® EFX Integrated LCD Screen Option Cardio Theater Integrated Bracket Assembly Instructions
Cardio Theater Integrated Bracket Assembly Instructions Table of Contents Table of Contents 1 Before You Begin ............................................................................................. 4 Obtaining Service ........................................................................................................................ Unpacking the Equipment ...........................................................................................................
1 Before You Begin Thank you for adding the Precor Cardio Theater Integrated LCD Screen Option to your EFX®. This option will add a new dimension to your workout. For proper installation, please read this guide thoroughly and follow the assembly instructions. Obtaining Service For information about product operation or service, refer to the Precor web site at www.precor.com.
Cardio Theater Integrated Bracket Assembly Instructions 2 Preparations Important: To attach the Cardio Theater Integrated Bracket, ask another adult for help. Do not attempt the assembly by yourself. Installation Requirements Assembly Tips Review these installation requirements before assembly: • Read all the notes on each page before completing that step. Remember to read and follow the instructions in this guide.
Cardio Theater Integrated Bracket Assembly Instructions 3 Preparing the Unit The illustration shows how the Cardio Theater Integrated Bracket will look after you install it on the EFX. EFX546i EFX556i This section contains preparation instructions for both the EFX546i and the EFX556i.
Cardio Theater Integrated Bracket Assembly Instructions Preparing the EFX546i 1 3 Rubber grommet Handrail clamp 1. Loosen the two screws on the handrail clamp using a ⁵⁄₃₂-inch hex key. Important: Leave the handrails in the clamp. Do not remove the handrail clamp screws! Handrail Front cover 2. Remove the front cover. Loosen and remove the two screws securing the front cover. Set the front cover and fasteners aside. 3. Move rubber grommet.
Cardio Theater Integrated Bracket Assembly Instructions 5. Remove the four fasteners securing the upright support. Use a ¼-inch hex and ½-inch box end wrench to remove the fasteners. Keep the fasteners together and within easy reach. Important: Ask someone for help before completing the next step. 5 6 Assistant must hold onto the display console to keep it from sliding. Rubber grommet 6. Separate the display console from its bracket.
Cardio Theater Integrated Bracket Assembly Instructions 8. Attach the power extension cable to the power connector on the coaxial/power cable. 8 Locate the coaxial/power cable provided with the LCD Screen. One end of the coaxial/power cable has three connectors; the other end has two connectors. Attach the power extension cable to the power connector on the end with the two connectors (coaxial and power). Handrail Power connector Display console bracket 9.
Cardio Theater Integrated Bracket Assembly Instructions 11. Secure the display console. Replace two of the screws at the base of the console bracket. Do not fully tighten the screws. Leave space between the screw head and the display console bracket. The bracket assembly slides in between the two. Note: Once the display is secure, your assistant can let go of the display. Display console 12. Pry the rubber end cap off the base. Use a flat head screwdriver. Display console bracket 13.
Cardio Theater Integrated Bracket Assembly Instructions 14. Continue to feed the cable with its connectors through the lower support. Start with the coaxial and power extension connectors. Feed them into the lower support. Continue to slide the cable and its connectors so no excess remains at the gap between the upper and lower supports. Ask your assistant to release pressure on the upper support and realign the mounting holes between the upper and lower supports.
Cardio Theater Integrated Bracket Assembly Instructions 19. Secure the upright support by replacing the four fasteners set aside in step 5. 20. Retighten the two handrail clamp screws. Important: Look underneath the handrail clamp at the gap between the handrails. The area between the ends of the handrails should be no larger than a ¼-inch gap. If necessary, push the handrails toward each other before tightening the screws. 21. Replace the back cover and rubber grommet.
Cardio Theater Integrated Bracket Assembly Instructions 22. Reinstall the front cover and secure it with the two screws removed in step 2. Before tightening the front cover, be sure to fit the lip of the front cover into the tabs along the inside surface of the grommet. 22 Upright support To complete the installation, refer to the instructions on page 19.
Cardio Theater Integrated Bracket Assembly Instructions Preparing the EFX556i 1 3 Rubber grommet 1. Pry the rubber end cap off the base using a flat head screwdriver. Set the end cap aside. 2. Remove the front cover. Loosen and remove the two screws securing the front cover. Set the front cover and fasteners aside. Front cover 3. Move rubber grommet. Slide the rubber grommet along the upright support toward the display. End cap 4. Remove the back cover. Loosen the two screws securing the back cover.
Cardio Theater Integrated Bracket Assembly Instructions Important: Ask someone for help before completing the next step. 5. Remove the four fasteners securing the upright support. Ask your assistant to hold the upper support while you use a ¼-inch hex and ½-inch box end wrench to remove the four fasteners that secure the upright support. Keep the fasteners together and within easy reach. Important: A data cable runs the length of the upright support.
Cardio Theater Integrated Bracket Assembly Instructions 10. Attach the power extension cable to the power connector on the coaxial/power cable. Locate the coaxial/power cable provided with the LCD Screen. One end of the coaxial/power cable has three connectors; the other end has two connectors. Attach the power extension cable to the power connector on the end with the two connectors (coaxial and power). Coaxial connector Power connector 11.
Cardio Theater Integrated Bracket Assembly Instructions 13. Secure the display console. Replace two of the screws at the base of the display console bracket. Do not fully tighten the screws! Leave space between the screw heads and the display console bracket. The bracket assembly slides in between the two. 13 Display console 14. Reconnect the data cable. Ask your assistant to hold the upper support above the lower support while you reconnect the data cable.
Cardio Theater Integrated Bracket Assembly Instructions 16. Pull the cable and its two connectors out of the lower support and base tube. Note: Remember to leave about 3 feet (1 meter) of cable hanging out of the hole in the display console bracket. Read CAUTION above Step 18. 16 Lower support 18 17. Secure the upright support by replacing the four fasteners set aside in step 5.
Cardio Theater Integrated Bracket Assembly Instructions 21. Replace the back cover and rubber grommet. Replace the back cover onto the upright support. Fit the lip of the back cover into the tabs along the inside surface of the grommet. Apply pressure to the top of the back cover while you tighten the screws. 21 Rubber grommet Back cover 22. Reinstall the front cover and secure it with the two screws removed in step 2.
Cardio Theater Integrated Bracket Assembly Instructions 4 Install the Bracket Assembly Bracket assembly 1. Remove the bracket cover. Loosen the bolts on the pivot tube using a ⁷⁄₃₂-inch hex key. Pull the bracket cover away from the assembly. Set it aside. 2. Feed the coaxial/power cable with its three connectors through the bracket assembly.
Cardio Theater Integrated Bracket Assembly Instructions 3. Fit the bracket assembly on to the display console bracket. Ask your assistant to lift the bracket assembly and position it along the back of the display console bracket. Make sure the bracket assembly slides into place so that the cutouts at the base of the flanges fit around the bottom two screws. 3 EFX556i Bracket flange 4. Secure the bracket assembly to the display console bracket.
Cardio Theater Integrated Bracket Assembly Instructions 5 Metal mounting bracket 2 3 Attach the LCD Screen Plastic cover Important: The screen spacer is used only for the Cardio Theater PVS4/5/15 LCD Screen. 1. To protect the LCD Screen for the next few steps, place it screen side down on a clean work surface. Important: Use proper materials to protect the LCD Screen while you remove the plastic cover and metal mounting bracket from the backside of the LCD Screen. LCD screen 2.
Cardio Theater Integrated Bracket Assembly Instructions 6. Fully tighten the bottom two screws. Use a Phillips-head screwdriver to fully tighten the bottom two screws. Leave the top two screws finger tight. 6 7 7. Connect the coaxial/power cable connectors to the LCD Screen. Attach the connectors—coaxial, power, and DVD—to the back of the LCD Screen. Note: If you do not have a DVD option, you can feed the DVD cable back into the pivot tube compartment so it is not hanging out. Power connector 8.
Cardio Theater Integrated Bracket Assembly Instructions 6 1 3. Tighten the two top screws on the back of the LCD Screen. Use a Phillips-head screwdriver to fully tighten the top two screws on the back of the LCD Screen. Access holes have been drilled through the bracket cover. Top of bracket cover Bracket cover Reinstall the Bracket Cover 1. Prepare the fasteners for reinstalling the bracket cover.
Cardio Theater Integrated Bracket Assembly Instructions 7 Controller Bracket bar Connect the Controller and the Cables Rubber adapter mounts Note: Retrieve the rubber adapter mounts from the bracket assembly package. Retrieve the controller from the LCD Screen package. Controller cable 1. Connect the controller cable to the controller. A definite click is heard when the connector snaps into place inside its receptacle. 2. Place the rubber adapter mounts around the center of the bracket bar.
Precor Incorporated 20031 142nd Avenue NE P.O. Box 7202 Woodinville, WA USA 98072-4002 Precor and Cardio-Theater are registered trademarks of Precor Incorporated. Specifications subject to change without notice. Copyright 2005 Precor Incorporated. Precor web site: www.precor.com NOTICE: Precor is widely recognized for its innovative, award winning designs of exercise equipment. Precor aggressively seeks U.S.
