Assembly Instruction

ManualsBrandsPottery Barn ManualsOther RoomsPottery Barn Cameron Cubby

pottery barn kids

CAMERON CUBBY WITH DOORS AND DIVIDERS

IMPORTANT SAFETY INSTRUCTIONS:

Please read all instructions carefully before assembling.

For your safety, assembly by two people is recommended.

HARDWARE LIST

(J) Allen Key

- 1pc

(K) Bolt ¼“ x 25mm

- 8pcs

(L) Spring Washer 1/4“ - 8pcs

(M) Flat Washer 1/4“

- 8pcs

(N) Plastic Cap

- 4pcs

(O) Long Wood Screw 4 x 30mm

- 6pcs

(P) Short Wood Screw 3 x 12mm - 16pcs

(Q) Square Bracket

– 1pc

(R) T-Shape Bracket

– 2pcs

PART LIST

(A) Top Panel – 1pc

(B) Bottom panel – 1pc

(D) Right Side Panel – 1pc

(E) Divider – 3pcs

(F) Back Panel – 1pc

(G) Shelf – 1pc

(H) Left Door – 1pc

(I) Right Door – 1pc

TOOLS REQUIRED:

Phillips Screwdriver

(Not included)

PRE-ASSEMBLY:

• Remove all parts and hardware from the box and lay out on a clean, carpeted, or scratch-free work

surface, as this will avoid damaging any parts during assembly. The shipping box provides an ideal work

surface. Do not dispose of any contents until assembly is completed to avoid accidentally discarding small

parts or hardware.

• Use the parts and hardware lists above to identify and separate each of the pieces included.

• The illustrations provided allow for easier assembly when used in conjunction with the assembly

instructions.

• Note: Do not fully tighten all bolts until all parts are in place. Failure to follow these instructions may

cause the bolts to misalign during assembly.

• If using power tools to aid in assembly please use caution. Power tools can damage hardware or split

wood.

ASSEMBLY INSTRUCTIONS:

1. Connect the Left/Right Side Panel (C & D) to the Shelf (G) by aligning the wooden dowels on the Shelf

(G) to the pre-drilled holes on the Left/Right Side Panel (C & D). Make sure the slots on both panels are

facing inwards. (Fig. 1)

2. Align and secure the (3) Divider (E) to the Shelf (G) using (6) Long Wood Screw (O). (Fig. 2)

(Fig. 1)

(Fig. 2)

Summary of content (4 pages)

PAGE 1
pottery barn kids CAMERON CUBBY WITH DOORS AND DIVIDERS IMPORTANT SAFETY INSTRUCTIONS: Please read all instructions carefully before assembling. For your safety, assembly by two people is recommended.
PAGE 2
3. Place the Top Panel (A) on the assembled piece. Insert (4) Bolt (K), Spring Washer (L) and Flat Washer (M) from the pre-drilled holes on the Left/Right Side Panels (C & D) to the pre-drilled holes on the Top Panel (A). (Fig. 3) 4. Slide the Back Panel (F) into the slots on the Left/Right Side Panel (C & D). (Fig. 4) A. M. L. K. J. F. (Fig. 3) (Fig. 4) 5. Put the assembled piece upside down on the work surface. Insert (4) Plastic Cap (N) into the pre-drilled holes on the Shelf (G) and Bottom Panel (B).
PAGE 3
6. Upright the assembled cubby. Check alignment and tighten all bolts and screws. 7. When connecting to other stacking Cameron cubby piece, place a T-Shape Bracket (R) over the predrilled holes on back of the cubby pieces securing with (6) Short Wood Screw (P). Repeat with the other T-Shape Bracket (R) on the other side. (Fig. 6) 8. When connecting to side Cameron cubby piece, place a Square Bracket (Q) over the pre-drilled holes on the cubby pieces. (Fig.
PAGE 4
pottery barn kids TIP RESTRAINT KIT WARNING: This product is only a deterrent. It is not a substitute for proper adult supervision. Young children may be injured by tipping furniture and the use of a tipping restraint is highly recommended. When properly installed, this restraint could provide protection against the unexpected tipping of furniture. We recommend mounting this restraint to a wall stud. All Parts and Hardware are included with the Cameron Wall Cubby.