Owner's Manual Model No. DC5372 Portable Dust Collector Visit us on the web at www.powertecproducts.com You will need this manual for safety instructions, operating procedures, and warranty.
TABLE OF CONTENTS SECTION SAFETY RULES / WARNINGS PRODUCT SPECIFICATIONS PAGE 1-2 Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-HP, 120 or 240 V, 60-Hz, 1PH (pre-wired to 120) Motor Speed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 RPM Bearings. . . . . . . . . . . . . . . .
WARNING For your own safety, read and understand all warnings and operating instructions before using any tool or equipment. WARNING Some dust created by power sanding, sawing, grinding, drilling and other construction activities can expose you to chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints. • Crystalline silica from bricks and cement and other masonry products.
SAFETY RULES IMPORTANT SAFETY WARNINGS 2 NOTE: When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING (THIS APPLIANCE) WARNING 2 To reduce the risk of fire, electric shock, or injury: a. Do not leave appliance when plugged in. Unplug from outlet when not in use and before servicing. b. Do not allow to be used as a toy. Close attention is necessary when used by or near children. c.
UNPACKING 3 Refer to Figure 2 Refer to Figure 1 Check for shipping damage. Check immediately whether all parts and accessories are included. If anything is missing or broken, contact your retailer or call 847-780-6120. NOTE: Carefully remove all contents from shipping carton. The shipping carton contains: ITEM DESCRIPTION A Motor with Paddle Switch and Dust Box 1.
ASSEMBLY 3. Place the adhesive foam strip (supplied) around the dust POWER SOURCE WARNING 4. Place the dust collector bag onto the outlet port and secure Do not connect dust collector to the power source until all assembly steps have been completed. Figure 4 The motor is designed for operation on the voltage and Collection Bag 4 Bag Clamp Running the unit on voltages which are not within the range may cause overheating and motor burn-out.
• The use of an extension cord is not recommended. The use of any extension cord will cause some drop in voltage and loss of power. • the current and maintain adequate voltage. • Use the table to determine the minimum wire size (A.W.G.) extension cord. • Use only 3-wire extension cords having 3-prong grounding type plugs and 3-pole receptacles which accept the tool plug. • If the extension cord is worn, cut or damaged in any way, Replace it immediately. ELECTRICAL CONNECTIONS WARNING electrician.
ASSEMBLY TO CONVERT 1. 2. 3. Follow the 240V wiring diagram on the inside of the switch box cover. NOTE: The 240V wiring diagram is also in 847-780-6120 for 5. Replace the plug on the existing power cord with a NEMA 6-15 plug. The plug must be plugged into matching outlet that is properly installed and grounded in accordance with all local codes and ordinances. 4. After rewiring make sure all wire nuts are tight and use 6. 7.
GENERAL MAINTENANCE 7 LUBRICATION MAINTENANCE MAINTENANCE The sealed bearings in the motor have been permanently lubricated at the factory. They require no further lubrication. WARNING Make sure the machine is turned off and the cord is disconnected from the power source before servicing and removing/replacing any components on the machine. MACHINE STORAGE • Check the dust collector daily for loose mounting bolts, screws, damaged wires, worn switch, full collection bag and any other unsafe condition.
PARTS LIST 8 FENCE ASSEMBLY DUST COLLECTOR PARTS ILLUSTRATION 8 DUST COLLECTOR PARTS LIST 8 Part No 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 DC5372001 DC5372002 DC5372003 DC5372004 DC5372005 DC5372006 DC5372007 DC5372008 DC5372009 DC5372010 DCS371011 DC5372012 DC5372013 DC5372014 DCS371015 DC5372016 DC5372017 DCS371018 DC5372019 DC5372020 DCS371021 DC5372022 DC5372023 DC5372024 DC5372025 Description Main housing Inlet cover 4" Motor plate Base Impeller 10" Socket head cap s
9 WARRANTY WARRANTY Thank you for investing in a POWERTEC power tool. This product has been designed and manufactured to meet high quality standards and is guaranteed for domestic use against defects in workmanship or material for a period of 12 months from the date of purchase. This guarantee does not affect your statutory rights. SOUTHERN TECHNOLOGIES LLC.
Southern Technologies, LLC Chicago, IL 60606
