INSTRUCTION MANUAL 8 Inch Drill Press with Laser Guide Model # PS308 Have product questions or need technical support? Please feel free to contact us! Website: www.Amerisuninc.com www.PowerSmartUSA.com Toll free: 1-800-791-9458 M-F 9-5 EST Email: support@amerisuninc.
CONTENTS Technical data…...………………………………………………………... General safety rules…….………………………………………………... Specific safety rules for drill press……...………………………………. Electrical information…………………………………………………...... Knowing your drill press……...………………………………………… Assembly and adjustments……………………………………………… Maintenance.…………………………………………………………… Troubleshooting.………………………………………………………...
GENERAL SAFETY RULES Safety is a combination of common sense, staying alert, and knowing how your drill press works. SAVE THESE SAFETY INSTRUCTIONS. WARNING: To avoid mistakes that could cause serious injury, do not plug in the drill press until the following steps have been read and understood. 1. READ and become familiar with this entire instruction manual. LEARN the tool’s applications, limitations, and possible hazards. 2. AVOID DANGEROUS CONDITIONS.
15. DO NOT OVERREACH. Keep proper footing and balance at all times. Wear oil-resistant rubber-soled footwear. Keep the floor clear of oil, scrap, and other debris. 16. MAINTAIN TOOLS PROPERLY. ALWAYS keep tools clean and in good working order. Follow instructions for lubricating and changing accessories. 17. CHECK FOR DAMAGED PARTS. Check for alignment of moving parts, jamming, breakage, improper mounting, or any other conditions that may affect the tool’s operation.
ELECTRICAL INFORMATION Grounding instructions IN THE EVENT OF A MALFUNCTION OR BREAKDOWN, grounding provides the path of least resistance for electric current and reduces the risk of electric shock. This tool is equipped with an electric cord that has an equipment grounding conductor and a grounding plug. The plug MUST be plugged into a matching outlet that is properly installed and grounded in accordance with ALL local codes and ordinances. DO NOT MODIFY THE PLUG PROVIDED.
Guidelines for using extension cords Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The table below shows the correct size to be used according to cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.
KNOWING YOUR DRILL PRESS 10 1 2 9 8 3 7 6 4 5 1 2 3 4 5 Belt cover On/Off Switch Chuck Work table Base 6 7 8 9 10 8 Lock handle Column assembly Motor Feed handle Belt tension lock knob
ASSEMBLY AND ADJUSTMENTS Unpacking Unpack the drill press and all its parts, and compare against the list below. Do not discard the carton or any packaging until the drill press is completely assembled.
Tools needed for assembly - Adjustable wrench Hammer and block of wood Screwdriver Base to column 1 1. Place Column (1) on the Base (2) and align holes in the Column with holes in the Base. 2. Attach using Bolt, Spring Washer, and Washer (2) in each hole through the Column and into the Base. 2 3 Table to column 1 1. Loosen the Pivot Lever (3) on the table. (2). 2. Slide the Table (2) over the Column (1). 3. Tighten the Pivot Lever (3) to secure the Table (2) in place.
Remove the chuck at a later time 1. Turn the feed handles to lower the chuck (2) to the lowest position. 2. Place a ball joint separator tool (not included, not shown) above the chuck (3) and tap it lightly with a hammer (4) to cause the chuck to drop from the spindle. Note: To avoid possible damage, be prepared to catch the chuck as it falls.
Adjustments Spindle speeds This drill press offers 5 spindle speeds from 760 to 3070 RPM. The highest speed is obtained when the belt is positioned on the largest motor pulley step and the smallest spindle pulley stop. WARNING: Disconnect the drill press from the power source before making any speed adjustments. 1 Adjust speeds and tension the belt 2 1. 2. 3. 4. Open the drill press pulley cover. Loosen the belt tension knob (1). Pull the motor (2) toward the drill press head.
Coil spring adjustment WARNING: Disconnect the drill press from the power source. If the quill returns too quickly or too slowly when the feed handles are released, adjust the spring. Note: This adjustment is set at the factory and should not need changing. Readjustments may eventually be necessary due to normal wear and tear. 1. Raise the spindle to the top position. 2. Move both depth scale nuts (1) to the lowest position and tighten to prevent the quill from dropping down. 3.
MAINTENANCE Warning: Turn the power switch “OFF” and disconnect the plug from the outlet prior to adjusting or maintaining the machine. DO NOT attempt to repair or maintain the electrical components of the motor. Contact a qualified service technician for this type of maintenance. Before each use: - Check the power cord and plug for any wear or damage. - Check for any loose screws or hardware. - Check the area to make sure it is clear of any misplaced tools, lumber, cleaning supplies, etc.
TROUBLESHOOTING 15
EXPLODED VIEW & PARTS LIST 16
Item Stock # Description Item Stock # Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 PS308-001 PS308-002 PS308-003 PS308-004 PS308-005 PS308-006 PS308-007 PS308-008 PS308-009 PS308-010 PS308-011 PS308-012 PS308-013 PS308-014 PS308-015 PS308-016 PS308-017 PS308-018 PS308-019 PS308-020 PS308-021 PS308-022 PS308-023 PS308-024 PS308-025 PS308-026 PS308-027 PS308-028 PS308-029 PS308-030 PS308-031 PS308-032 PS308-033 PS308-034 PS308-0
ONE (1) YEAR LIMITED WARRANTY PowerSmart® is committed to building tools that are dependable for years. Our warranties are consistent with our commitment and dedication to quality. ONE (1) YEAR LIMITED WARRANTY OF POWER SMART PRODUCTS FOR HOME USE. PowerSmart (“Seller") warrants to the original purchaser only, that all PowerSmart consumer power tools will be free from defects in material or workmanship for a period of one (1) year from date of purchase.
