Instructions

ManualsBrandsPOTTER ManualsNotification SystemPOTTER PVX 100M Mass Notification System

Table Of Contents

PVX 100M

Mass Notification System

SN2

1 = OFF 8 sec. initial delay

2 = ON

3 = OFF

4 = ON 8 sec. repeat delay

5 = OFF

6 = ON Message On

7 = OFF 3 Repeats

8 = ON

FACTORY DEFAULT SWITCH SETTINGS:

SN1

1 = OFF Temporal Whoop Signal

2 = X Do not use

3 = X Do not use

4 = Fault Code Lock

5 = X Do not use

6 = AC Fault Delay

7 = ON Battery connected

8 = ON Mic connected

1 8

OFF

Switch Network Detail

P/N 1-5001M R3.14

SN1

SN2

LED 4

LED 5

TB5

TB5: PVC-RMI

TER 1:

(NOTE 2, 4, 6)

Circuit Neg

TER +24VDC (0.5A)

TER Audio -

TER Audio +

TER RS 485 -

TER RS 485 +

TER 7: No Connection

P8: I2C Port

10 Pin Connector

PVC-ZM/SL8/IL8/OL8

All other terminals are identical to the PVC-100 Module.

Please refer to P/N 1-5001 R2.14 for full installation

Instructions and ratings

PVX 100M

PVX 200M

1) Speaker Circuits

2) Speaker Circuitsand 1) PVC-100E

Contains 1) PVC-100M

The PVX 100M Mass Notification System is functionally identical to the PVX 100 with the exception of an Intelligent Interface for an LOC.

The PVX 100M may be used as an ACU and combined with accessory modules to meet the requirements of UL2572. The system system

provides a Physical and Communication Security Level 1, Audit Control Level 2, Stored Data and Access Control Security Level 0 per UL

2572 Mass Notification Standard. The system is designed to be used in conjunction with a UL listed Fire Alarm Control Panel (FACP) to

provide a Listed Voice Evacuation Alarm System with Mass Notification capabilities.

The FACP provides all Fire initiating circuitry and a signaling circuit to the PVX 100M. The PVX 100M provides its own internal

supervision as well as supervision for its speaker lines and accessories. Any fault is reported back to the FACP. In normal standby the

supervisory circuit from the panel is connected to a matching EOLR. Should the PVX 100M suffer an internal failure or should there be any

fault on the speaker line or accessory a contact would open and the FACP would report it as an open fault for that circuit.

The PVX 100M is designed to be powered from 120 VAC at 60 Hz and will provide 100W of audio. Speakers may be 25 or 70 Vrms (jumper

selected, 25V is factory set). See Installation Instruction P/N PVX 25-50-100 R2.14 for all Electrical Specifications, Standard Terminal

Designations and Wiring Diagrams.

MODELS: The PVC-100M is a complete Voice Evac/MNS Module, it is complete with built-in tones and messages for Fire and MNS. The

PVC-100M may be coupled with additional PVC-100E Expander modules for systems requiring greater power.

The PVX 100M and PVX 200M are complete Voice Evacuation Panels. Where greater Audio power is required they meay be combined with

Expander panels, PVX 100E/200E/300E/400E/500E/600E. When using any EVX Expander Module, refer to installation instructions P/N 1-

5002 R2.14.

Note: All Switch settings refer to Fire Tone/Message only.

All MNS Tone/Messages must be Pre-Configured for System.

MNS Tone/Messages will play continuous until reset.

For technical assistance please call:

866-956-1211

5757 Phantom Dr. St. Louis, Missouri 63042

www.pottersignal.com

firealarmresources.com

Summary of content (4 pages)

PAGE 1
PVX 100M Mass Notification System The PVX 100M Mass Notification System is functionally identical to the PVX 100 with the exception of an Intelligent Interface for an LOC. The PVX 100M may be used as an ACU and combined with accessory modules to meet the requirements of UL2572. The system system provides a Physical and Communication Security Level 1, Audit Control Level 2, Stored Data and Access Control Security Level 0 per UL 2572 Mass Notification Standard.
PAGE 2
Fig. 3 Typical connection from PVC-100M to PVC-SL8 and PVC-RM8 PVC-100M TB1 P7 1 2 3 5 4 6 7 8 11 10 9 8 7 6 5 4 3 2 1 J1 2 1 1 2 3 4 5 6 7 8 MSG GAIN 1 2 3 TB3 YEL GRN J2 70V 25V LED 1 FAULT LED2 NORMAL LED 3 RED Switches used for Message activation will indicate Red for Alarm or Green for MNS Messages. TB2 ALARM Switches used for Output activation will indicate Red.
PAGE 3
PVX 100M w/FACP NAC PVX 100M SL8 Fire *MNS FACP Input Control NAC Booster Strobe Output OL8 PVC-100M Fire *MNS NAC Booster must be Listed to UL2572 / UL1481 Monitor Module *1 MNS Override Monitor Module NAC Fault The PVX 100M may be used in conjunction with a UL Listed FACP. The FACP must be capable of monitoring contacts for Fault conditions and Supervisory conditions in order to report a MNS override.
PAGE 4
For technical assistance please call: 866-956-1211 5757 Phantom Dr. St. Louis, Missouri 63042 www.pottersignal.com P/N 1-5001M R3.14 firealarmresources.