Product Manual

4
CAUTION: Do not operate this lawn
mower without the discharge guard or an
entire approved grass catcher in place.
These guards are for your protection and
are required by the American National
Standards Institute and Consumer Prod-
ucts Safety Com mis sion.
CAUTION: Disconnect spark plug wire
from spark plug and place wire where it
cannot come in contact with plug.
HOW TO SET UP YOUR LAWN
MOW ER
UNFOLD HANDLE
IMPORTANT: Unfold handle carefully so
as not to pinch or damage con trol cables.
2 POSITION / “ADJUSTABLE” HANDLES
• Raise handles until lower handle section
locks into place in operating position.
ASSEMBLY
TO REMOVE MOWER FROM CARTON
• Remove all loose parts from carton.
• Remove lawn mower hous ing with care. Avoid touch ing blade under hous ing. Always
wear gloves or other protection when working under or lifting mower.
THINGS TO KNOW BE FORE YOU ASSEMBLE OR OPERATE YOUR LAWN
MOW ER
Do I have a side or rear discharge lawn
mower?
Look for the grass discharge opening on
your mower. If the opening is on the right
side of the mower housing, it is a side
discharge mower. If the opening is at the
back of the mower housing, it is a rear dis-
charge mower. Only rear discharge lawn
mowers have a grass catcher in clud ed with
the mower. Approved grass catchers for
side discharge mow ers may be purchased
from your nearest au tho rized dealer.
Do I have a mulching lawn mower?
Look for the grass discharge opening on
your mower. Raise the discharge guard
(rear door on rear discharge mowers). If
the opening is closed off by a plate, then
your lawn mower is mulcher ready. To
convert to a discharging mower, see the
Operation section of this manual.
LEFT
HAND
SIDE
RIGHT
HAND
SIDE
FRONT
What is the right and left side of the
lawn mower?
When right hand (RH) or left hand (LH) is
mentioned in this man ual, it means when
you are in the operating po si tion (stand ing
be hind the handle).
What kind of engine is on my lawn
mower?
When learning how to operate your new
lawn mower, you will need to know what
kind of engine powers the mower. A decal
on the engine will indicate the man u -
fac tur er and type or brand name of the
engine.
BRIGGS & STRATTON ENGINES
BACK or REAR
(Op er at ing Position)
®
HONDA
ENGINES
TECUMSEH
EN GINES
21
• Place new drive belt in engine pulley
and belt retainer of debris shield.
MODELS WITH GEARCASE-MOUNTED
BELT KEEPER:
• Remove drive cover.
• Remove spring and belt keeper.
• Remove belt from gearcase pulley.
• Turn lawn mower on its side. See
engine manual for proper direction of
turning over the engine.
• Remove blade, engine pulley and debris
shield.
• Remove engine pulley and belt from
debris shield.
• Return mower to upright po si tion.
• Install new belt on gearcase pulley.
• Reinstall belt keeper and spring.
• Reinstall drive cover.
NOTE: Always use factory approved belt
to assure proper fi t and long life.
• Turn lawn mower on its side with air fi lter
and car bu re tor down.
• Reinstall blade.
ENGINE
CARBURETOR
The carburetor has been preset at the fac-
tory and ad just ment should not be neces-
sary. However, minor ad just ment may be
required to compensate for differences in
fuel, temperature, altitude or load.
• The air fi lter must be assembled to the
car bu re tor when running engine.
• Best carburetor adjustment is obtained
when fuel tank is 1/4 full.
• In order for the engine to run, the opera-
tor presence control bar must be held
in the operating position. There fore,
and assistant will be required to hold
the control bar in the operating position
when making fi nal adjustment to the
car bu re tor.
See the ADJUSTMENT section of your
engine manual for further instructions.
ENGINE SPEED
The engine speed has been factory set.
Do not attempt to increase engine speed
as it may result in personal injury. If you
believe the engine is running too fast
or too slow, take your lawn mower to an
authorized engine service center for repair
and adjustment.
THROTTLE CONTROL
If it becomes necessary to adjust or re-
place the throttle control, see the ADJUST-
MENT section of your engine man ual.
Belt
Drive
cover
Belt
keeper
Gearcase pulley
Spring
Debris shield
Drive belt
Belt
retainer
Engine pulley
• Route the other end of the new drive belt
through hole in housing.
• Reinstall debris shield.