Instruction Manual PowErBox PionEEr
Dear PowerBox customer, Congratulations on your decision to install a PowerBox Pioneer in your model. This unit is currently the most modern integrated power management system available anywhere in the model world. The Pioneer offers full telemetry capability in addition to a high-performance power supply featuring electronic switches. Furthermore, in conjunction with an iGyro SAT the Pioneer operates as a highly sophisticated gyro system.
FEATURES + 14 channels + High-performance battery backer with high continuous load capacity + Duplicated circuitry for the entire power electronics + Redundant electronic switch + All features can be controlled using PowerBox and Jeti transmitters + All systems can be operated using BlueCom or PowerBox USB + Integrated iGyro technology of the latest type, with iGyro SAT as gyro sensor + Nine independent gyro outputs for: 3x aileron, 3x elevator, 3x rudder + Special regulatory algorithm for fixed-wing models
1. INSTALLATION, CONNECTIONS In order to minimise the Pioneer’s physical size the case does not feature mounting lugs; the unit is simply installed using the self-adhesive pad supplied. This mounting method is extremely secure since the unit is so light and compact. The Pioneer can be used with three types of radio control system: PowerBox CORE P²BUS, Futaba S.BUS2, Jeti EX-BUS and Spektrum SRXL2.
receiver is connected, then it must be connected to RX1 for telemetry transmission. If you have connected a GPS III to the FastTrack input, the Pioneer also sends the GPS information to the transmitter. - Futaba S.BUS2 Connect the S.BUS2 output of one or two receivers to RX1 and RX2. If only one receiver is connected, then it must be connected to RX1 for telemetry transmission. This receiver must also be set as the telemetry receiver at the transmitter.
data displayed for the PowerBox sensor. If you have connected a GPS III to the FastTrack input, the Pioneer also sends the GPS information to the transmitter. By default the Pioneer operates in DX18 compatibility mode. The DX18 and DX20 mode can be selected using Terminal via USB or BlueCom. Connecting the batteries Ideally the two batteries connected to the Pioneer should be of the same type and capacity. It is essential to maintain correct polarity.
Connecting an iGyro SAT If you wish to exploit the Pioneer’s gyro functionality by fitting an iGyro SAT, it is essential to install the unit at the correct angle in the model. In turbinepowered models the iGyro SAT should be located as far as possible from the engine in order to prevent turbine noise influencing the sensor. The lead attached to the iGyro SAT can be extended to any length. The iGyro SAT should be connected to the Pioneer’s FastTrack input.
2. BASIC SETTINGS If you are not using an iGyro with the PowerBox Pioneer, only a few settings have to be entered. You will find all the settings either in the transmitter menu (CORE, Jeti) or the Mobile App and the PC program. To access the menu on the PowerBox CORE transmitter, create any Telemetry widget for the Pioneer; you will then find the Menu button in the widget. On a Jeti transmitter you will find the Jetibox point under Additional functions. Se-lect this point, then select MX at far right.
d) Failsafe This menu is used to select an output which will move to a pre-defined servo position if the radio signal is lost. Always use this function for Throttle. It is a legal requirement in many countries! Select the output you wish to use, and set the Failsafe mode to Failsafe. Pressing the Teach button stores the current servo positions for all outputs for which Failsafe has been set. 3. GYRO SETTINGS None of the iGyro settings have a function unless an iGyro SAT is connected.
b) An already test-flown model - Assign the gyro outputs - Learn the installed position - Learn the centre and end-points - Adjust the iGyro in flight using the gain control - Fine-tune the individual axes if necessary - Store the established gain value on a switch As you can see, while you are carrying out basic adjustments to a new model, or test-flying a new model without the gyro, no adjustments of any kind are required at the iGyro SAT or the Pioneer.
4. MENU STRUCTURE General Settings Fine Tuning Input Mapping Gyro Setup Firmware Version Axis Selection CH Aileron A Range Selection CH Aileron B Teach Mounting Pos. Gain CH Aileron C Attitude Assist CH Elevator A Characteristic CH Elevator B Stick Priority CH Elevator C Lock Feel CH Rudder A Airspeed Factor CH Rudder B Framerate CH Reset Cap. Reset Gyro Teach Stick Endpoints CH Rudder C CH Gain www.powerbox-systems.
5. SPECIFICATION Operating voltage: Power supply: Current drain Power-on state: Current drain Standby: Maximum load current: Drop-out voltage: Output voltage: Signal input: Supported RC systems: Receiver redundancy: Channels: Servo sockets: Servo signal resolution: Signal frame rate. Gyro regulation: Gyro sensor type: Number of sensor axes: Supported telemetry systems: Dimensions: Weight: Weight Sensor Switch: Temperature range: 12 4.0 V – 9.
6. DIMENSIONS www.powerbox-systems.
7. SET CONTENTS - PowerBox Pioneer + MicroSwitch - 2 patch leads 22 cm - 2 retaining screws - Adhesive tape - Operating instructions in English and German - PowerBox Pioneer + MicroMag - Magnet - 2 patch leads 22 cm - 2 retaining screws - White adhesive tape - Sticker MagSensor - Key ring - Operating instructions in English and German 8. SERVICE NOTE We make every effort to provide a good service to our customers, and have now established a Support Forum which covers all queries relating to our products.
9. GUARANTEE CONDITIONS At PowerBox-Systems we insist on the highest possible quality standards in the development and manufacture of our products. They are guaranteed “Made in Germany”! That is why we are able to grant a 24 month guarantee on our Pioneer from the initial date of purchase. The guarantee covers proven material faults, which will be corrected by us at no charge to you.
10. LIABILITY EXCLUSION We are not in a position to ensure that you observe our instructions regarding installation of the PowerBox Pioneer, fulfil the recommended conditions when using the unit, or maintain the entire radio control system competently. For this reason we deny liability for loss, damage or costs which arise due to the use or operation of the PowerBox Pioneer, or which are connected with such use in any way.
NOTES www.powerbox-systems.
12/2020 PowerBox-Systems GmbH Ludwig-Auer-Straße 5 D-86609 Donauwörth Germany +49-906-99 99 9-200 +49-906-99 99 9-209 www.powerbox-systems.
