User manual

UP Mini
3D Printer User Manual
the value of how many grams of material you have on the current spool. If i
quantity should be set to 700 grams.
with is ABS or PLA.
TIP:
An empty spool weighs about 280 grams so, if you are installing a partially used spool,
weigh it, and subtract
280 grams from the weight. This gives you the value to enter into the mat
rial text box.
Status: Displays
the temperature of
plays what it’s target temperature is
Stop All: Stops
heating and all the movement of the printer. Once
model being printed is
cancelled
stopped.
After you use the “Stop All” opti
Pause Print:
This button allows you to pause a print in mid
print job where it left off. This is very useful if you, for example, want to change the material co
our mid-prin
t. Another popular use for pausing a job mid
into printed cavities and then printed over to lock the fastener into place.
truder and platform heating during the pause, it’s not recommended
time.
Nozzle & Platform: The f
ive buttons
and the platform. The nozzle moves to the left and right; the platform moves forward and bac
ward.
The “To” button controls
the height of the platform
procedure described in 3.3.2.
The “Bottom” button returns
the platform to the lowest position.
Set Nozzle Height:
Takes whatever value you have in the “To” box and transfers it t
box of the setup screen.
3D Printer User Manual
the value of how many grams of material you have on the current spool. If i
t is a new spool, the
quantity should be set to 700 grams.
You can also specify whether the material you are printing
An empty spool weighs about 280 grams so, if you are installing a partially used spool,
280 grams from the weight. This gives you the value to enter into the mat
the temperature of
the nozzle. Note: The platform
temperature reading only di
plays what it’s target temperature is
. It does not display the current
actual temperature.
heating and all the movement of the printer. Once
you
click this button, the
cancelled
.
You CANNOT resume a print job once the printer has been
After you use the “Stop All” opti
on, you will need to re-Initialise
the printer.
This button allows you to pause a print in mid
-progress, yo
u can then resume the
print job where it left off. This is very useful if you, for example, want to change the material co
t. Another popular use for pausing a job mid
-
print is to allow fasteners to be inserted
into printed cavities and then printed over to lock the fastener into place.
Note:
This keeps the e
truder and platform heating during the pause, it’s not recommended
to pause for long periods of
ive buttons
(FL, FR, Center, NL, NR) control the
position of the nozzle
and the platform. The nozzle moves to the left and right; the platform moves forward and bac
the height of the platform
, and is
used in the nozzle height calibration
the platform to the lowest position.
Takes whatever value you have in the “To” box and transfers it t
31
t is a new spool, the
You can also specify whether the material you are printing
An empty spool weighs about 280 grams so, if you are installing a partially used spool,
280 grams from the weight. This gives you the value to enter into the mat
e-
temperature reading only di
s-
actual temperature.
click this button, the
current
You CANNOT resume a print job once the printer has been
the printer.
u can then resume the
print job where it left off. This is very useful if you, for example, want to change the material co
l-
print is to allow fasteners to be inserted
This keeps the e
x-
to pause for long periods of
position of the nozzle
and the platform. The nozzle moves to the left and right; the platform moves forward and bac
k-
used in the nozzle height calibration
Takes whatever value you have in the “To” box and transfers it t
o the Nozzle