User Manual

ManualsBrandsPowerplus ManualsPower sawsPOWX1365 MINI CIRCULAR SAW 600W 85MM + MITRE GUIDE EN

POWX1365 EN

1 APPLICATION .................................................................................. 3

2 OVERVIEW COMPONENTS (FIG. A).............................................. 3

3 PACKAGE CONTENT LIST ............................................................. 3

4 SYMBOLS ........................................................................................ 4

5 GENERAL POWER TOOL SAFETY WARNINGS .......................... 4

5.1 Work area ................................................................................................................ 4

5.2 Electrical safety ....................................................................................................... 4

5.3 Personal safety ....................................................................................................... 5

5.4 Power tool use and care ......................................................................................... 5

5.5 Service ..................................................................................................................... 5

6 SPECIFIC SAFETY WARNINGS FOR CIRCULAR SAWS............. 5

7 ASSEMBLY ...................................................................................... 6

7.1 Setting the cutting depth (fig 1).............................................................................. 6

7.2 Changing a saw blade............................................................................................. 6

8 OPERATION ..................................................................................... 7

8.1 Holding and switching ON/OFF .............................................................................. 7

8.1.1 Switching on the tool: ................................................................................................ 7

8.1.2 Releasing the plunge stop ......................................................................................... 7

8.2 Setting the guide fence ........................................................................................... 7

8.3 Laser line generator ................................................................................................ 7

8.4 Line following .......................................................................................................... 8

8.5 Dust extraction ........................................................................................................ 8

9 CUTTING .......................................................................................... 8

10 CUT-OUTS ....................................................................................... 9

11 CUTTING PARTICULARLY TOUGH OR ABRASIVE MATERIALS

.......................................................................................................... 9

11.1 Sheet metal:............................................................................................................. 9

11.2 Ceramic tiles, slates etc: ........................................................................................ 9

11.3 Plasterboard: ........................................................................................................... 9

12 CLEANING AND MAINTENANCE ................................................. 10

Summary of content (12 pages)

PAGE 1
POWX1365 EN 1 APPLICATION .................................................................................. 3 2 OVERVIEW COMPONENTS (FIG. A).............................................. 3 3 PACKAGE CONTENT LIST ............................................................. 3 4 SYMBOLS ........................................................................................ 4 5 GENERAL POWER TOOL SAFETY WARNINGS .......................... 4 5.1 Work area .........................................
PAGE 2
POWX1365 EN 12.1 Blades .................................................................................................................... 10 13 TECHNICAL DATA ........................................................................ 10 14 NOISE ............................................................................................. 10 15 WARRANTY ................................................................................... 11 16 ENVIRONMENT ...........................................
PAGE 3
EN POWX1365 MINI CIRCULAR SAW 600W POWX1365 1 APPLICATION This machine is primarily intended for the sawing, longitudinally and transversely, of solid wood, chipboard, plywood, aluminium, tiles and stone held in a fixed position. Please note that the blade pre-installed in the saw as supplied is intended for use with wood only. Any other use or modification to the device shall be considered as improper use and could give rise to considerable dangers. Not suitable for commercial use.
PAGE 4
EN POWX1365 4 SYMBOLS In this manual and/or on the machine the following symbols are used: Class II - The machine is double Denotes risk of personal insulated; Earthing wire is injury or damage to the tool. therefore not necessary. Read the manual carefully before use. Always wear safety goggles. In accordance with essential requirements of the European directive(s). 5 GENERAL POWER TOOL SAFETY WARNINGS Read all safety warnings and all instructions.
PAGE 5
EN POWX1365 5.3 Personal safety  Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.  Use safety equipment. Always wear eye protection.
PAGE 6
EN POWX1365         7 7.1 Never hold piece being cut in your hands or across your leg. Secure the workpiece to a stable platform. Hold power tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. When ripping always use a rip fence or straight edge guide. Always use blades with correct size and shape (diamond versus round) of arbor holes. Never use damaged or incorrect blade washers or bolt.
PAGE 7
POWX1365 8 8.1 EN OPERATION Holding and switching ON/OFF WARNING: Before engage the ON/OFF switch, check that the saw blade is properly fitted and runs smoothly, and that the blade clamp screw (8) is well tightened. Connect the plug to the power supply. The LED power-on indicator (14) is illumed until the tool is disconnect from the power mains. 8.1.1 Switching on the tool: Push the lock-off button (6) forward with the forefinger (refer to the direction of arrow ① on Fig.
PAGE 8
POWX1365     EN When the blade is at its maximum speed (approximately 5 seconds), place the saw on the work-piece. Switch on the laser generator (1) from the laser aperture using the laser generator switch (2). Align the beam with the mark on the work-piece and slowly push the saw forward using both hands, keeping the red light beam on the mark. Switch off the laser beam when completion of the cut. 8.
PAGE 9
POWX1365  10 EN Once the cut has been finished, lift the tool from the work surface before switching off. If a lot of dust has been created, keep switched on for a few seconds extra to allow the dust to clear from within the tool. CUT-OUTS Plunge cutting may not be possible in some hard materials.  Choose a suitable saw blade for hard materials and change to it.
PAGE 10
EN POWX1365  Conventional tools such as keyhole saws or knives generally give excellent results, though the plunge saw can be used if a particularly neat, dust free cut is required or if there is a danger of cutting pipes or cables. 12 CLEANING AND MAINTENANCE Regular cleaning is required for the safe operation of the tool, as an excessive build up of dust will prevent the tool from operating correctly.
PAGE 11
POWX1365 15               16 EN WARRANTY This product is warranted as provided by law for a 36 -month period effective from the date of purchase by the first user. This warranty covers all material or production flaws excluding : batteries, chargers, defective parts subject to normal wear & tear such as bearings, brushes, cables, and plugs, or accessories such as drills, drill bits, saw blades, etc.
PAGE 12
17 EN POWX1365 DECLARATION OF CONFORMITY VARO N.V. - Joseph Van Instraat 9 - BE2500 Lier - BELGIUM, declares that, Product: mini circular saw 600W Trade mark: POWERplus Model: POWX1365 complies with the essential requirements and other relevant provisions of the applicable European Directives, based on European harmonized standards. Any unauthorized modification of the apparatus voids this declaration.