Treadmill Integrated LCD Screen Option Cardio Theater Integrated Bracket Assembly Instructions
Cardio Theater Integrated Bracket Assembly Instructions Table of Contents 1 Before You Begin ............................................................................................. 4 Obtaining Service ........................................................................................................................ Unpacking the Equipment ........................................................................................................... Important Safety Instructions .................
1 Before You Begin Thank you for adding the Precor Cardio Theater Integrated LCD Screen Option to your treadmill. This option will add a new dimension to your workout. For proper installation, please read this guide thoroughly and follow the assembly instructions. Obtaining Service For information about product operation or service, see the Precor web site at www.precor.com.
Cardio Theater Integrated Bracket Assembly Instructions 2 Preparations Important: To attach the Cardio Theater Integrated Bracket, ask another adult for help. Do not attempt the assembly by yourself. Installation Requirements Assembly Tips Review these installation requirements before assembly: • Read all the notes on each page before completing that step. Remember to read and follow the instructions in this guide.
Cardio Theater Integrated Bracket Assembly Instructions 3 1 Bracket assembly Install the Bracket Assembly Bracket cover Pivot tube Important: Assemble the fasteners throughout these instructions as detailed in each step. When in doubt, use the illustrations for help. Do not fully tighten fasteners until instructed to do so. 1. Remove the bracket cover. Loosen the bolts on the pivot tube using a ⁷⁄₃₂-inch hex key. Pull the bracket cover away from the assembly. Set it aside. 2.
Cardio Theater Integrated Bracket Assembly Instructions 3. Continue to feed the coaxial/power cable and its two connectors through the left bracket arm. Feed the coaxial/power cable and its two connectors back through the hole at the base of the center tube and down the left arm of the bracket assembly. Pull the cables from the side slot. Continue pulling until no cable (except the coiled controller cable) protrude from the hole at the base of the center tube.
Cardio Theater Integrated Bracket Assembly Instructions 4. Attach the power extension cable to the power connector. 4 6 5. Set the bracket assembly aside. 6. Remove the fasteners that secure the display console to the treadmill. Use a hex key to remove the four screws and washers that secure the display console to the upright supports on the treadmill. Keep the washers on the screws and set them aside. Display console Power connector Important: Ask someone for help before attempting the next step.
Cardio Theater Integrated Bracket Assembly Instructions 9. Align the mounting holes. Ask your assistant to slide the bracket assembly to the inside of the upright supports and align the mounting holes. Important: Continue feeding the remaining cable so that no cable protrudes or gets pinched while mounting the bracket. 9 Display console Bracket assembly 10. Replace the fasteners. Use a hex key to replace the four screws and washers removed in step 6.
Cardio Theater Integrated Bracket Assembly Instructions 4 2 Metal mounting bracket 3 Attach the LCD Screen Plastic cover Important: The screen spacer is used only for the Cardio Theater PVS4/5/15 LCD Screen. 1. To protect the LCD Screen for the next few steps, place it screen side down on a clean work surface. Important: Use proper materials to protect the LCD Screen while you remove the plastic cover and metal mounting bracket from the back of the LCD Screen. LCD screen 2. Remove the plastic cover.
Cardio Theater Integrated Bracket Assembly Instructions 6. Fully tighten the bottom two screws. Use a Phillips-head screwdriver to fully tighten the bottom two screws. Leave the top two screws finger tight. 7 6 7. Connect the coaxial/power cable connectors to the LCD Screen. Attach the connectors—coaxial and power—to the back of the LCD screen. 8. Feed the DVD connector back into the pivot tube compartment so it is not hanging out. The DVD Option is not available for the treadmill.
Cardio Theater Integrated Bracket Assembly Instructions 5 1 Top of the bracket cover Bracket cover Reinstall the Bracket Cover 1. Prepare the fasteners for reinstalling the bracket cover. Push the washers and bearings toward the bolt heads so there is room for the bracket cover to slide in flush against the pivot tube. Important: Keep the bracket cover flanges flush with the pivot tube. The washers and bearings need to remain on the outside of the bracket flanges. 2. Replace the bracket cover.
Cardio Theater Integrated Bracket Assembly Instructions 6 Controller Bracket bar Connect the Controller and the Cables Rubber adapter mounts Note: Retrieve the rubber adapter mounts from the bracket assembly package. Retrieve the controller from the LCD Screen package. Controller cable 1. Connect the controller cable to the controller. A definite click is heard when the connector snaps into place inside its receptacle. 2. Place the rubber adapter mounts around the center of the bracket bar.
Precor Incorporated 20031 142nd Avenue NE P.O. Box 7202 Woodinville, WA USA 98072-4002 Precor and Cardio-Theater are registered trademarks of Precor Incorporated. Specifications subject to change without notice. Copyright 2005 Precor Incorporated. Precor web site: www.precor.com NOTICE: Precor is widely recognized for its innovative, award winning designs of exercise equipment. Precor aggressively seeks U.S.
