Warranty

ManualsBrandsPPG Prefinished ManualsBuilding materialsPPG Premium Prefinished™ 1-1/4 x 12 x 12' Hunt Club Red Smooth Fiber Cement Trim Board 30-yr Paint Warranty

Duracolor™ FC Exterior Finish 30 Year Limited Warranty

30/15

30 YEAR LIMITED WARRANTY FOR PRE-FINISHED FACTORY APPLICATION

Limited Warranty: When PPG Machine Applied Coatings Duracolor FC Exterior Finish (the “Product”) is applied by a PPG Authorized

Machine Applicator (the “Machine Applicator”) to specified sides of clean, dry properly primed and approved substrate where the total combined

dry film thickness of the Product is at least 3.8*mils and in accordance with published surface preparation and application procedures in PPG

Technical Data Bulletins, PPG Architectural Finishes, Inc. (“PPG”) warrants to the Machine Applicator for a period of THIRTY (30) years from

the date of installation of the siding (the “Warranty Period”), that under normal exposure conditions and subject to the terms, conditions,

exclusions and limitations of this Limited Warranty, this Product is:

-PEEL AND FLAKE RESISTANT: Finish coat will not peel or flake from a properly prepared substrate.

-WASHABLE: Dirt can be removed without damaging the finish.

-RESISTANT TO CHALK WASHDOWN: Will not cause chalk stains on brick or other surfaces below coating.

* 3.8 DFT requires application of the Product where the dry film thickness is at least 3.8 mils to the five exposed sides of factory primed

FIBER CEMENT siding and trim. Coating thickness must be measured by a suitable method and documented in the Machine Applicator’s

production or quality control records.

PPG Duracolor FC Exterior Finish Limited Warranty Conditions

IN THE EVENT THE PRODUCT FAILS TO CONFORM TO THIS LIMITED WARRANTY, PPG, AS ITS SOLE LIABILITY AND IN LIEU

OF ANY DIRECT OR INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, WILL, AT THE MACHINE

APPLICATOR’S OPTION, FURNISH SUFFICIENT REPLACEMENT COATINGS TO REPAIR THE SIDING INVOLVED OR REFUND

THE PURCHASE PRICE OF THE ORIGINALLY INSTALLED COATING DETERMINED BY PPG TO BE IN NON-CONFORMITY.

LABOR OR COSTS OF LABOR FOR THE REMOVAL OF ANY PRODUCT OR THE APPLICATION OF ANY REPLACEMENT

COATING IS SPECIFICALLY OUTLINED UNDER “LABOR AND COSTS OF LABOR” BELOW. LABOR OR COSTS OF LABOR AND

ANY OTHER EXPENSES, SUCH AS FOR ACCESSORIES (building paper fasteners, caulking, etc.) THAN AS SPECIFICALLY OUTLINED

BELOW ARE SPECIFICALLY EXCLUDED. PPG’s obligations under this Limited Warranty shall in no event exceed the purchase price of the

original Product associated with the specific job which gives rise to a claim under this Limited Warranty. Any replacement product provided in

response to a warranty claim shall be warranted only for the balance of the Warranty Period under this Limited Warranty. As consideration for

any refund or material replacement pursuant to this Limited Warranty any such refund or material replacement shall constitute a full settlement

and release of all claims of the Machine Applicator for damages or other relief, and shall be a complete bar to any litigation filed subsequently to

the Machine Applicator’s acceptance of such refund or material replacement.

Labor and Costs of Labor

If, during the Warranty Period, all or a portion of the Product is determined by PPG in its sole discretion to have a warrantable defect (such

defective portion of the Product, the “affected product”), PPG shall:

a) Prior to installation, replace the affected product;

b) During the first seven (7) years following installation, at the sole discretion of PPG, reimburse the Machine Applicator for the paint and

reasonable labor costs required to repair the affected product;

c) During the 8

year following installation through the end of the 15

year following installation, reimburse the Machine Applicator for the

paint and reasonable labor costs required to repair the affected product as follows: commencing on the first day of the 8

year following

installation and continuing on the first day of each year thereafter, PPG’s obligation to reimburse the Machine Applicator for reasonable labor

costs under the Limited Warranty will be reduced by 11.11% each year such that after the 15

year, PPG will have no further obligation to

reimburse the Machine Applicator for reasonable labor costs.

d) During the 16

year following installation through the end of the 30

year following installation, reimburse the Machine Applicator for the

paint required to repair the affected product. During such period, PPG will have no obligation to reimburse any labor costs or expenses incurred

to repair the affected product.

Summary of content (2 pages)

PAGE 1
Duracolor™ FC Exterior Finish 30 Year Limited Warranty 30 YEAR LIMITED WARRANTY FOR PRE-FINISHED FACTORY APPLICATION Limited Warranty: When PPG Machine Applied Coatings Duracolor FC Exterior Finish (the “ Product” ) is applied by a PPG Authorized Machine Applicator (the “Machine Applicator”) to specified sides of clean, dry properly primed and approved substrate where the total combined dry film thickness of the Product is at least 3.
PAGE 2
Duracolor™ FC Exterior Finish 30 Year Limited Warranty Only those affected areas which are validated by PPG to have a warrantable defect will be covered under this Limited Warranty. PPG’s obligations under this Limited Warranty, including reimbursement for paint and reasonable labor costs shall in no event exceed the purchase price of the original Product associated with the specific job which gives rise to a claim under this Limited Warranty.