Assembly Instruction

ManualsBrandsPottery Barn ManualsOther RoomsPottery Barn Puzzle Single Cubby

Page 1/5

pottery barn kids

PUZZLE

WALL

SINGLE

CUBBY

WITH

DOOR

PRE-ASSEMBLY:

•

Read all instructions before beginning assembly. The illustrations provided allow for easier assembly when used in

conjunction with the assembly instructions.

•

For your safety and ease, assembly by two adults is recommended.

•

Remove all parts and hardware from the box and lay out on a clean, carpeted, or scratch- free work surface.

Use care as some parts or hardware may have sharp points or edges.

•

Do not dispose of any contents until assembly is completed to avoid accidentally discarding small

parts and hardware.

•

Use the parts and hardware lists to identify and separate each of the pieces included.

•

Note: Do not fully tighten all bolts until all parts are in place. Failure to follow these instructions may cause the bolts

misalign during assembly.

•

The use of power tools for assembly is not recommended. Power tools can damage hardware or split wood

PARTS INCLUDED:



(A) Top End panel (1)



(AA) Bottom End panel (1)



(B) Right Side panel (1)



(BB) Left Side panel

(with pre-drilled holes for door)(1)



(D) Back panel (1)

PARTS AND HARDWARE REQUIRED (Packaged Separately):



Double-Wide and/or Triple-Wide Bases



Base Screws:

o Double Wide Bases include:

(8) Screws- 8 X 1”

o Triple-Wide Bases include:

(12) Screws- 8 X 1”

TOOLS REQUIRED: (not included)



Phillips head screwdriver

CUBBY HARDWARE ENCLOSED



(E) LONG SCREW-8X1” (10)



(F) CAM LOCK (8)



(G) CAM LOCK BOLT (8)



(H) WOOD DOWEL (8)



(I) WOOD SCREW-3x15mm (4).



(J) ESPRESSO STICKER-22mm (8)

CONNECTING HARDWARE ENCLOSED:



(a): U PLATE(2)



(b): SHORT SCREW-8X3/4” (8)

Summary of content (5 pages)

PAGE 1
pottery barn kids PUZZLE WALL SINGLE CUBBY WITH DOOR PRE-ASSEMBLY: • Read all instructions before beginning assembly. The illustrations provided allow for easier assembly when used in conjunction with the assembly instructions. • For your safety and ease, assembly by two adults is recommended. • Remove all parts and hardware from the box and lay out on a clean, carpeted, or scratch- free work surface. Use care as some parts or hardware may have sharp points or edges.
PAGE 2
ASSEMBLY INSTRUCTIONS: 1. Insert (4) Wood Dowels (H) into the pre-drilled holes on the Side Panels (B) and (BB) (Figure 1). Then, fasten the (4) Cam Lock Bolts (G) into the predrilled holes in Top Panel (A) and Bottom Panel (AA), using the Phillips Head Screwdriver as shown in Figure 2. Do not over tighten the Cam Lock Bolts or the Cam Locks will not properly engage in Steps 2 and 3. B AA BB Figure 1 Figure 2 2.
PAGE 3
5. Secure the Back Panel (D) with (10) Long Screws (E), using the Phillips Head Screwdriver (not included) (Figure 6). BACK VIEW Figure 6 6. Attach the Door (C) to the Left Side Panel (BB), with (4) Wood Screws (I), using the Phillips Head Screwdriver (not included). AA ( Figure 7).
PAGE 4
COMPLETING THE ASSEMBLY: Your Puzzle Wall System contains a set of individual components that can be attached together in a variety of combinations to suit your own space. To assemble the set together, please follow these steps: 1. Choose your preferred layout by arranging the Puzzle Wall Cubbies together as desired, atop the Bases (packaged separately). If needed, loosen or tighten the adjustable levers on the underside of the Bases to ensure that your system will sit firmly on the ground.
PAGE 5
3. Attach the individual Puzzle Components together by fastening the U Plates (a) with (4) Screws (b) each along the back edges, as shown below, using the Phillips Head Screwdriver (not included). BACK VIEW As a safety precaution, please follow the instructions enclosed to secure the Puzzle Wall Unit to the wall using the tipping-restraint kit included. CARE INSTRUCTIONS: a Dust often using a clean, soft, dry lint-free cloth.