Product Manual

4
Assembly Instructions
Tools Needed For Cart Assembly
(2) 7/16” Wrenches
(2) 1/2” Wrenches
(1) 9/16” Wrench
(1) Pair Pliers
(1) Large Standard or Flat Screwdriver
Remove from Carton
Remove all parts and hardware packages from the
carton. Lay out all parts and hardware and identify
them using the illustrations pages 2 and 3.
1 Attach Axle Support to the bottom of the Body.
Use 3/8” x 3/4” Truss Head Bolts, 3/8” Lock Wash-
ers, and secure with 3/8” Hex Head Nuts. See Fig-
ure 1.
2. Attach Pedestal to front of Body. Use 3/8” x 3”
Hex Head Bolts and 3/8” flat washer from outside.
On the inside, use 3/8” Lock Washers and secure
with 3/8” Hex Head Nuts. See Figure 2.
3. Move Body to flat position with Axle Supports and
Pedestal face up. Slide Axle halfway through Axle
Support. Place Tow Bar in between both Axle Sup-
ports, locking latch to Pedestal then slide the Axle
though the holes in the Tow Bar then all the way
through the next Axle Support. (4) 1” Flat Washers
are available to fit in between the Tow Bar and Axle
Support to reduce movement of the Tow Bar. See
Figure 3.
Figure 1
3/8” Flat
Washer
3/8” Truss
Head Bolt
3/8”
Lock
Washer
3/8”
Hex
Head
Nut
Figure 2
3/8” Flat
Washer
3/8” Lock
Washer and
3/8” Nut
Axle
Tow Bar
Pedestal
1” Flat
Washer
Figure 3
5
4. Slide Axle Spacer onto Axle so it is up against the
Axle Support. Place once 1” Flat Washer onto axle
followed by one tire. Place one 3/4” Flat Washer
up against tire and thread onto the Axle the 3/4”-
10 Slotted Hex Nut. Secure Wheel in place by in-
serting Cotter Pin through hole in the end of Axle
and spreading the legs of the Cotter Pin outward.
Repeat the Wheel attachment step for the other
wheel. See Figure 4.
5. Turn Cart to an upright position. Attach Tow Bar
to hitch of tractor by pulling up on the Clevis Han-
dle, and inserting the Tractor Hitch into the Clevis
Spring Casing and the bottom of the Tow Bar. Re-
lease Clevis Handle when holes are aligned.
See Figure 5.
Figure 5
Hitch goes
here
Clevis
Handle
Figure 4
3/4” Flat Washer
3/4” -10 Slotted
Hex Nut
Cotter Pin
Axle Spacer
1” Flat Washer
Axle
Operation
• TO DUMP - Pull Latch toward lawn tractor and
Cart Body will tilt back to dump position.
• TO RETURN TO PULLING POSITION - Push
down on front edge of Cart Body until Latch
engages and secures to Tow Bar.
• Tractor speed should be governed by weight of
load. The heavier the load, the slower the
speed for safe operation.
Maintenance Instructions
• Keeping the cart clean and dry will prolong the
unit’s life.
• Grease Wheels at regular intervals, at least
once every six months, more frequently if used
regularly.
• Should rust develop, sand lightly then paint ar-
ea with enamel paint.
• Check tire pressure at regular intervals. Proper
inflation will prolong the life of tires (see side of
tire for inflation amount.
Parts and Support
Please do not return this product to the
store prior to contacting Precision.
At Precision Products, Inc. our goal is to deliver
quality, value and outstanding service. If for any
reason our product does not meet your expecta-
tions, please contact us and we will take care of any
problem you may have with this unit.
When ordering replacement parts please have the
model number, part description, part number, in-
spector number and date on carton, available so
that we can best serve you.
1 [phone]
www.precisionprodinc.com
Precision Products Inc.
316 Limit St.
Lincoln IL 62656
STOP