User's Manual

Quick Start Guide
Brief introduction
Attention
Preparing for your first flight
Thank you for choosing PowerEye! Reading this Quick Start Guide will help
you learn about the basic functions of PowerEye as well as some of the basic
skills needed for flight.
This drone is not a toy. It requires a basic understanding of the features and
controls to operate and it can be dangerous. Please use and operate
responsibly.
It’s a good idea to do some test flights in a familiar, wide open space to get
familiar with the operations and features. Note: flight restrictions very by
location and some areas may require a permit to fly. If you’re unsure contact
you local authorities, but in general avoid the following locations:
Also be wary in flying under the following conditions, as it is not recommend-
ed:
① Airport and surrounding areas
② Power generator and surrounding areas
③ Military facilities ④ Oilfield ⑤ Crowded area
Please check the following prior to taking PowerEye for its first flight:
① Non-ideal weather conditions (extreme windy, rainy, thunderstorm,etc.)
② In Arctic or Antarctic circle ( can NOT use any mode other than Manual
mode)
③ Altitude above 3000m
① PowerEye aircraft is assembled correctly,
with all connections tight (see below)
② Fully charged PowerEye
Intelligent battery
③ Fully charged PowerEye controller
④ Fully charged Base Station
If you choose to have a separate gimbal and camera operator, you need a
second PowerEye controller.
⑤ Ensure the base station connection
cable is connected properly
Power indicator light
Aircraft
PowerEye’s arms are foldable and the legs of are easily removable. Follow
these steps to ensure the aircraft is ready for flight:
PowerEye features an intelligent battery that when the status button is
pressed will indicate via the four LED lights the charge level of the battery.
We highly recommend not flying PowerEye when the battery level is below
50%
① Raise the arms to horizontal position
② Push the locking nut to the inside
③ Rotate the nut clockwise to tighten, ensuring arms are secure
④ Insert the legs into the aircraft and rotate until locked into place
Intelligent battery
Please use those ports to connect
Red/green light flashes
Flight Prep and connection
Connect to remote control system
① Unfold base station holder
② Put base station on the holder, and open the antenna
③ Connect base station and remote control with cable
④ Long press the power button of base station and remote control for
three seconds to power on
① After connecting one remote control to the base station, long press the
frequency-matching button until you hear a notification sound, and it
flashes a red light. Long press the second remote control’s
frequency-matching button until it also makes a notification sound, and
it’s light flashes red.
② After a few seconds the two remote controls will show green lights,
Indicating a successful connection.
Attention: every time that you reboot any remote controller, you need to
redo the frequency matching.
If you need to use extra a second controller to control the gimbal, you need
to do those following steps
WLAN
PowerEye_Station_XXXXX
Password
Enter Password
1234567890
② Turn on the mobile device WiFi and search for “PowerEye_Station_XXXXX”
③ Connect to the WiFi network using password “1234567890” to join
④ Ensuring a successful connection, return to the Vision+ App
Please put the aircraft at least 5m (~15 feet) away, and face the aircraft away
from the pilot. Use Vision+ app to check aircraft status
Number of GPS satellites: If you need to use normal mode to flight outdoor,
ensure the number of GPS satellites is greater than ten.
Base station/aircraft battery: we don’t recommend flying when the battery
level is under 50%
App looks like this
Takeoff and flight
Turn on the power switch
Turn on the aircraft
Connection between base station and aircraft
connection between basestaion and smart mobile device
The process of turning on the aircraft:
① Open the battery door and put the battery in the compartment.
② Short press and hold the battery switch of aircraft, until you see the LED
light running to the end. Release the button to start the aircraft. The
power button of aircraft will be lit and the battery indicator will represent
the battery level.
③ Close the battery door.
When aircraft or base station is turned on, the internal communication
module will automatically establish the connection. It usually takes about 50
seconds. When the status lights are all green the connection is established.
When the remote control and base station have established a connection a
notification sound will be heard.
After your mobile device has installed the Vision+ App, you’ll need to
connect to the base stations via WiFi.
① Ensure the base station is powered on
C
M
Y
CM
MY
CY
CMY
K
powereye英文版说明书+CE合规声明12.8.pdf 1 2016/12/8 10:22:31