Instructions / Assembly

2
Rules for Safe Operation
The following safety precautions are suggested.
This Trash Hog is designed, engineered and
tested to offer reasonably safe and effective
service, provided that it is operated in strict
accordance with these instructions. Failure to
do so may result in personal injury. Always
observe the rules of safe operation. Please read
and retain this manual.
1. Be sure that all nuts and bolts are installed
so that the heads of the bolts are facing the
outside and the nuts are put on the inside
facing the center of the unit. Except for the
nuts and bolts used to secure the axle.
2. Keep all nuts, bolts and screws tight to be
sure equipment is in safe working condition.
Tools
(1) Flat Screwdriver (Large)
(1) Adjustable Wrench
(1) Hammer
Assembly Instructions
(Leave all nuts and bolts loosely fastened until
all hardware is in place)
1. Mount Frame Bracket to Handle by inserting
a 1/4” x 1-3/4” Bolt through the Handle, place a
1/2” Rubber Spacer onto the Bolt, followed by a
Frame Bracket and secure with a 1/4” Hex
Head Nut. Repeat process on the other side.
Do not tighten until Upper Frames are
installed and adjusted to container size.
See Figure 1.
2. Mount the Lower Frames, to the Frame
Bracket by inserting 1/4” x 1/2” Bolts through
the Lower Frames. Then insert through the
holes in the Frame Bracket and secure with
1/4” Hex Head Nut. Repeat the process on the
other side. See Figure 2.
Frame
Bracket
1/4” Hex
Head Nut
1/4” x 1/2”
Bolt
Figure 1
1/2” Rubber
Spacer
1/4” Hex
Head Nut
Frame
Bracket
Handle
1/4” x 1-
3/4” Bolt
Figure 2
Lower
Frame
3
Ref. Qty. Description Part No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
2
2
2
1
2
1
6
2
2
2
2
2
2
2
2
2
8
Wheel
Lower Frame
Upper Frame
Handle
Frame Bracket
Axle
1/4” x 1-1/4” Hex Head Bolt
1/4” Spring Nut
1/2” Flat Washer
1/2” x 3” Spacer
Axle Bracket
Hub Cap
Tube Cap
1/2” Rubber Spacer (Thin)
1/4” x 1/2” Truss Head Bolt
1/4” x 1-3/4” Bolt
1/4” Hex Head Nut
1916DJ
1920B
1921B
1922B
1923
1585
1046
1051
1506
1928
1410
1040
1082
1944
1175
1065
1270
3. Insert a 1/4” x 1-1/4” Bolt into the Handle
then through Lower Frame and secure with a
1/4” Spring Nut. Repeat the process on the
other side. See Figure 3.
4. Mount the Axle loosely to the bottom of the
Lower Frame with Axle Brackets. Insert the 1-1/4”
Bolts up through the Lower Frame, then through
the Axle Brackets, and secure with a 1/4” Hex Head
Nut. Place one 1/2” Flat Washer on each side of the
Axle, followed by a 1/2” x 3” Spacer. Place a Wheel
on each side of the Axle, secure by tapping a Hub
Cap onto each side of the Axle. Spread the Lower
Frames so that the Axle Brackets are snug against
Wheel Assembly, now tighten these nuts and bolts
only. Place one Tube Cap onto each end of the Han-
dle. See Figure 4.
Lower
Frames
1/4” x 1-
1/4” Bolt
1/4” Spring
Nut
Handle
Figure 3
Figure 4
5. Insert Upper Frames into Frame Brackets. Place
waste containers in the TRASH HOG and adjust the
Upper Frames to fit containers. Now tighten all
loose nuts and bolts. See Figure 5.
Frame Bracket
Upper Frame
Figure 5
Lower
Frame
1/4” x 1-1/4”
Bolt
Axle
Bracket
Handle
Tube Cap
Hub
Cap
Wheel
1/2” Flat
Washer
Axle
1/2” x 3”
Spacer