OPERATOR’S MANUAL Multiwash 14 PFMW14 WARNING: OPERATOR MUST READ AND UNDERSTAND THIS MANUAL COMPLETELY BEFORE OPERATING THIS EQUIPMENT.
CONTENTS Page Product information 3 Important safety advice 3 Guidelines for the operator 3 Working principle 3 Know your machine 4 Preparing for use 5 Assembly 5 Controls 6 Operating machine 7 Care of the machine 8 Maintenance 8 Brush selection guide 9 Brush identification 9 Accessories 10 After sales service 10 Electrical dia
IMPORTANT! READ THESE INSTRUCTIONS AND RETAIN FOR FUTURE REFERENCE • DO NOT use where hazardous dust is present. PRODUCT INFORMATION • DO NOT use machine near flammable liquids. • DO NOT use in an explosive atmosphere. This symbol is used in this manual to identify particular areas that are essential for your safety. Please pass all safety instructions on to other persons operating this machine. • DO NOT use on a gradient or slopes.
KNOW YOUR MACHINE (1) Top handle (2) Solution control handle (1) (2) (3) Solution tank (4) Bottom handle (5) Dirty water tank (6) Inline solution filter (3) (7) Component housing (8) Conveyor drum (9) Brush (10) Handle release pedal (4) (5) (6) (8) (7) (9) (5) 4 (10)
Warning! This machine is heavy. Do not attempt to lift the machine without assistance. Incorrect lifting techniques may result in personal injury. PREPARING FOR USE UNPACK (2) (1) (11) (4) (3) (9) (10) (5) (7) (6) (12) (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) Bottom handle Machine body Component housing Solution tank Top handle and solution cable Handle LH & RH Brush shafts (2) Screws & washers Cable retainer Power cord Dirty water tank Handle knobs (8) 1.
CONTROLS On/Off Control ON ON 2 OFF OFF 2 ON OFF 2 Release the pedal handle lightly with your foot (1), pull back the handle (2) to start the motor. The brushes and the drum starts rotating. Pulling the handle further without pressing the pedal, lowers the machine and engages the rotating brushes onto the floor. To stop working, take the handle to the vertical position. 1 1 1 Transport/Working Mode Control ON OFF 2 Slide this knob to TOP position (Working Mode) to operate the machine.
OPERATING THE MACHINE Before the washing operation starts (i) (i) Warning! Pre-sweep the floor to remove debris before using the Multiwash. 1. Verify that the brushes are fitted properly. ON ON 2. Fill fresh water tank with cleaning solution. 3. Insert the plug into grounded 3-pronged outlet. 3 3 OFF OFF 1 1 2 2 (ii) (ii) (i) 3 (i) sequence 1 Recommended washing ON 2 3 ON 2 OFF OFF 3 3 ON ON OFF OFF 1 1 1 (i) (i) (ii) (ii) 2.
CARE OF THE MACHINE Warning! Before cleaning the machine, switch off the machine and unplug from the electrical supply. 1. Move the Transport / Working mode control knob to BOTTOM (Transport) position (Fig-viii). 2. Disconnect the power supply by unplugging the electrical plug and wind the cable over cable holders in the handle. (viii) (viii) (viii) (viii) 3. Pull out the dirty water tank and wash it completely. 4.
BRUSH SELECTION GUIDE Type of floor First time cleaning Maintenance cleaning Grouted Tile, Ceramic, Mosaic, Wood, Sports floors, Rubber, Vinyl tile Short Pile Carpet Marble, Granite, Slate Smooth Concrete Escalator Others Standard Soft Soft Soft Soft Soft Hard Standard Escalator Escalator To suit individual floor conditions BRUSH IDENTIFICATION This is applicable when the customer has more than one set of brushes of same type. (a) (b) (a) Hole provided for plugging button.
ACCESSORIES Transport Cart The transport cart provides for ease of movement when transporting the machine. Warning! Empty all liquid from the machine before using the transport cart. Using the transport cart 1. With the machine handle in the upright position place the cart centrally alongside the machine. 2. By holding the machine firmly, tilt the handle away from your body. Slide the cart base under the machine and strap it to the machine with the velcro. 3.
W BK BR BR BL CBE R BR/W G/Y MOTOR BR BL SC N RC BL/BK ELECTRICAL DIAGRAM 928746 CAPACITOR 1. Electrical layout Diagrams are made available in the cover (Power cord side) of the respective machine for service purpose. Warning! Any service or attempt to service by persons other than authorized servicing agent will invalidate the warranty.
TECHNICAL SPECIFICATIONS Specification Cleaning capacity* Multiwash 14 Units square feet/hr Cleaning width inches Fresh water tank capacity gallons 5500 14 1 Overall dimensions Height with handle inches Height without handle inches Width inches Length inches Weight lbs. Noise level (see note 1) dB(A) Handle vibration (see note 2) m/s Model Multiwash 14 44" 8.5" 17.5" 15" 53 lbs. 69 2 <2.
For warranty information go to www.Powr-Flite.
