Instructions / Assembly

Post Proservative Sticks are for treatment of pole
structures, dimensional lumber (round stock, square
stock) or any non-food contact wood. Post Proservative
sticks are recommended for protection against fungal
decay and insects. Post Proservative sticks can be
used for all wood species.
Genics Inc
Wood Preservative for Remedial
Treatment of Utility Poles, Posts, Pilings
Millwork, Decks, Window Joinery
and any non-food contact piece of wood.
Protection of Wood Against
Fungal Decay and Insects
KEEP OUT OF REACH OF CHILDREN
CAUTION
FIRST AID
if Swallowed: Call a poison control center or doctor
immediately for treatment advice. Have person sip a glass of
water if able to swallow. Do not induce vomiting unless told to
do so by a poison control center or doctor. Do not give
anything by mouth to an unconscious person.
If on Skin or Clothing: Take off contaminated clothing.
Rinse skin immediately with plenty of water for 15 - 20
minutes. Call poison control center or doctor for treatment
advice. If Inhaled: Move person to fresh air. If person is not
breathing, call 911 or an ambulance, then give artificial
respiration, preferably by mouth-to-mouth, if possible. Call a
poison control center or doctor for further treatment advice.
If in Eyes: Hold eye open and rinse slowly and gently with
water for 15-20 minutes. Remove contact lenses, if present,
after the first 5 minutes, then continue rinsing eye. Call a
poison control center or doctor immediately for treatment
advice.
Have the product container or label with you
when calling a poison control center or doctor.
CONTAINS INGREDIENTS LISTED BELOW FUSED AT HIGH
TEMPERATURE TO FORM WATER SOLUBLE, CLEAR
HARD AND GLASS-LIKE ROD. COMPARED TO THE
CRYSTALLINE INGREDIENTS, THE GLASS RODS FUNCTION
AS A SLOW-RELEASE SYSTEM. Post Proservative Sticks
ARE MANUFACTURED IN DIFFERENT SIZES AND WEIGHTS
INCLUDING SMALL WAFERS AND PELLETS.
ACTIVE INGREDIENTS:
Disodium Octaborate Tetrahydrate 90.6%
Boric Acid .................................................................... 4.7%
Cup r i c Hy d r o x i d e (C A S 2 0 4 2 7 -59- 2 ) 2. 9 %
(as Copper Metal .................................................... 1.89%)
INERT INGREDIENTS ................................................ 1.8%
TOTAL .................................................................... 100.0%
US EPA Reg. No. 71653-2 US EPA Est. No. 71653-CAN-01
Genies Inc.
561 Acheson Rd. — 53016 Hwy 60
Acheson, Alberta TTX 5A7
[phone] fax: [phone]
Install Instructions (POSTS):
- Drill 3/8"” treatment holes at a 45-degree angle in the
ground line area as specified in the table above. Refer to the
Loading Table for number of borings, boring depths, and
Post Proservative stick load rate.
-Keep maximum 6” vertical separation between drill holes as
required starting at ground line. Start at Ground Line and drill
next holes 6” below ground line rotating 120 deg as much as
possible as needed. If unable to install below ground line
install Post Proservative sticks at ground line area.
- Take care that the drill does not exit on the opposite side of
the post.
- Insert Post Proservative sticks tapered end first.
- Plug the bored holes with the appropriate size Plug. A 7/16”
Plug fits a 3/8” drill hole.
- Plug may be removed using a Pro Plug removal tool by
inserting the tool into the slot on the head of the plug and
twisting in a counter clockwise direction or by using a 3/16”
flat screwdriver.
- If treating a smaller size post, a steeper treatment boring
angle may be used to ensure there is adequate room for the
stick and plug without drilling through structure.
Post Size
Post
Proservative
Sticks
Boring
Depth
(inches)
# of
Borings
4x4
1
3.75
1
4x6
2
3.75
2
6x6
2
3.75
2
3Ply 2X6
2
3.75
2
4Ply 2X6
2
3.75
2
3Ply 2X8
3
3.75
3
4 Ply 2X8
3
3.75
3
8X8
3
3.75
3
3.5" Dia ROUND
1
3.75
2
6" Dia ROUND
2
3.75
1