UserManual PN-G Panther 2G Wireless Communication Device January 2019 R1.0 Theinformationpresentedinthisdocumentisstrictlyconfidentialandcontainstradesecrets and otherconfidentialinformation that are the exclusive propertyof M-Labs Technologies,LLC. Author Revision Changes Date 1.
Contents 1 Introduction ....................................................................................................................................... 3 2 HardwareDesign .......................................................................................................................... 4 2.1 Basic Hardware .................................................................................................................... 4 GPS ..................................................................
1 Introduction ThePN-Gisaself-containedvehicletrackingdevicethatcombinesGPSlocationwith2Gcellular connectivity. It is primarily a location reporting device that responds to requests (user, server) and events (timers, geo-fences). Data reports consist of a single record that contains all location data and system status. The device comes pre-configured from the factory. It is ready to use. ThePNGappearstoauseroraserverapplicationasanendpointdevice.
2 HardwareDesign 2.1 Basic Hardware Items Requirement Cellular Modem Based Mediatek 2503x chipset, GPRS Class 10 Cellular Network Interface Frequency Support for 850, 900, 1800, 1900 GPS Antenna UIM requirement Dedicate high performance ceramic antenna BatteryMonitor Buildinbatterymanager Bluetooth Interface Internal analog input GSM850: 824.20MHz-848.80MHz E-GSM900: 880MHz~915MHz DCS1800: 1710MHz~1785MHz PCS1900: 1850.20MHz-1909.
GPIO One dedicated input, two dedicated outputs, and one general purpose IO are presentedtotheexternalenvironmentonthemainconnector. They are capable of providing system interrupts to generate are port or drive logic levels to external devices. These lines are 2.8V logical velandare16V tolerant. These pins default to input and are pulled down representing 0 when disconnected. They should be asserted to a known value if used. LED’s TwoLEDstatusindicatorsareprovidedto verifycorrectinstallationandoperation.
Timers Timersresidentonthebasebandchipgenerateperiodicinterrupts forpowerdownwakeup, watchdogsupport,periodic reportgeneration andothertimerrelatedfunctions. Watchdog The providesinternalsoftwareWatchdog. Also the PN- GincludesanMCUthatactsasafailsafeexternalwatchdog.TheMCUpowercycles thesystem,if noactivityisdetectedfor1 hour. Accelerometer The accelerometer can be used for motion detection and driver behavior monitoring. 2.
3 SoftwareFeatures 3.1 Basic Software Items Requirement Network Interface IP Stack Upgrade Method Remote Update Power Modes AT Commands Report Drivers GPIOs 2G IPV4/IPV6 Remoteupdate/PCtool Supported – including OMA DM Supported Supported Supported: 1000 records GPIO，LED，GPS，UART, Accelerometer InterruptforIgnitionStatus, Buzzer, Relay LEDs Watch Dog Reset Start up Banner GPSStatus,NetworkStatus Supported Softreset,hardreset, GPS reset, RF reset Supported 3.
• Trip start and stop Anyhardwareorsoftwareresetwillreturnthedevicetofullpowermode. 3.4 AT Commands Extended AT commands are specific to the PN-G device. They are closely based on commands that are as similar as possible industry common devices and are essentially subsets of standard PN-G commands. Native AT commands supported by the Mediatek 2503 chipset are also available via the serial and USB interfaces. 3.
3.7.1 Context Preservation Whenaself-initiated resetisperformeddue toNetworkWatchdog orbytheResetcommand (modes0,1),the contextofthesystemisbeingpreservedandisrestoredafterthereset.Thecontextincludesall theperiodictimers,thereportqueue,theodometer,etc.Thisallowstoresettheunitasa troubleshootingor preventive measurewithoutlosingreports thatarealreadyinthequeueorarependingonrunningtimers.Notethattheresetprocessmay cause1-2minofinaccuracyinthetimersandshouldnotbeconsideredasveryprecise. 3.
4 TestMethod 4.1 Hardware Test Item Description Baseband FunctionTest • • • • • • • • • • Power InputTest Power Consumption and CurrentTest Heat DissipationTest UARTStabilityTest GPIOLevelTest LED StabilityTest DropDownTest ESDTest High/LowTemperatureTest HumidityTest RFTest • • • RF PerformanceTest GPS PerformanceTest Antenna PerformanceTest 4.2 Software Test TestEnvironmentConstruct Me s s ageTestenvironment 1.USBdongleandPCasmessageserver 2.SendmessagetoPN-G UDP Testenvironment 1.
Panther eopar PN-G d MechanicalStructure (mm) 11
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
RF Specification BT Operation Frequency: Maximum Power 2402~2480MHz 6.57dBm(E.I.R.P.) GSM Operation Frequency: Maximum Power (E-GSM 900): Maximum Power (DCS 1800): E-GSM 900: 880~915MHz DCS 1800: 1710~1785MHz 29.9dBm 25.8dBm GNSS Operation Frequency: L1: 1559MHz~1610MHz We Pointer Telocation INC.
Pointer Telocation INC. EU Declaration of Conformity for Radio Equipment Directive (RED) 2014/53/EU We, Pointer Telocation INC._hereby, declare that the essential requirements set out in the Radio Equipment Directive (RED) 2014/53/EU have been fully fulfilled on our product with indication below: Address: 7715 NW 48th Street, Suite 395 Doral, FL 33166 USA Product Name: MiniTrack 2G Model: CM900100-000 Brand Name: N/A Hardware Version: P2 Software Version: MM12_V1.0.
Pointer Telocation INC. The following standards have been applied for the investigation of compliance: Draft ETSI EN 301 489-1 V2.2.1 (2019-03) Draft ETSI EN 301 489-17 V3.2.0 (2017-03) ETSI EN 301 489-19 V2.1.1 (2019-04) Draft ETSI EN 301 489-52 V1.1.0 (2016-11) ETSI EN 300 328 V2.1.1 (2016-11) ETSI EN 303 413 V1.1.1 (2017-06) ETSI EN 301 511 V12.5.
Pointer Telocation INC. Name: Igor Rogov Title: VP R&D Tel. No.: +972-73-2622320 E-mail: Igorr@pointer.
