The bushing slides inside the link arm. The heads of the screws remain on the ramp side of the link arm. Figure 9: Attaching the movable arms 4.
31 Assembling the EFX Attaching the Caps and Upright Support Cover You will need the arm caps and foot covers to complete the following tasks. To attach the caps and upright support covers: 1. Align the cut-out inside the link arm cap with the link arm mounting hole. Apply pressure to the cap until it snaps into place.
32 Assembling and Maintaining the EFX 811 Elliptical Fitness Crosstrainer 2. Attach the pivot arm caps. Figure 11: Attaching the upright support covers 3. Place one inner and one outer upright support cover around an upright support. Align each pair so the arrows on the covers point toward the front of the unit. Apply pressure to engage the inner cover protrusions with the outer cover screw holes. 4. Slide the covers down into the base mount.
33 Assembling the EFX Making Sure the Unit is Stable Make sure the unit is level before allowing anyone to use it. CAUTION: To eliminate movement, make sure the adjustable feet are in contact with the floor. To level the unit: 1. Gently rock the unit. If there is any movement, ask your assistant to tip the unit to one side while you locate the adjustable feet. 2. Correct the height of each adjustable foot as follows.
34 Assembling and Maintaining the EFX 811 Elliptical Fitness Crosstrainer Verifying that the Heart Rate Display is Operational To verify that the heart rate display is operational: 1. Hold on to a stationary handrail and step on the foot pedals. 2. When you are comfortably situated, begin pedaling. A pedaling speed above 40 strides per minute must be maintained for several seconds. 3. Grasp both touch-sensitive handrail grips on the stationary handrails. 4. Look at the HEART RATE display.
Chapter 2 Installing the Console To make installation easier, all Precor Experience Series consoles use the same mounting hardware and connector locations whenever possible. The installation sequence for any of them is as follows: Threading the console cable assembly Connecting cables Completing the installation (tightening the mounting screws and attaching the back cover) The following sections describe how to perform these tasks.
36 Assembling and Maintaining the EFX 811 Elliptical Fitness Crosstrainer Threading the Console Cable Assembly Earlier in the installation, you threaded the necessary cables through the frame of the base unit and out the passthrough opening in the console mount. As you line up the back plate on the console with the console mount, you must make sure that the console cable assembly passes correctly through the openings in both components.
Installing the Console 37 Connecting Cables Important: Pass all cables through the semicircular opening just above the console mount, as shown in the following figure. Do not attempt to route any cables through other openings or through the steel channel above the mount.
38 Assembling and Maintaining the EFX 811 Elliptical Fitness Crosstrainer Figure 14: Cable connections, P30 and P10 consoles Table 2.
Installing the Console 39 Completing the Console Installation Before you complete the final installation steps, double-check the connections you have made. Make sure that all cables are fully and securely connected, and that any unneeded cables are tied back properly. To complete the installation: 1. Feed extra cable back into the neck tube. 2.
40 Assembling and Maintaining the EFX 811 Elliptical Fitness Crosstrainer 4. Line up the two small tabs at the bottom of the console’s back cover with the slots at the bottom of the console case. Insert the tabs into the slots. 5. Insert the two #8–32 x ¹ ₂-inch Phillips-head screws that you removed earlier into the holes at the top edge of the console’s back cover. Tighten the screws fully. Important: Use caution not to pinch the cables between the back cover and PVS mounting screw heads. 6.
Chapter 3 Self-Powered Features Important: This chapter of the manual describes Precor fitness equipment that can operate without being connected to AC power. This includes units equipped with P30 or P10 consoles. However, P80 consoles must be connected to AC power through their power supplies to operate. For this reason, this chapter does not apply to units equipped with P80 consoles. On self-powered equipment, the system initializes and displays the Welcome screen when a user starts exercising.
42 Assembling and Maintaining the EFX 811 Elliptical Fitness Crosstrainer Informational displays appear when the battery is low or when the rate of motion drops below the minimum requirements. The display explains what to do to retain power. If the messages are ignored, the equipment begins shutdown procedures to maintain the charge of the battery. Refer to Informational Displays Prior to Shutdown. An optional power adapter can be purchased and provides sustained power to the equipment.
Self-Powered Features 43 Informational Displays Prior to Shutdown The equipment saves its battery charge by moving into a shutdown mode. If the user does not maintain the minimum rate of motion, a 30-second shutdown process begins. In this mode, the console displays a countdown indicator and ignores all key presses. If no movement is detected or the rate of motion remains below the minimum, the indicator changes as the countdown continues.
44 Assembling and Maintaining the EFX 811 Elliptical Fitness Crosstrainer Symptoms of a Low Battery If no one has used the equipment for an extended period of time, the battery may need recharging.
Self-Powered Features 45 The Optional Power Adapter Kit If you purchase the optional power adapter, you must also purchase the internal cable kit. The kit supplies the cable, bracket, and fasteners that connect the power adapter to the lower electronics board. CAUTION: The internal cable kit must be installed by authorized service personnel. Do not attempt installation on your own as you could void the Precor Limited Warranty. For more information, refer to Obtaining Service.
46 Assembling and Maintaining the EFX 811 Elliptical Fitness Crosstrainer Replacing the Battery The equipment’s battery is built to last for a long time. However, if you feel that the battery may need replacing, check with an authorized service technician. Refer to Obtaining Service. CAUTION: The battery stored inside the equipment contains hazardous materials and must be disposed of according to Hazardous Waste Regulations. Refer to Hazardous Materials and Proper Disposal.
Chapter 4 Maintenance To keep the equipment functioning properly, perform the minor maintenance tasks at the intervals shown in this section. Failure to maintain the equipment as described in this section could void the Precor Limited Warranty. DANGER To reduce the risk of electrical shock, always disconnect the equipment from its power source before cleaning it or performing any maintenance tasks. If the equipment is self-powered but also uses the optional power adapter, disconnect the adapter.
48 Assembling and Maintaining the EFX 811 Elliptical Fitness Crosstrainer Daily Cleaning Precor recommends that you clean the equipment before and after each exercise session. To remove dust and dirt from the equipment, wipe all exposed surfaces with a soft cloth that you have moistened with one of the following cleaners: A solution of 30 parts of water to 1 part of Simple Green® (for more information, visit www.simplegreen.
49 Maintenance Daily Inspection At least once every day, examine the equipment for the following problems: Slipping belts Loose fasteners Unusual noises Worn or frayed power cords Any other indication that the equipment may be in need of service Important: If you determine that the equipment needs service, disconnect all power connections (television, Ethernet, and power) and move the equipment away from the exercise area.
50 Assembling and Maintaining the EFX 811 Elliptical Fitness Crosstrainer Weekly Maintenance Perform the following maintenance tasks every week: 1. Disconnect the external power supply. 2. Clean the ramps and wheels with water or an approved cleaner. 3. Inspect the power cord to verify that it is not pinched under the equipment or between any two moving parts. 4. Clean the floor under the equipment using a vacuum cleaner or a damp mop. 5. When the floor is completely dry, reconnect the power. 6.
51 Maintenance Monthly Maintenance DANGER USE EXTREME CAUTION when the rear cover of any EFX is removed. Serious injury could result if fingers are pinched between the flywheel spokes, cranks, movable arms, and the drive weldment. Securing the movable arm to the crank with a clamp is recommended. Be aware of other people within your work area who might cause the arm to move. Perform the following maintenance tasks every month: 1. 2. 3. 4. 5. 6. 7. 8. 9.
52 Assembling and Maintaining the EFX 811 Elliptical Fitness Crosstrainer Storing the Chest Strap If you purchased the optional heart rate chest strap, store it in a place where it remains free of dust and dirt (for example, in a closet or drawer). Be sure to protect the chest strap from extremes in temperature. Do not store it in a place that may be exposed to temperatures below 32° F (0° C). To clean the chest strap, use a sponge or soft cloth dampened in mild soap and water.
Assembling and Maintaining the EFX® 811 Elliptical Fitness Crosstrainer™ Precor Incorporated 20031 142nd Avenue NE P.O.
