INSTRUCTION MANUAL Pneumatic 21ºRound Head Framing Nailer Model # PS6120 Have product questions or need technical support? Please feel free to contact us! Website: www.Amerisuninc.com Toll free: 1-800-791-9458 M-F 9-5 EST Email: support@amerisuninc.
CONTENTS Technical data…...………………………………………………………... General safety rules…….………………………………………………... Knowing your framing nailer ..………………………………………….. Assembly ………………………………………………………………… Operating instruction…………………………………………………...... Maintenance.……………………………………………………………… Troubleshooting………………………………………………………….
GENERAL SAFETY RULES Safety is a combination of common sense, staying alert, and knowing how your framing nailer works. SAVE THESE SAFETY INSTRUCTIONS. WARNING: Do not operate this unit until you read this instruction manual for safety, operation and maintenance instructions. WARNING: This product contains chemicals known to the State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling.
contact trip is adjusted when the tool is connected to the air supply and nails are loaded, accidental discharge may occur. Connect tool to air supply before loading fasteners, to prevent a fastener from being fired during connection. The tool driving mechanism may cycle when tool is connected to the air supply. Do not load fasteners with trigger or contact trip depressed, to prevent unintentional firing of a fastener.
Refer to the Maintenance and Repairs sections for detailed information on the proper maintenance of the tool. Always operate the tool in a clean, lighted area. Be sure the work surface is clear of any debris and be careful not to lose footing when working in elevated environments such as rooftops. Do not drive fasteners near edge of material. The workpiece may split causing the fastener to ricochet, injuring you or a co-worker.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well-ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. • • • WARNING: ALWAYS USE SAFETY GLASSES. Everyday eyeglasses are NOT safety glasses. Also use face or dust mask if operation is dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT: ANSI Z87.1 eye protection (CAN/CSA/Z94.
KNOWING YOUR FRAMING NAILER D E G C A F B A B E G Magazine Safety contact trip 1/4" Air quick coupler Magazine latch C D F Trigger Exhaust deflector Magazine handle Unpacking Unpack the framing nailer and all its parts, and compare against the list below. Do not discard the carton or any packaging materials. Please call 1-800-791-91458 or E-mail us at support@amerisuninc.com if any parts are damaged or missing.
ASSEMBLY WARNING: Disconnect air line from tool and remove fasteners from magazine before making adjustments or personal injury may result. AIR FITTING This tool uses a 1/4" N.P.T. male plug. The inside diameter should be 0.180" (4.6 mm) or larger. The fitting must be capable of discharging tool air pressure when disconnected from the air supply. WARNING: Always use couplings that relieve all pressure from the tool when it is disconnected from the power supply.
Loading WARNING: Keep the tool pointed away from yourself and others. Serious personal injury may result. WARNING: Never load nails with the contact trip or trigger activated. Personal injury may result. When replacing nails in your model PS6120, follow these guidelines: Nail Type: 21 degree round head framing nail Length: 2"-3 1/2" Diameter: 0.113" – 0.130" Capacity: 60 pcs To load your nailer: Figure 1 1. Disconnect nailer from the air supply! 2.
5. Pull the trigger. -If the nail drove into the wood for enough, continue with your intended operations. -If the nail either went too far or not far enough, then refer to Adjusting Depth subsection. WANRNING: During operation, this nailer can propel objects into the air and exhaust concentrated bursts of air, causing immediate eye damage. To reduce your risk from these hazards, always wear ANSI approved safety galsses or a face shield.
2. Never exceed maximum and minimum pressure. Too low or too high pressure would cause noise wear and tear or misfiring. 3. When connecting air supply always keep hands and body away from discharge area of tool. 4. A filter- regulator-lubrication is required and should be located as close to tool as possible. 5. Keep air filter clean. A dirty filter will reduce the air pressure to the tool causing a reduction in power and efficiency. 6.
TROUBLE SHOOTING The following form lists the common operating system with problem and solutions. Please read the form carefully and follow it. WARNING: If any of the following symptoms appears during your operating, stop using the tool immediately, or serious personal injury could result. Only a qualified persons or an authorized service center can perform repairs or replacement of tool. Disconnect tool from air supply before attempting repair or adjustment.
Qty 1 Item Stock # PS6120-001 Description Bolt M8x16 49 PS6120-002 Exhaust deflector 1 50 PS6120-049 PS6120-050 Safety yoke 1 PS6120-003 Deflector rubber 1 51 PS6120-051 Bolt M5x10 1 Spring washer 5 4 Item Stock # 1 2 3 Description Compression spring Qty 1 4 PS6120-004 Compression spring 1 52 PS6120-052 5 PS6120-005 Spring wire 1 53 PS6120-053 Flat washer 5 3 6 PS6120-006 Bolt M6x30 4 54 PS6120-054 Safety nose 1 7 PS6120-007 Spring washer 6 6 55 PS6120-0
TWO (2) YEARS LIMITED WARRANTY PowerSmart® is committed to building tools that are dependable for years. Our warranties are consistent with our commitment and dedication to quality. TWO (2) YEARS LIMITED WARRANTY OF POWER SMART PRODUCTS FOR HOME USE. PowerSmart (“Seller") warrants to the original purchaser only, that all PowerSmart consumer power tools will be free from defects in material or workmanship for a period of two (2) years from date of purchase.
