ENGLISH R Instruction Manual Manual de Instrucciones Manuel d’Instructions PPB300E ESPAÑOL For Occasional Use Only Electrolux Home Products, Inc. 1030 Stevens Creek Road Augusta, GA 30907 Copyright E2006 Electrolux Home Products, Inc. 545058737 1/23/06 FRANÇAIS DANGER: Read and follow all Safety Rules and Operating Instructions before using this product. Failure to do so can result in serious injury.
SAFETY RULES WARNING: When using gardening appliances, basic safety precautions must always be followed to reduce the risk of fire and serious injury. Hazard Zone DANGER: This power tool can be dangerous! This unit can cause serious injury including amputation or blindness to the operator and others. The warnings and safety instructions in this manual must be followed to provide reasonable safety and efficiency in using the unit.
S Wear hearing protection. S Never start or run the engine inside a closed room or building. Breathing exhaust fumes can kill. S Keep handles free of oil and fuel. S Always use the handlebar and a properly adjusted shoulder strap with a blade (see ASSEMBLY). water heaters, electric motors or switches, furnaces, etc. S Always store gasoline in a container approved for flammable liquids. CUTTING SAFETY WARNING: Inspect the area to be cut before each use.
screen. If you operate in a locale where such regulations exist, you are legally responsible for maintaining the operating condition of these parts. Failure to do so is a violation of the law. For normal homeowner use, the muffler and spark arresting screen will not require any service. After 50 hours of use, we recommend that your muffler be serviced or replaced by your authorized service dealer. ASSEMBLY CARTON CONTENTS 2. 3.
HARNESS ADJUSTMENT FOR BALANCE Screw Handlebar Bracket Cover 6 inches (15 cm) below waist Mounting Bracket 30 inches (76 cm) 4 -- 12 inches (10 -- 30 cm) above ground ASSEMBLY OF SHOULDER STRAP WARNING: Proper shoulder strap and handlebar adjustments must be made with the engine completely stopped before using unit. 1. Insert your right arm and head through the shoulder strap and allow it to rest on your left shoulder.
ASSEMBLY INFORMATION -- WEED BLADE To remove metal shield, loosen and remove the four mounting screws. See ATTACHING THE METAL SHIELD and INSTALLATION OF THE METAL BLADE for illustrations. Be sure to store all parts and instructions for future use. ATTACHING THE PLASTIC SHIELD AND TRIMMER HEAD WEED BLADE WARNING: The shield must be properly installed.
NOTE: Make sure all parts are in place as il- INSTALLATION OF THE METAL BLADE lustrated, and the blade is sandwiched between the dust cup and the retaining washer. There should be no space between the blade and the dust cup or the retaining washer. 7. Align hole in dust cup with hole in side of gearbox by rotating the blade. 8. Insert a small screwdriver into aligned holes. This will keep the shaft from turning while tightening the blade nut.
OPERATION KNOW YOUR UNIT READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT. Compare the illustrations with your unit to familiarize yourself with the location of the various controls and adjustments. Save this manual for future reference.
STARTING A FLOODED ENGINE Flooded engines can be started by placing the ON/OFF switch in the ON position. Move the start lever to the RUN position and fully squeeze throttle trigger. Pull the starter handle repeatedly while squeezing throttle trigger until engine starts and runs. This could require pulling the starter handle many times, depending on how badly the unit is flooded. If the unit still doesn’t start, refer to TROUBLESHOOTING TABLE or call 1-800-554-6723.
Coupler Upper Shaft Primary Hole Guide Recess Locking/ Release Button Attachment WARNING: Make sure the locking/ release button is locked in the primary hole and the knob is securely tightened before operating the unit. All attachments are designed to be used in the primary hole unless otherwise stated in the applicable attachment instruction manual. Using the wrong hole could lead to serious injury or damage to the unit.
OPERATING INSTRUCTIONS FOR USE WITH WEED BLADE Trimming 3 inches (8 cm) above ground SCALPING -- The scalping technique removes unwanted vegetation down to the ground. Hold the bottom of the trimmer head about 3 inches (8 cm) above the ground and at an angle. Allow the tip of the line to strike the ground around trees, posts, monuments, etc. This technique increases line wear. Scalping MOWING -- Your trimmer is ideal for mowing in places conventional lawn mowers cannot reach.
S Do not swing unit with such force that you are in danger of losing your balance. Bring the engine to cutting speed before entering the material to be cut.If the blade does not turn when you squeeze the throttle trigger, make sure shaft is fully inserted into the engine. Always release the throttle trigger and allow engine to return to idle speed when not cutting. The blade should not turn while the engine is running at idle. If the blade turns at idle, do not use your unit.
CULTIVATOR SAFETY WARNING: Rotating tines can cause serious injury. Keep away from rotating tines. Stop the engine and disconnect the spark plug before unclogging tines or making repairs. S Do not use a cutting blade that is bent, warped, cracked, broken or damaged in any other way. Have worn or damaged parts replaced by an authorized service dealer. S Always keep unit in front of your body. Keep all parts of your body away from the cutting blade. S Keep the cutting blade and air vents clear of debris.
S Always stop the unit when work is delayed or when walking from one cutting location to another. S If you strike or become entangled with a foreign object, stop the engine immediately and check for damage. Have any damage repaired by an authorized service dealer before attempting further operations. Discard blades that are bent, warped, cracked or broken. S Stop the unit immediately if you feel excessive vibration. Vibration is a sign of trouble.
INSPECT AND CLEAN UNIT AND DECALS S After each use, inspect complete unit for loose or damaged parts. Clean the unit and decals using a damp cloth with a mild detergent. S Wipe off unit with a clean dry cloth. CLEAN AIR FILTER A dirty air filter decreases engine performance and increases fuel consumption and harmful emissions. Always clean after every 5 hours of operation. 1. Clean the cover and the area around it to keep dirt from falling into the carburetor chamber when the cover is removed. 2.
The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions: S Engine will not idle when the throttle is released. S The trimmer head, blade or optional attachment moves/spins at idle. Make adjustments with the unit supported so the cutting attachment is off the ground and will not make contact with any object. Hold the unit by hand while running and making adjustments.
TROUBLESHOOTING TABLE WARNING: Always stop unit and disconnect spark plug before performing all of the recommended remedies below except remedies that require operation of the unit. TROUBLE CAUSE REMEDY Engine will not start. 1.ON/OFF switch in OFF position. 2. Engine flooded. 1. Move ON/OFF switch to the ON position. 2. See “Starting a Flooded Engine” in Operation Section. 3. Fill tank with correct fuel mixture. 4. Install new spark plug. 5. Check for dirty fuel filter; replace.
LIMITED WARRANTY ELECTROLUX HOME PRODUCTS, INC., warrants to the original purchaser that each new Poulan PRO® brand gasoline tool or attachment is free from defects in material and workmanship and agrees to repair or replace under this warranty any defective gasoline product or attachment as follows from the original date of purchase. 2 YEARS -- Parts and Labor, when used for household purposes. 90 DAYS -- Parts and Labor, when used for commercial, professional, or income producing purposes.
WARRANTY COMMENCEMENT DATE: The warranty period begins on the date the small off--road engine is purchased. LENGTH OF COVERAGE: This warranty shall be for a period of two years from the initial date of purchase. WHAT IS COVERED: REPAIR OR REPLACEMENT OF PARTS. Repair or replacement of any warranted part will be performed at no charge to the owner at an approved ELECTROLUX HOME PRODUCTS, INC., servicing center.
