Product Manual

ManualsBrandsPowermatic ManualsPower ToolsTable Saw — 1 3/4 HP, 115/230V, 30in. Accu-Fence with Riving Knife

Motor and Electricals:

Motor type.................................................................................. totally enclosed fan cooled, induction, capacitor start

Horsepower ..................................................................................................................................... 1-3/4 HP (1.3 kW)

Phase ................................................................................................................................................................. single

Voltage ............................................................................................................................... 115/230V (prewired 115V)

Cycle .................................................................................................................................................................. 60 Hz

Motor speed................................................................................................................................................. 3450 RPM

Listed FLA (full load amps) ..............................................................................................................................15/7.5 A

Starting amps ........................................................................................................................................................ 52A

Running amps (no load) .......................................................................................................................................... 6A

Start capacitor .................................................................................................................................. 400MFD 125VAC

Run capacitor ............................................................................................................................................. 30F 250V

Power transfer ..................................................................................................................................................... v-belt

On/off switch ................................................................................................ manual industrial-style, with padlock hole

Power cord length ..................................................................................................................................... 7 ft. (213cm)

Power plug installed ............................................................................................................................................... yes

Recommended circuit size

...................................................................................... 30A (for 115V) or 20A (for 230V)

Noise emission:

Without load ............................................................................................................. 78 dB at 20 inches from blade

With load.................................................................................................................. 85 dB at 20 inches from blade

Arbor and blade:

Blade Diameter

(in.) ............................................................................................................................... 10” (254mm)

Arbor Diameter (in.) .................................................................................................................................. 5/8” (16mm)

Arbor speed ................................................................................................................................................. 3800 RPM

Arbor lock ............................................................................................................................................................... yes

Maximum cut depth at 90 degrees ........................................................................................................ 3-1/8” (79mm)

Maximum cut depth at 45 degrees ........................................................................................................ 2-1/8” (54mm)

Maximum rip to right of blade ....................................................................................... 30” (762mm) or 50” (1270mm)

Maximum rip to left of blade..................................................................................................................... 12” (305mm)

Dado maximum width .......................................................................................................................... 13/16” (20.7mm

Dado maximum diameter .......................................................................................................................... 8” (200mm)

Blade height per one revolution of handwheel ............................................. 5/32” (4mm) for 90°; 1/8” (2.9mm) for 45°

Blade tilt ..................................................................................................................................................... left, 0 to 45°

Table:

Table working surface ............................................................................................. 20-1/8” L x 27” W (511 x 686mm)

Table working surface, with extensions ................................................................. 44-1/4” L x 27” W (1124 x 686mm)

Table working surface, with extensions and optional wood table:

With 30” rip capacity ......................................................................................... 71-1/4” L x 27” W (1810 x 686mm)

With 50” rip capacity ............................................................................................... 80” L x 27” W (2022 x 686mm)

Table area in front of blade at maximum height................................................................................. 11-1/2” (292mm)

Table height from floor ............................................................................................................................. 36” (914mm)

Miter slot ...................................................................................................... two T-slots, 3/4" W x 3/8” D (19 x 10mm)

Edge bevel............................................................................................................................................................. front

Dust collection:

Dust port outside diameter ........................................................................................................................ 4” (100mm)

Minimum extraction volume required .............................................................................................. 350 cfm (9.9 cmm)

Other:

Stand style ............................................................................................................................................................ open

Stand footprint ............................................................................................................ 21-1/2”L x24”W (546 x 610mm)

Overall Dimensions, shipping carton (basic saw only) ........................... 39” L x 25” W x 22” H (98.6 x 63.6 x 56.4cm)

Overall Dimensions, fully assembled, accessories mounted:

With 30” rip capacity ...................................................................... 71-1/4” L x 43” W x 42” H (181 x 109 x 107cm)

With 50” rip capacity ...................................................................... 79-5/8” L x 43” W x 42” H (202 x 109 x 107cm)

Weights:

Net ........................................................................................................................................................ 293 lb (133 kg)

Shipping ............................................................................................................................................... 304 lb (138 kg)

subject to local and national electrical codes.

blade not included.

L=length, W=width, H=height