Assembly Instruction

ManualsBrandsPottery Barn ManualsOther RoomsPottery Barn Cameron Locker

pottery barn kids

CAMERON LOCKER

IMPORTANT SAFETY INSTRUCTIONS:

Please read all instructions carefully before assembling.

For your safety, assembly by two people is recommended.

HARDWARE INCLUDED:

(L) Allen Key – 1pc

(M) Allen Bolt ¼” x 25mm – 8pcs

(N) Spring Washer ¼” – 8pcs

(O) Flat Washer ¼” – 8pcs

(P) Small Bolt 5/32“ x 19mm – 4pcs

(Q) Door Pull – 2pcs

(R) Shelf Support – 16pcs

(S) Large Wood Screw 4 x 30mm – 8pcs

(T) Small Wood Screw 3.5 x

12mm – 4pcs

(U) Hook – 2pcs

(V) Plastic Cap – 4pcs

(W) Medium Wood Screw 4 x

20mm – 3pcs

PRE-ASSEMBLY:

• Remove all parts and hardware from the box and lay out on a clean, carpeted, or scratch-free work surface, as

this will avoid damaging any parts during assembly. The shipping box provides an ideal work surface. Do not

dispose of any contents until assembly is completed to avoid accidentally discarding small parts or hardware.

• Use the parts and hardware lists above to identify and separate each of the pieces included.

• The illustrations provided allow for easier assembly when used in conjunction with the assembly instructions.

• Note: Do not fully tighten all bolts until all parts are in place. Failure to follow these instructions may cause the

bolts to misalign during assembly.

• If using power tools to aid in assembly please use caution. Power tools can damage hardware or split wood.

PARTS INCLUDED:

(A) Left Side Panel – 1pc

(B) Right Side Panel – 1pc

(D) Lower Shelf – 1pc

(E) Long Divider – 1pc

(F) Short Divider – 1pc

(G) Bottom Panel – 1pc

(H) Left Door – 1pc

(I) Right Door – 1pc

(J) Top Panel – 1pc

(K) Adjustable Shelf – 4pcs

TOOLS REQUIRED:

Philips Screwdriver (Not Included)

Summary of content (7 pages)

PAGE 1
pottery barn kids CAMERON LOCKER IMPORTANT SAFETY INSTRUCTIONS: Please read all instructions carefully before assembling. For your safety, assembly by two people is recommended.
PAGE 2
ASSEMBLY INSTRUCTIONS: 1. Align and connect the wooden dowels of the Lower Shelf (D) to the pre-drilled holes on the Left Side Panel (A). (Fig. 1) 2. Align and connect the wooden dowels of the Back Panel (C) to the pre-drilled holes and slot on the Left Side Panel (A) (Fig. 2) D. C. A. (Fig. 2) (Fig. 1) 3. Align and attach the pre-drilled holes of the Right Side Panel (B) to the wooden dowels on the assembled piece.
PAGE 3
4. Align and insert the wooden dowels of both the Long Divider (E) and the Short Divider (F) into the pre-drilled holes on the top and underside of the Lower Shelf (D), as shown below. Ensure that the labels with arrow on the Long/Short Dividers (E & F) are facing each other. (Fig. 4). E. F. E. F. (Fig. 4) 5.
PAGE 4
6. Turn the assembled piece upright. Place the Top Panel (J) on the assembled piece. Align the pre-drilled holes of the Top Panel (J) to the wooden dowels of the Left Side, Right Side, Back Panels and the Long Divider (A, B, C & E). Insert (4) Plastic Caps (V) into the pre-drilled holes on the Lower Shelf (D) and bottom front of the Top Panel (J). (Fig. 6). J. C A E B V. (Fig. 6) 7.
PAGE 5
9. Insert the (16) Shelf Support Pegs (R) into the pre-drilled holes on interior sides of the Left/Right Side Panels (A & B) and Long Dividers (E). Place the Adjustable Shelves (K) on the Shelf Support Pegs (R). (Fig. 9) K. (Fig. 9) 10. Insert and secure the Hooks (U) into the pilot holes located on the Back Panel using (4) Small Wood Screws (T).
PAGE 6
Mending Plate Connections: HARDWARE ENCLOSED T-Shape Bracket - 2pcs -16pcs - 1pc Square Bracket • • Wood Screw 3 x 12mm If connecting Cubby piece to Base piece, use (2) T-Shape Bracket and (12) Wood Screw. If connecting to Cubby piece to Cubby piece, use (1) Square Bracket and (4) Wood Screw. T-Shape Bracket Square Bracket Screw Screw Thank you for your purchase. stores | catalog | www.potterybarnkids.com USA 1.800.290.
PAGE 7
pottery barn kids TIP RESTRAINT KIT WARNING: This product is only a deterrent. It is not a substitute for proper adult supervision. Young children may be injured by tipping furniture and the use of a tipping restraint is highly recommended. When properly installed, this restraint could provide protection against the unexpected tipping of furniture. We recommend mounting this restraint to a wall stud. All Parts and Hardware are included with the Cameron Locker.