Assembly Instruction

ManualsBrandsPottery Barn ManualsOther RoomsPottery Barn Puzzle Double Cubby with Door

Page 1/5

pottery barn kids

PUZZLE WALL DOUBLE CUBBY

PRE-ASSEMBLY:

• Read all instructions before beginning assembly. The illustrations provided allow for easier assembly

when used in conjunction with the assembly instructions.

• For your safety and ease, assembly by two adults is recommended.

• Remove all part and hardware from the box and lay out on a clean, carpeted, or scratch- free work

surface. Use care as some parts or hardware may have sharp points or edges.

• Do not dispose of any contents until assembly is completed to avoid accidentally discarding small parts

and hardware.

• Use the parts and hardware lists to identify and separate each of the pieces included.

• Note: Do not fully tighten all bolts until all parts are in place. Failure to follow these instructions may cause

the bolts misalign during assembly.

• The use of power tools for assembly is not recommended. Power tools can damage hardware or split

wood.

PARTS

INCLUDED:



(A)

End

panel

(2)



(B)

Side

panel

(2)



(C)

Adjustable

Shelf

(1)



(D)

Back

Panel

(1)

HARDWARE

ENCLOSED



(E)

LONG

SCREW-8X1”

(12)



(F)

CAM

LOCK

(8)



(G)

CAM

LOCK

BOLT

(8)



(H)

WOOD

DOWEL

(8)



(I)

MAGIC

WIRE

(2)



(J)

ESPRESSO

STICKER

(8)

CONNECTING

HARDWARE

ENCLOSED:



(a):

PLATE(2)



(b)SHORT

SCREW-8X3/4”

(8)

PARTS

AND

HARDWARE

REQUIRED

(Packaged

Separately):



Double-Wide

and/or

Triple-Wide

Bases



Base

Screws:

Double

Wide

Bases

include:

(8)

Screws-

1”

Triple-Wide

Bases

include:

(12)

Screws-

1”

TOOLS

REQUIRED

(not

included)



Phillips

head

screwdriver

Summary of content (5 pages)

PAGE 1
pottery barn kids PUZZLE WALL DOUBLE CUBBY PRE-ASSEMBLY: • Read all instructions before beginning assembly. The illustrations provided allow for easier assembly when used in conjunction with the assembly instructions. • For your safety and ease, assembly by two adults is recommended. • Remove all part and hardware from the box and lay out on a clean, carpeted, or scratch- free work surface. Use care as some parts or hardware may have sharp points or edges.
PAGE 2
ASSEMBLY INSTRUCTIONS: 1. Insert (4) Wood Dowels (H) into the pre-drilled holes on each Side Panel (B) (Figure 1). Then, fasten the Cam Lock Bolts (G) into the (4) predrilled holes in each End Panel (A), using the Phillips Head Screwdriver as shown in Figure 2. Do not over tighten the Cam Lock Bolts or the Cam Locks will not properly engage in Steps 2 and 3. Figure 1. Figure 2 2. Attach the (2) Side Panels (B) onto one End Panel (A), as shown.
PAGE 3
4. Use Phillips screwdriver to tighten all the Cam Locks using the (8) Espresso Sticker (J) to cover the corresponding pre-drilled holes. 5. Secure the Back Panel (D) with (12) Screws (E), using the Phillips Head Screwdriver (not (Figure 6). included) BACK VIEW Figure 6 6. Place the (2) Magic Wires (I) into the pre-drilled holes in the Side Panels (B) at the desired height. the Adjustable Shelf (C) (Figure 7). Figure 7.
PAGE 4
COMPLETING THE ASSEMBLY: Your Puzzle Wall System contains a set of individual components that can be attached together in a variety of combinations to suit your own space. To assemble the set together, please follow these steps: 1. Choose your preferred layout by arranging the Puzzle Wall Cubbies together as desired, atop the Bases (packaged separately). If needed, loosen or tighten the adjustable levers on the underside of the Bases to ensure that your system will sit firmly on the ground. L eft 2.
PAGE 5
3. Attach the individual Puzzle Components together by fastening the U Plates (a) with (4) Screws (b) each along the back edges, as shown below, using the Phillips Head Screwdriver (not included). BACK VIEW a As a safety precaution, please follow the instructions enclosed to secure the Puzzle Wall Unit to the wall using the tipping-restraint kit included. CARE INSTRUCTIONS: • Dust often using a clean, soft, dry lint-free cloth.