Assembly Instruction

ManualsBrandsPottery Barn ManualsOther RoomsPottery Barn Puzzle L Cubby

pottery barn kids

PUZZLE

WALL

L-SHAPED

CUBBY

PRE-ASSEMBLY:

•

Read all instructions before beginning assembly. The illustrations provided allow for easier assembly when used in

conjunction with the assembly instructions.

•

For your safety and ease, assembly by two adults is recommended.

•

Remove all part and hardware from the box and lay out on a clean, carpeted, or scratch- free work surface. Use

care as some parts or hardware may have sharp points or edges.

•

Do not dispose of any contents until assembly is completed to avoid accidentally discarding small parts and hardware.

•

Use the parts and hardware lists to identify and separate each of the pieces included.

•

Note: Do not fully tighten all bolts until all parts are in place. Failure to follow these instructions may cause the bolts

misalign during assembly.

•

The use of power tools for assembly is not recommended. Power tools can damage hardware or split wood.

PARTS INCLUDED:



(A) Top Panel (1)



(B) Middle Panel (1)



(D) Long Side Panel (1)



(E) Medium Side Panel (1)



(EE) Short Side Panel (1)



(F) Back Panel (1)

CUBBY HARDWARE ENCLOSED



(G) CAM LOCK (12)



(H) CAM LOCK BOLT (12)



(I) WOOD DOWEL (12)



(J) LONG SCREW- 8X1” (18)



(K) ESPRESSO STICKER-22mm (12)

CONNECTING HARDWARE ENCLOSED:



(a): U PLATE(2)



(b) SHORT SCREW- 8X3/4” (8)

PARTS AND HARDWARE REQUIRED (Packaged Separately):



Double-Wide and/or Triple-Wide Bases



Base Screws:

o Double Wide Bases include:

(8) Screws- 8 X 1”

o Triple-Wide Bases include:

(12) Screws- 8 X 1”

TOOLS REQUIRED: (not included)



Phillips head screwdriver

Page 1/5

Summary of content (5 pages)

PAGE 1
pottery barn kids PUZZLE WALL L-SHAPED CUBBY PRE-ASSEMBLY: • Read all instructions before beginning assembly. The illustrations provided allow for easier assembly when used in conjunction with the assembly instructions. • For your safety and ease, assembly by two adults is recommended. • Remove all part and hardware from the box and lay out on a clean, carpeted, or scratch- free work surface. Use care as some parts or hardware may have sharp points or edges.
PAGE 2
ASSEMBLY INSTRUCTIONS: 1. Insert (4) Wood Dowels (I) into the pre-drilled holes on each Side Panel (D) (E) and (EE) (Figure 1). Then, fasten (4) Cam Lock Bolts (H) into the predrilled holes in each Top Panel (A), Middle Panel (B) and Bottom panel(C), using the Phillips Head Screwdriver as shown in Figure 2. Do not over tighten the Cam Lock Bolts or the Cam Locks will not properly engage in Steps 2, 3 and 4. EE E Figure 1. Figure 2 2.
PAGE 3
. Attach the Long Side Panel (D) and Short Side Panel (EE) to the bottom panel (C), as shown. Insert the back panel (F) through the U-groove on the side panel. Insert Cam Lock (G) into each of the (4) corresponding holes on the Side Panels (D/EE) and tighten using Phillips Head Screwdriver. (Figure 4). D EE G G C Figure 4 4. Place the Step 2 Assembly onto the Step 3 Assembly, as shown.
PAGE 4
6. Secure the Back Panel (F) with (18) Long Screws (J), using the Phillips Head Screwdriver (not included) (Figure 6). A F D BACK VIEW Figure 6 COMPLETING THE ASSEMBLY: Your Puzzle Wall System contains a set of individual components that can be attached together in a variety of combinations to suit your own space. To assemble the set together, please follow these steps: 1. Choose your preferred layout by arranging the Puzzle Wall Cubbies together as desired, atop the Bases (packaged separately).
PAGE 5
2. Turn pieces upside down and fasten the Bases to the Bottom Cubbies using the 8 X 1” screws, as shown below. BASE Fasten from the underside of the Base through the underside of the Cubby 3. Attach the individual Puzzle Components together by fastening the U Plates (a) with (4) Screws (b) each along the back edges, as shown, using the Phillips Head Screwdriver (not included).