Manual

For full specications and order information please visit www.deltapowersupplies.com
D E LTA ELEKTRONIKA
DC POWER SUPPLIES
D E LTA ELEKTRONIKA
DC POWER SUPPLIES
22 23
For full specications and order information please visit www.deltapowersupplies.com
PSC Series
interFaCeS
Specications
• Programming and
monitoring resolution: 14 bit
• Communication speed:
up to 12Mbit/s for PSC-PB
up to 1Mbit/s for PSC-CAN
• Full scale accuracy: < 0.1%
Functionalities
CANopen Functionalities:
• SYNC Object
• Emergency Object
• Node Guarding
• Heartbeat
• Expedited and Nonexpedited SDO transfer
• Node address range 1 - 127
Features
• Voltage and current
programming and monitoring
• Node address setting selectable
• Read back of power
supply status signals
• 600 V galvanic isolation
• Factory installed
Interface
PSC-ETH Ethernet Controller
PROFIBUS Functionalities:
• Slave in a PROFIBUS-DP network
• DP-V0 standard acc. IEC 61784 Ed.
1:2002 CPF 3/1
• PROFIBUS protocol acc. IEC 61158
• Slave address range 1 - 127
PSC Series
interFaCeS
Features
• Voltage and current
programming and monitoring
• Up to 15 PSCs on one BUS
• Software calibration
• Isolated digital user
in- and outputs
• Factory installed or
external module
Functionalities
• Monitoring status outputs: ACF, DCF, CC-
mode, Over Temp, PSOL etc.
• Two isolated user inputs and outputs
(external modules only)
• Software calibration for oset and full scale
• PSC-488 Units can also be congured as
PSC-232
Dimensions and weight:
Dimensions: 89 x 86 x 119 mm
Weight: 0,8 kg
Optional 19” rack mounting
Specications
• Programming and
monitoring resolution: 16 bit
• Linearity error: +/- 2 LSB (prg.)
+/- 1 LSB (mon.)
TC = 10 ppm/°C
• Input voltage
(external module): 98-264 V AC (48-62 Hz)
External module
PSC-232/488
Standards:
• Generic Emission: EN 61000-6-3 (EN 55022B)
• Generic Immunity: EN 61000-6-2
• Safety: EN 60950 / EN 61010
• Insulation input / output: 1000 V
rms
• Enclosure: IP20
Features
• Voltage and current program-
ming and monitoring
• Uses existing IP-networks
• Integrated sequencer
• Software calibration
• Isolated digital user in- and outputs
• Factory installed or external module
Specications
• Programming and
monitoring resolution: 16 bit
• Linearity error: +/- 2 LSB (prg.)
+/- 1 LSB (mon.)
TC = 10 ppm/°C
• Input voltage (external module): 98-264 V AC (48-62 Hz)
Integrated sequencer:
• Converts power supply into an arbitrary waveform generator
• Stand-alone automation like a PLC
• 25 free programmable sequences, 2000 steps each
• Combination of very fast and slow sequences
• Possibility to create loops, sub-routines, ramps etc.
Sequencer
Interface:
• Monitoring status outputs: ACF, DCF,
CC-mode, Over Temp, PSOL etc.
• Isolated user inputs (8) and outputs (6)
• Software calibration for o-
set and full scale
Software Control
& Interfaces
Functionalities
External module PSC-ETH
Standards:
• Generic Emission EN 61000-6-3 (EN 55022B)
• Generic Immunity EN 61000-6-2
• Safety EN 60950 / EN 61010
• Insulation
in/outputs - case 1000 V
DC
• Enclosure IP20
Dimensions and weight:
Dimensions: 89 x 86 x 119 mm
Weight: 0,7 kg
Optional 19” rack mounting
Interfaces
PSC-CAN CANopen Controller
PSC-PB PROFIBUS Controller
Interfaces
PSC-232 RS232 Controller
PSC-488 IEEE488 Controller