User's Manual

left stick
Ascend/descend rotate to left/right
ringt stick
orward/backward turn left/right
Unlock and take off
Attention: please check again to ensure the arms and legs are firm.
Put left joystick to bottom right position and put right joystick to bottom left
position, to have a “V” shape for about two to three seconds. Slowly put
joystick back to position after motors started
Slowly push the throttle to let the aircraft takeoff.
You can also choose to short press the takeoff/land button to let the aircraft
auto takeoff. It will withdraw the landing gear after rise to certain height
If you need to move aircraft, please refer to this graph below
You can change the control mode in App, as shown in graph
You can switch the flight mode between P mode, N mode and E mode
You can withdraw the landing gear during the flight. Long press the landing
gear button to withdraw the landing gear, short press to deploy it
You can control the gimbal to pitch and yaw though remote control
For example using right remote control dial or joystick of gimbal remote
control
Gimbal control
* You can switch to N mode only when there are enough satellites
① Control stick ② Takeoff/land button ③ Frequency-matching button
④ Return-to-Home button ⑤ Landing gear button
① Shutter button ② Flight mode switch ③ Gimbal dial ④ Micro USB port
⑤ Dual control connection port ⑥ Base station port ⑦ Camera parameter dial
⑧ Camera parameter switch ⑨ Picture/video mode switch
You can also control the gimbal pitch and yaw through app
① Click the bottom left widows to enter video interface
② Long press the screen and drag to any direction, gimbal will move to
desired direction
Switch to photo / video mode
Camera control
You can use the controller to control the camera
Press the left button to switch between photo mode and video mode
Press the right shutter button to take photos, or start/end video recording
Press this to button to shoot video or start/end video recording
Click any point on the video interface to focus
Photo and video mode switching
Video button Camera button
You can also control the camera through App
Press this button to switch between photo mode and video mode
Landing
When you need to land, fly to your landing position and pull the throttle to
land slowly
After aircraft lands, pull the throttle to the lowest position for a few
seconds to stop the motors and complete the landing
You can also press the landing button to auto land
*Attention: ensure the landing gear is deployed before landing, otherwise
aircraft could be damaged. If aircraft’s motors didn’t stop spinning, you can
pull the left joystick to bottom left, right joystick to bottom right and press
the Return-to-Home button at the same time to force lock the motors
Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
The antenna(s) used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not be
co-located or operating in conjunction with any other antenna or
transmitter.
This equipment complies with FCC radiation exposure limits set forth for
an uncontrolled environment. End user must follow the specific operating
instructions for satisfying RF exposure compliance. This transmitter must
not be co-located or operating in conjunction with any other antenna or
transmitter.
The portable device is designed to meet the requirements for
exposure to radio waves established by the Federal Communications
Commission (USA). These requirements set a SAR limit of 1.6 W/kg
averaged over one gram of tissue. The highest SAR value reported under
this standard during product certification for use when properly worn on
the body
IC:
This device complies with Industry Canada’s licence-exempt RSSs.
Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that
may cause undesired operation of the device.
Cet appareil est conforme aux CNR exempts de licence d'Industrie
Canada. Le fonctionnement est soumis aux deux conditions suivantes:
(1) Ce dispositif ne peut causer des interférences; et
(2) Cet appareil doit accepter toute interférence, y compris les
interférences qui peuvent causer un mauvais fonctionnement de l'appareil.
This equipment complies with ISED radiation exposure limits set forth for
an uncontrolled environment. End user must follow the specific operating
instructions for satisfying RF exposure compliance. This transmitter must
not be co-located or operating in conjunction with any other antenna or
transmitter.
The portable device is designed to meet the requirements for exposure to
radio waves established by the ISED. These requirements set a SAR limit of
1.6 W/kg averaged over one gram of tissue. The highest SAR value
reported under this standard during product certification for use when
properly worn on the body.
Cet équipement est conforme aux limites d’exposition aux rayonnements
ISED établies pour un environnement non contrôlé. L’utilisateur final doit
suivre les instructions spécifiques pour satisfaire les normes. Cet émetteur
ne doit pas être co-implanté ou fonctionner en conjonction avec toute
autre antenne ou transmetteur.
Le dispositif portatif est conçu pour répondre aux exigences d’exposition
aux ondes radio établie par le développement énergétique DURABLE. Ces
exigences un SAR limite de 1,6 W/kg en moyenne pour un gramme de
tissu. La valeur SAR la plus élevée signalée en vertu de cette norme lors de
la certification de produit à utiliser lorsqu’il est correctement porté sur le
corps.
FCC
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
Declaration of Conformity
Product Name/
PowerEye
PowerEye Base Station
Model Number
PEY10
PEGRS10
PEYSC10
Applicable Harmonized Standards
We herewith confirm the following designated products to comply with the
requirements set out in the Council Directive on the approximation of the laws
of the Member States relating to R&TTE Directive 1999/5/EC or RED
2014/53/EU and EMC Directive 2014/30/EU and ROHS Directive 2011/65/EU
with applicable standards listed below.
PowerEye Standard
Controller
EN 301 489-1 V1.9.2 (2011-09)
EN 301 489-3 V1.6.1 (2013-08)
EN 301 489-17 V2.2.1 (2012-09)
EN 300 328 V1.9.1 (2015-02)
EN 300 440-1 V1.6.1 (2010-08)
EN 300 440-2 V1.4.1 (2010-08)
EN 62311:2008
EN 60950-1:2006+A11:2009+A1:2010
+A12:2011+A2:2013
IEC 62321
EN 55022:2010
EN 55024:2010+A1:2015
EN 61000-3-2:2014
EN 61000-3-3:2013
EN 301 489-1 V1.9.2 (2011-09)
EN 301 489-3 V1.6.1 (2013-08)
EN 301 489-17 V2.2.1 (2012-09)
EN 300 328 V1.9.1 (2015-02)
EN 300 440-1 V1.6.1 (2010-08)
EN 300 440-2 V1.4.1 (2010-08)
EN 50566:2013+AC:2014
EN 60950-1:2006+A11:2009+A1:2010
+A12:2011+A2:2013
IEC 62321
EN 55022:2010
EN 55024:2010+A1:2015
EN 61000-3-2:2014
EN 61000-3-3:2013
EN 301 489-1 V1.9.2 (2011-09)
EN 301 489-3 V1.6.1 (2013-08)
EN 300 440-1 V1.6.1 (2010-08)
EN 300 440-2 V1.4.1 (2010-08)
EN 62479:2010
EN 60950-1:2006+A11:2009+A1:2010
+A12:2011+A2:2013
IEC 62321
11 12 13 14
Person in responsible for making this declaration:
Applicant: Powervision Tech Inc.
Address:
Telephone: [phone]
Room 301, Building A,No.9 Fulin Road, Chaoyang District,
Beijing, 100107, China
Full Name
Legal Signature
Title
Date
Vice PresidentHan Hui
Dec. 20th
2016
C
M
Y
CM
MY
CY
CMY
K
powereye英文版说明书+CE合规声明12.8.pdf 2 2016/12/8 10:22:31